scholarly journals Active Combustion Control for aircraft gas turbine engines

2000 ◽  
Author(s):  
John DeLaat ◽  
Kevin Breisacher ◽  
Joseph Saus ◽  
Daniel Paxson
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Combustion Control ◽  
Active Combustion Control

High Response Valve for Active Combustion Control

2001 ◽  
Author(s):  
Dong N. Wu ◽  
Joseph W. Michalski ◽  
Link C. Jaw ◽  
Kenneth Semega
Keyword(s):  
Gas Turbine ◽  
Piezoelectric Actuator ◽  
High Response ◽  
Turbine Engines ◽  
Bench Test ◽  
Gas Turbine Engines ◽  
Combustion Control ◽  
Flow Rates ◽  
Active Combustion Control ◽  
Modulation Control

This paper describes the development of a prototype high response fuel valve using piezoelectric actuator for fuel modulation control in gas turbine engines. In flow bench test, this prototype valve demonstrated 5∼11% peak-to-peak modulation strength at flow rates up to approximately 1500 pph and frequencies up to 500 Hz.

Active Combustion Control by Fuel Forcing at Non-Coherent Frequencies

2007 ◽  
Author(s):  
Chukwueloka O. Umeh ◽  
Leonardo C. Kammer ◽  
Corneliu Barbu
Keyword(s):  
Gas Turbine ◽  
Pressure Fluctuations ◽  
Open Loop ◽  
Turbine Engines ◽  
Nox Emissions ◽  
Gas Turbine Engines ◽  
Combustion Control ◽  
Combustion Dynamics ◽  
Loop Control ◽  
Active Combustion Control

One impediment to substantially further the reductions in NOx emissions for aviation gas turbine engines is thermal-acoustic instabilities, also referred to as combustion dynamics. Dynamics arise due to the coupling of heat and pressure fluctuations in such systems. Numerous passive and semi-active control schemes, including performance de-rating and fuel staging, have been developed for land-based gas turbine engines. However, many of these schemes are not well suited to aviation engines, as a result of their weight and bulk. Observations of several combustors operating on either gaseous or liquid fuels show that the dominant dynamic frequencies have a special relation to specific non-coherent lower frequencies. Experiments show that combinations of two of these non-coherent frequencies form the dominant tones of the combustor. As part of NASA’s intelligent engines program, active combustion control is used to mitigate dynamics, as the combustor’s bulk fuel-air ratio (FAR) is made leaner in an effort to reduce NOx emissions by about 85% below the Committee on Aviation Environmental Protection (CAEP) 6 limit. In the feedback control scheme suggested in this paper, a small percentage of the overall fuel flow is pulsed at a given non-coherent frequency and with varying amplitude. The effectiveness of the dynamics reduction approach has been demonstrated via preliminary open loop control tests on a liquid-fuelled partially premixed high-pressure combustion test rig at GE Aviation in Evendale, Ohio.

Gas Screen in Components of Gas Turbine Engines

1997 ◽  
Vol 28 (7-8) ◽  
pp. 536-542
Author(s):  
A. A. Khalatov ◽  
I. S. Varganov
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Gas Screen

Potential Application of Composite Materials to Future Gas Turbine Engines

1988 ◽  
Author(s):  
James C. Birdsall ◽  
William J. Davies ◽  
Richard Dixon ◽  
Matthew J. Ivary ◽  
Gary A. Wigell
Keyword(s):  
Composite Materials ◽  
Gas Turbine ◽  
Potential Application ◽  
Turbine Engines ◽  
Gas Turbine Engines

Method of tribodiagnostics of d-30KU engines/KP with the use of a microwave plasma complex: results of metrological examination and analysis of the accuracy

2020 ◽  
pp. 22-29
Author(s):  
A. Bogoyavlenskiy ◽  
A. Bokov
Keyword(s):  
Gas Turbine ◽  
Microwave Plasma ◽  
Technical Condition ◽  
The State ◽  
Turbine Engines ◽  
Metrological Examination ◽  
Gas Turbine Engines ◽  
High Frequency Plasma ◽  
Frequency Plasma ◽  
Primary Standards

