Use of two-component fluids of microencapsulated PCM for heat transfer in spacecraft thermal systems

1994 ◽  
Author(s):  
J. Mulligan ◽  
D. Colvin ◽  
Y. Bryant
Keyword(s):  
Heat Transfer ◽  
Thermal Systems ◽  
Two Component

Heat transfer models for two-component media with interfacial jump

2015 ◽  
Vol 96 (2) ◽  
pp. 247-260 ◽  
Author(s):  
I. Gruais ◽  
D. Poliševski
Keyword(s):  
Heat Transfer ◽  
Two Component ◽  
Transfer Models

CFD-DEM Numerical Simulation and Experimental Validation of Heat Transfer and Two-Component Flow in Fluidized Bed

2017 ◽  
Vol 16 (1) ◽  
Author(s):  
Feihong Guo ◽  
Zhaoping Zhong
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Fluidized Bed ◽  
Quartz Sand ◽  
Thermal Imager ◽  
Gas Velocity ◽  
Bed Height ◽  
Two Component ◽  
Superficial Gas Velocity ◽  
Infrared Thermal Imager

AbstractBased on the improved computational fluid dynamics and discrete element method (CFD-DEM), heat transfer and two-component flow of biomass and quartz sand have been studied from experiments and numerical simulation in this paper. During experiments, the particle temperature and moving images are respectively recorded by infrared thermal imager and high speed camera. With the increase of the velocity, the mixing index (MI) and the cooling rate of the particles are rising. Due to larger heat capacity and mass, the temperature of biomass drops slower than that of quartz sand. Fictitious element method is employed to solve the incompatibility of the traditional CFD-DEM where the cylindrical biomass are considered as an aggregation of numerous fictitious sphere particles arranged in certain sequence. By the comparison of data collected by infrared thermal imager and the simulated results, it can be concluded that experimental data is basically agreement with numerical simulation results. Directly affected by inflow air (25℃), the average temperature of particles in the bed height area (h>30 mm) is about 3 degrees lower than that of the other heights. When the superficial gas velocity is larger, the fluidization is good, and the gas temperature distribution is more uniform in the whole area. On the contrary, bubbles are not easy to produce and the fluidization is restricted at lower superficial gas velocity. Gas-solid heat transfer mainly exists under the bed height of 10 mm, and decreases rapidly on fluidized bed height. The mixing index (MI) is employed to quantitatively discuss the mixing effectiveness, which first rises accelerate, then rising speed decreases, finally tends to a upper limit.

scholarly journals Effect of corrugated minichannel variable width on entropy generation for convective heat transfer of alpha-Alumina-water nanofluid

2021 ◽  
Vol 2053 (1) ◽  
pp. 012016
Author(s):  
N M Muhammad ◽  
N A C Sidik ◽  
A Saat ◽  
Y Asako ◽  
W M A A Japar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Entropy Production ◽  
Convective Heat ◽  
Entropy Generation ◽  
Entropy Generation Rate ◽  
Thermal Systems ◽  
Volume Fractions ◽  
Thermal Entropy ◽  
Alpha Alumina

Abstract Energy management and sustainability in thermal systems require maximum utilization of resources with minimal losses. However, it is rarely unattainable due to the ever-increasing need for a high-performance system combined with device size reduction. The numerical study examined convective heat transfer of an alpha-Alumina-water nanofluid in variable-width corrugated minichannel heat sinks. The objective is to study the impact of nanoparticle volume fractions and flow area variation on the entropy generation rate. The determining variables are 0.005 – 0.02 volume fractions, the fluid velocity 3 – 5.5 m/s and heat flux of 85 W/cm2. The numerical results show an acceptable correlation with the experiment results. The results indicate the thermal entropy production drop with an increase in nanoparticles volume fraction. Contrastingly, the frictional resistance entropy suggests the opposite trend due to the turbulence effect on the fluid viscosity. The induction of Alumina-Water nanofluid with enhanced thermal conductivity declined the entropy generation rate compared to water alone. The increase in width ratio by 16% between the cases translates to at least a 9% increase in thermal entropy production. The outcome of this study can provide designers and operators of thermal systems more insight into entropy management in corrugated heatsinks.

Energy Transport Mechanisms in Nanofluids and Its Applications

2009 ◽  
Author(s):  
Yimin Xuan ◽  
Qiang Li
Keyword(s):  
Heat Transfer ◽  
Energy Transport ◽  
Transfer Mechanism ◽  
Thermal Engineering ◽  
Energy Transfer Mechanism ◽  
Transport Mechanisms ◽  
Thermal Systems ◽  
Flow And Heat Transfer ◽  
Solid Liquid ◽  
Suspended Nanoparticles

Nanofluid is a solid-liquid mixture consisting of solid nanoparticles or nanofibers with sizes typically of 1–100 nm suspended in liquid. Thermal conductivity and heat transfer performance of nanofluids is superior to those of the original pure carrier fluids because the suspended nanoparticles remarkably improve energy exchange capability of the suspensions. In the present paper, the investigations efforts cover microscopic and mesoscaled approachs for the heat transfer enhancement mechanism of the nanofluid, flow and heat transfer mechanism and the relevant control methods of the magnetic fluid by suspending magnetic nanoparticles in base fluids, and some applications of nanofluid on a variety of thermal systems in order to understand energy transfer mechanism of nanofluids and guide future applications of nanofluids to thermal engineering.

Sign in / Sign up

Export Citation Format

Share Document