Pressurized temperature-variable water tunnel for high Reynolds number research

2002 ◽  
Author(s):  
C. Holze ◽  
H. Oelze ◽  
H. Rath
Keyword(s):  
Reynolds Number ◽  
High Reynolds Number ◽  
Water Tunnel ◽  
Temperature Variable ◽  
High Reynolds ◽  
Variable Water

Characterization of the Custom-Designed, High Reynolds Number Water Tunnel

2016 ◽  
Author(s):  
Yasaman Farsiani ◽  
Brian R. Elbing
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Test Section ◽  
High Reynolds Number ◽  
Layer Growth ◽  
Water Tunnel ◽  
Freestream Velocity ◽  
Section Design ◽  
High Reynolds

This paper reports on the characterization of the custom-designed high-Reynolds number recirculating water tunnel located at Oklahoma State University. The characterization includes the verification of the test section design, pump calibration and the velocity distribution within the test section. This includes an assessment of the boundary layer growth within the test section. The tunnel was designed to achieve a downstream distance based Reynolds number of 10 million, provide optical access for flow visualization and minimize inlet flow non-uniformity. The test section is 1 m long with 15.2 cm (6-inch) square cross section and acrylic walls to allow direct line of sight at the tunnel walls. The verification of the test section design was accomplished by comparing the flow quality at different location downstream of the flow inlet. The pump was calibrated with the freestream velocity with three pump frequencies and velocity profiles were measured at defined locations for three pump speeds. Boundary layer thicknesses were measured from velocity profile results and compared with analytical calculations. These measurements were also compared against the facility design calculations.

Design of a Recirculating Water Tunnel for the Study of High-Reynolds Number Turbulent Boundary Layers

2015 ◽  
Author(s):  
Libin Daniel ◽  
Shahrouz Mohagheghian ◽  
Dalton Dunlap ◽  
Eric Ruhlmann ◽  
Brian R. Elbing
Keyword(s):  
Reynolds Number ◽  
Boundary Layers ◽  
High Reynolds Number ◽  
Low Cost ◽  
Turbulent Boundary Layers ◽  
Regulation System ◽  
Water Tunnel ◽  
Overall Design ◽  
Design Considerations ◽  
High Reynolds

This paper reports on the design and fabrication of a high-Reynolds number recirculating water tunnel, which will be used primarily for the study of turbulent boundary layers with an emphasis on drag reduction applications. The primary design specifications were (i) achieve a momentum thickness based Reynolds number above 10,000, (ii) maximize optical access, and (iii) minimize flow non-uniformity. This paper discusses the design considerations and procedures to meet each of these design criteria as well as the manufacturing of the components, installation, and design of auxiliary systems such as the pressure regulation system. There are several recirculating water tunnels at universities that can achieve comparable Reynolds numbers, but they were either built with at least double the budget of the current project or are refurbished tunnels from other laboratories (i.e. key design considerations were already fixed). Thus, the current work offers a guide for the overall design of a low-cost, high-Reynolds number water tunnel. A brief review of other recirculating high-Reynolds number water tunnels is included. Currently, installation has begun with the fabrication complete.

scholarly journals Design and Validation of a Recirculating, High-Reynolds Number Water Tunnel

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Brian R. Elbing ◽  
Libin Daniel ◽  
Yasaman Farsiani ◽  
Christopher E. Petrin
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Test Section ◽  
High Reynolds Number ◽  
Water Tunnel ◽  
Laminar To Turbulent Transition ◽  
Turbulent Transition ◽  
Profile Matching ◽  
Final Design ◽  
High Reynolds

Commercial water tunnels typically generate a momentum thickness based Reynolds number (Reθ) ∼1000, which is slightly above the laminar to turbulent transition. The current work compiles the literature on the design of high-Reynolds number facilities and uses it to design a high-Reynolds number recirculating water tunnel that spans the range between commercial water tunnels and the largest in the world. The final design has a 1.1 m long test-section with a 152 mm square cross section that can reach speed of 10 m/s, which corresponds to Reθ=15,000. Flow conditioning via a tandem configuration of honeycombs and settling-chambers combined with an 8.5:1 area contraction resulted in an average test-section inlet turbulence level <0.3% and negligible mean shear in the test-section core. The developing boundary layer on the test-section walls conform to a canonical zero-pressure-gradient (ZPG) flat-plate turbulent boundary layer (TBL) with the outer variable scaled profile matching a 1/7th power-law fit, inner variable scaled velocity profiles matching the log-law and a shape factor of 1.3.

Modeling and Simulation of High Reynolds' Number Flows During Reaction Injection Mold Filling

1994 ◽  
Vol 9 (3) ◽  
pp. 279-285 ◽  
Author(s):  
Rahima K. Mohammed ◽  
Tim A. Osswald ◽  
Timothy J. Spiegelhoff ◽  
Esther M. Sun
Keyword(s):  
Reynolds Number ◽  
Modeling And Simulation ◽  
High Reynolds Number ◽  
Mold Filling ◽  
Injection Mold ◽  
High Reynolds ◽  
Reynolds Number Flows
Sign in / Sign up

Export Citation Format

Share Document