Finite-element panel flutter in three-dimensional supersonic unsteady potential flow

AIAA Journal ◽  
1977 ◽  
Vol 15 (12) ◽  
pp. 1677-1683 ◽  
Author(s):  
T. Y. Yang ◽  
S. H. Sung
Keyword(s):  
Finite Element ◽  
Potential Flow ◽  
Three Dimensional ◽  
Panel Flutter

Three Dimensional Inviscid Computation of an Impeller Flow

1983 ◽  
Author(s):  
T. C. Prince ◽  
A. C. Bryans
Keyword(s):  
Finite Element ◽  
Potential Flow ◽  
Three Dimensional ◽  
Method Comparison ◽  
Centrifugal Impeller ◽  
Published Data ◽  
Flow Method ◽  
Streamline Curvature ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The flow in a centrifugal impeller is analyzed by a quasi-three-dimensional streamline curvature method, by a three-dimensional Euler code, and by a three-dimensional finite element potential flow method. Comparison with Eckardt’s published data for a backswept impeller shows that full three-dimensional methods better predict the loading at the hub and shroud.

scholarly journals A Finite Element Computer Code to Calculate Full 3–D Compressible Potential Flow in Turbomachinery

1984 ◽  
Author(s):  
Doğan Güneş ◽  
Muhsin Mengütürk
Keyword(s):  
Finite Element ◽  
Potential Flow ◽  
Compressible Flows ◽  
Velocity Potential ◽  
Three Dimensional ◽  
Axial Flow ◽  
Computer Code ◽  
Turbine Rotor ◽  
Electric Utility ◽  
Quadratic Interpolation

A Finite element computer code is presented for calculation of three-dimensional compressible flows in turbomachinery under the steady and potential flow limitations. The method used relies upon a variational statement equivalent to the classical velocity potential formulation of this problem. The solution domain is discretized by using hexahedral superelements each composed of six ten-node tetrahedral elements enabling quadratic interpolation of velocity potential. The code offers the flexibility of choosing a combination of subparametric and isoparametric elements. Application of the code to the Gostelow cascade, an experimental turbine stator, the first stage stator and rotor of an electric utility axial flow turbine and finally to a mixed flow turbine rotor are presented. The validity of the results are established by comparison with the exact solution, experimental data and calculations by other numerical methods.

Three-Dimensional Inviscid Computation of an Impeller Flow

1984 ◽  
Vol 106 (2) ◽  
pp. 523-528 ◽  
Author(s):  
T. C. Prince ◽  
A. C. Bryans
Keyword(s):  
Finite Element ◽  
Potential Flow ◽  
Three Dimensional ◽  
Method Comparison ◽  
Centrifugal Impeller ◽  
Published Data ◽  
Flow Method ◽  
Streamline Curvature ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The flow in a centrifugal impeller is analyzed by a quasi-three-dimensional streamline curvature method, by a three-dimensional Euler code, and by a three-dimensional finite element potential flow method. Comparison with Eckardt’s published data for a backswept impeller shows that full three-dimensional methods better predict the loading at the hub and shroud.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

Comparison of Conventional and Pontic Fixed Partial Dentures Over Implants Using the Finite Element Method: Three-Dimensional Analysis of Cortical and Medullary Bone Stress

2020 ◽  
Vol 46 (3) ◽  
pp. 175-181
Author(s):  
Marcelo Bighetti Toniollo ◽  
Mikaelly dos Santos Sá ◽  
Fernanda Pereira Silva ◽  
Giselle Rodrigues Reis ◽  
Ana Paula Macedo ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Medullary Bone ◽  
Principal Stresses ◽  
Bone Stress ◽  
Bone Damage ◽  
Rehabilitation System ◽  
Minimum Requirements

Rehabilitation with implant prostheses in posterior areas requires the maximum number of possible implants due to the greater masticatory load of the region. However, the necessary minimum requirements are not always present in full. This project analyzed the minimum principal stresses (TMiP, representative of the compressive stress) to the friable structures, specifically the vestibular face of the cortical bone and the vestibular and internal/lingual face of the medullary bone. The experimental groups were as follows: the regular splinted group (GR), with a conventional infrastructure on 3 regular-length Morse taper implants (4 × 11 mm); and the regular pontic group (GP), with a pontic infrastructure on 2 regular-length Morse taper implants (4 × 11 mm). The results showed that the TMiP of the cortical and medullary bones were greater for the GP in regions surrounding the implants (especially in the cervical and apical areas of the same region) but they did not reach bone damage levels, at least under the loads applied in this study. It was concluded that greater stress observed in the GP demonstrates greater fragility with this modality of rehabilitation; this should draw the professional's attention to possible biomechanical implications. Whenever possible, professionals should give preference to use of a greater number of implants in the rehabilitation system, with a focus on preserving the supporting tissue with the generation of less intense stresses.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Modeling for Steel Cord Analysis in Radial Tires

2013 ◽  
Vol 41 (1) ◽  
pp. 60-79 ◽  
Author(s):  
Wei Yintao ◽  
Luo Yiwen ◽  
Miao Yiming ◽  
Chai Delong ◽  
Feng Xijin
Keyword(s):  
Finite Element ◽  
High Efficiency ◽  
Force Measurement ◽  
Three Dimensional ◽  
Local Stress ◽  
Tension Force ◽  
Center Line ◽  
Element Analysis ◽  
Design Variables ◽  
Steel Cord

ABSTRACT: This article focuses on steel cord deformation and force investigation within heavy-duty radial tires. Typical bending deformation and tension force distributions of steel reinforcement within a truck bus radial (TBR) tire have been obtained, and they provide useful input for the local scale modeling of the steel cord. The three-dimensional carpet plots of the cord force distribution within a TBR tire are presented. The carcass-bending curvature is derived from the deformation of the carcass center line. A high-efficiency modeling approach for layered multistrand cord structures has been developed that uses cord design variables such as lay angle, lay length, and radius of the strand center line as input. Several types of steel cord have been modeled using the developed method as an example. The pure tension for two cords and the combined tension bending under various loading conditions relevant to tire deformation have been simulated by a finite element analysis (FEA). Good agreement has been found between experimental and FEA-determined tension force-displacement curves, and the characteristic structural and plastic deformation phases have been revealed by the FE simulation. Furthermore, some interesting local stress and deformation patterns under combined tension and bending are found that have not been previously reported. In addition, an experimental cord force measurement approach is included in this article.

Sign in / Sign up

Export Citation Format

Share Document