Three-dimensional vortex theory for axial compressor blade rows at subsonic and transonic speeds

AIAA Journal ◽  
1970 ◽  
Vol 8 (7) ◽  
pp. 1275-1283 ◽  
Author(s):  
OLUFEMI OKUROUNMU ◽  
JAMES E. McCUNE
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Compressor Blade ◽  
Vortex Theory

Numerical Investigation of End Wall Boundary Layer Removal on Highly Loaded Axial Compressor Blade Rows

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
V. Gümmer ◽  
M. Goller ◽  
M. Swoboda
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Flow Path ◽  
Compressor Blade ◽  
Main Flow ◽  
Layer Removal ◽  
Wall Boundary Layer ◽  
End Wall ◽  
Highly Loaded

This paper presents results of numerical investigations carried out to explore the benefit of end wall boundary layer removal from critical regions of highly loaded axial compressor blade rows. At the loading level of modern aero engine compressors, the performance is primarily determined by three-dimensional (3D) flow phenomena occurring in the end wall regions. Three-dimensional Navier–Stokes simulations were conducted on both a rotor and a stator test case in order to evaluate the basic effects and the practical value of bleeding air from specific locations at the casing end wall. The results of the numerical survey demonstrated substantial benefits of relatively small bleed rates to the local flow field and to the performance of the two blade rows. On the rotor, the boundary layer fluid was removed from the main flow path through an axisymmetric slot in the casing over the rotor tip. This proved to give some control over the tip leakage vortex flow and the associated loss generation. On the stator, the boundary layer fluid was taken from the flow path through a single bleed hole within the passage. Two alternative off-take configurations were evaluated, revealing a large impact of the bleed hole shape and the location on the cross-passage flow and the suction side corner separation. On both blade rows investigated, rotor and stator, the boundary layer removal resulted in a reduction of the local reverse flow, blockage, and losses in the respective near-casing region. This paper gives insight into changes occurring in the 3D passage flow field near the casing and summarizes the effects on the radial matching and pitchwise-averaged performance parameters, namely loss and deviation of the rotor and stator when suction is active. Primary focus is put on the aerodynamics in the blade rows in the main flow path; details of the internal flow structure within the bleed off-take cavities/ports are not discussed here.

Structural and Dynamic Optimization of a Single Axial Compressor Blade Using the Gradient-Based Method

2014 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Alexander V. Sheremetyev ◽  
Viktor V. Tykhomirov ◽  
Alexey V. Petrov
Keyword(s):  
Finite Element ◽  
Optimization Problems ◽  
Thickness Distribution ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Compressor Blade ◽  
Element Analysis ◽  
Programming Technique ◽  
Sizing Optimization ◽  
Aerodynamic Properties

This paper describes the development of an in-house code for sizing optimization of blades with constraints imposed on blade’s natural frequencies and static stresses. The optimization environment includes a three-dimensional parametric model of the blade, interface functions for automated execution of the static and modal finite element analyses as well as post-processing of the results, and optimization algorithm. The blade geometry is represented by section profiles at a number of span-wise stations. Each blade section profile is parametrized by nine intuitive geometric parameters which control profile thickness distribution, chord, offset, and stagger angle. Three-dimensional finite element analysis of the blade is performed using ANSYS Mechanical software package. A sequential quadratic programming technique is used to solve the nonlinear optimization problem. Sensitivity analysis is performed using the finite-difference method. Several optimization problems with different objective functions and combinations of constraints are implemented. The aerodynamic constraints are not considered directly. The blade’s aerodynamic properties are sustained by imposing tight limits on the allowable changes of design variables. Sizing optimization is performed for an axial compressor blade of a gas turbine engine. The results show that the code can meet the defined objective and constraints for the most tested cases. A detailed comparison of optimized profiles with the baseline geometry is provided.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

scholarly journals The effect of the outlet angle β2 on the thermomechanical behavior of a centrifugal compressor blade

2020 ◽  
Vol 29 (1) ◽  
pp. 1-8
Author(s):  
Ahmed Allali ◽  
Sadia Belbachir ◽  
Ahmed Alami ◽  
Belhadj Boucham ◽  
Abdelkader Lousdad
Keyword(s):  
Mechanical Behavior ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Complex Form ◽  
Compressor Blade ◽  
Stress Fields ◽  
The Finite Element Method ◽  
Mechanical Fatigue ◽  
Outlet Angle ◽  
The Impact

AbstractThe objective of this work lies in the three-dimensional study of the thermo mechanical behavior of a blade of a centrifugal compressor. Numerical modeling is performed on the computational code "ABAQUS" based on the finite element method. The aim is to study the impact of the change of types of blades, which are defined as a function of wheel output angle β2, on the stress fields and displacements coupled with the variation of the temperature.This coupling defines in a realistic way the thermo mechanical behavior of the blade where one can note the important concentrations of stresses and displacements in the different zones of its complex form as well as the effects at the edges. It will then be possible to prevent damage and cracks in the blades of the centrifugal compressor leading to its failure which can be caused by the thermal or mechanical fatigue of the material with which the wheel is manufactured.