The article contains the results of the metrological examination and research of the accuracy indicators of a method for diagnosing aircraft gas turbine engines of the D30KU/KP family using an ultra-high-frequency plasma complex. The results of metrological examination of a complete set of regulatory documents related to the diagnostic methodology, and an analysis of the state of metrological support are provided as well. During the metrological examination, the traceability of a measuring instrument (diagnostics) – an ultrahigh-frequency plasma complex – is evaluated based on the scintillation analyzer SAM-DT-01–2. To achieve that, local verification schemes from the state primary standards of the corresponding types of measurements were built. The implementation of measures to eliminate inconsistencies identified during metrological examination allows to reduce to an acceptable level the metrological risks of adverse situations when carrying out aviation activities in industry and air transportation. In addition, the probability of occurrence of errors of the first and second kind in the technological processes of tribodiagnostics of aviation gas turbine engines is reduced when implementing a method that has passed metrological examination in real practice. At the same time, the error in determining ratings and wear indicators provides acceptable accuracy indicators and sufficient reliability in assessing the technical condition of friction units of the D-30KP/KP2/KU/KU-154 aircraft engines.

On the prospects of application of nanostructured heterophase polyfunctional composite materials inengine building industry

2019 ◽  
pp. 50-57
Author(s):  
O. B. Silchenko ◽  
M. V. Siluyanova ◽  
V. Е. Nizovtsev ◽  
D. A. Klimov ◽  
A. A. Kornilov
Keyword(s):  
Composite Materials ◽  
Gas Turbine ◽  
Developed Countries ◽  
The United States ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Nanostructured Composite ◽  
Polymer Metal ◽  
Long Operation ◽  
Prospects Of Application

The paper gives a brief review of properties and applications of developed extra-hard nanostructured composite materials and coatings based on them. The presentresearch suggestsaerospace applications of nanostructured composite materials based on carbides, carbonitrides and diboridesof transition and refractory metals. To improve the technical and economic performance of gas turbine engines, it is advisable to use new composite structural materials whose basic physicomechanical properties are several times superior to traditional ones. The greatest progress in developing new composites should be expected in the area of materials created on the basis of polymer, metal, intermetallic and ceramic matrices. Currently components and assemblies of gas turbine engines and multiple lighting power units with long operation life and durability will vigorously develop. Next-generation composites are studied in all developed countries, primarily in the United States and Japan.

scholarly journals Progress in Novel Electrodeposited Bond Coats for Thermal Barrier Coating Systems

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4214
Author(s):  
Kranthi Kumar Maniam ◽  
Shiladitya Paul
Keyword(s):  
Gas Turbine ◽  
Thermal Barrier Coating ◽  
Gas Turbines ◽  
High Performance ◽  
Turbine Engines ◽  
Thermal Barrier ◽  
Gas Turbine Engines ◽  
Potential Cost ◽  
Bond Coats ◽  
Barrier Coating

The increased demand for high performance gas turbine engines has resulted in a continuous search for new base materials and coatings. With the significant developments in nickel-based superalloys, the quest for developments related to thermal barrier coating (TBC) systems is increasing rapidly and is considered a key area of research. Of key importance are the processing routes that can provide the required coating properties when applied on engine components with complex shapes, such as turbine vanes, blades, etc. Despite significant research and development in the coating systems, the scope of electrodeposition as a potential alternative to the conventional methods of producing bond coats has only been realised to a limited extent. Additionally, their effectiveness in prolonging the alloys’ lifetime is not well understood. This review summarises the work on electrodeposition as a coating development method for application in high temperature alloys for gas turbine engines and discusses the progress in the coatings that combine electrodeposition and other processes to achieve desired bond coats. The overall aim of this review is to emphasise the role of electrodeposition as a potential cost-effective alternative to produce bond coats. Besides, the developments in the electrodeposition of aluminium from ionic liquids for potential applications in gas turbines and the nuclear sector, as well as cost considerations and future challenges, are reviewed with the crucial raw materials’ current and future savings scenarios in mind.

Sign in / Sign up

Export Citation Format

Share Document