Three-Dimensional Flows and Loss Reduction in Axial Compressors

1987 ◽  
Vol 109 (3) ◽  
pp. 354-361 ◽  
Author(s):  
Y. Dong ◽  
S. J. Gallimore ◽  
H. P. Hodson
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Axial Flow ◽  
Tracer Gas ◽  
Suction Surface ◽  
Axial Compressors ◽  
Small Clearance ◽  
Oil Flow ◽  
Stator Blade ◽  
Flow Compressor

Measurements have been performed in a low-speed high-reaction single-stage axial compressor. Data obtained within and downstream of the rotor, when correlated with the results of other investigations, provide a link between the existence of suction surface–hub corner separations, their associated loss mechanisms, and blade loading. Within the stator, it has been shown that introducing a small clearance between the stator blade and the stationary hub increases the efficiency of the stator compared to the case with no clearance. Oil flow visualizaton indicated that the leakage reduced the extensive suction surface–hub corner separation that would otherwise exist. A tracer gas experiment showed that the large radial shifts of the surface streamlines indicated by the oil flow technique were only present close to the blade. The investigation demonstrates the possible advantages of including hub clearance in axial flow compressor stator blade rows.

Compressor Performance 2D Modelling at Reverse Flow Conditions

2010 ◽  
Author(s):  
L. Gallar ◽  
I. Tzagarakis ◽  
V. Pachidis ◽  
R. Singh
Keyword(s):  
Experimental Data ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Engine Performance ◽  
Two Dimensional ◽  
Flow Conditions ◽  
Compressor Surge ◽  
Compressor Performance ◽  
Shaft Failure

After a shaft failure the compression system of a gas turbine is likely to surge due to the heavy vibrations induced on the engine after the breakage. Unlike at any other conditions of operation, compressor surge during a shaft over-speed event is regarded as desirable as it limits the air flow across the engine and hence the power available to accelerate the free turbine. It is for this reason that the proper prediction of the engine performance during a shaft over-speed event claims for an accurate modelling of the compressor operation at reverse flow conditions. The present study investigates the ability of the existent two dimensional algorithms to simulate the compressor performance in backflow conditions. Results for a three stage axial compressor at reverse flow were produced and compared against stage by stage experimental data published by Gamache. The research shows that due to the strong radial fluxes present over the blades, two dimensional approaches are inadequate to provide satisfactory results. Three dimensional effects and inaccuracies are accounted for by the introduction of a correction parameter that is a measure of the pressure loss across the blades. Such parameter is tailored for rotors and stators and enables the satisfactory agreement between calculations and experiments in a stage by stage basis. The paper concludes with the comparison of the numerical results with the experimental data supplied by Day on a four stage axial compressor.

Improving a one-dimensional centrifugal compressor performance prediction method

2005 ◽  
Vol 219 (8) ◽  
pp. 653-659 ◽  
Author(s):  
E Swain
Keyword(s):  
Centrifugal Compressor ◽  
Performance Prediction ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Prediction Method ◽  
Compressor Cascade ◽  
One Dimensional ◽  
Compressor Performance ◽  
Cfd Analyses

A one-dimensional centrifugal compressor performance prediction technique that has been available for some time is updated as a result of extracting the component performance from three-dimensional computational fluid dynamic (CFD) analyses. Confidence in the CFD results is provided by comparison of overall performance for one of the compressor examples. The extracted impeller characteristic is compared with the original impeller loss model, and this indicated that some improvement was desirable. The position of least impeller loss was determined using a traditional axial compressor cascade method, and suitable algebraic expressions were derived to match the CFD data. The merit of the approach lies with the relative ease that CFD component performance currently can be achieved and adjusting one-dimensional methods to agree with the CFD-derived models.

Sign in / Sign up

Export Citation Format

Share Document