Three-dimensional laminar boundary-layer transition on a sharp 8 degcone at Mach 10

AIAA Journal ◽  
1970 ◽  
Vol 8 (5) ◽  
pp. 852-856 ◽  
Author(s):  
V. DICRISTINA
Keyword(s):  
Boundary Layer ◽  
Laminar Boundary Layer ◽  
Three Dimensional ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Mach 10

Automatic control of laminar boundary-layer transition

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 85-90
Author(s):  
P. A. Nelson ◽  
M. C. M. Wright ◽  
J.-L. Rioual
Keyword(s):  
Boundary Layer ◽  
Automatic Control ◽  
Laminar Boundary Layer ◽  
Boundary Layer Transition ◽  
Layer Transition

Keel Design for Low Viscous Drag

1987 ◽  
Author(s):  
Clifford J. Obara ◽  
C. P. van Dam
Keyword(s):  
Boundary Layer ◽  
Laminar Flow ◽  
Laminar Boundary Layer ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Viscous Drag ◽  
Hydrodynamic Characteristics ◽  
Sweep Angle ◽  
Layer Transition ◽  
Layer Flow

In this paper, foil and planform parameters which govern the level of viscous drag produced by the keel of a sailing yacht are discussed. It is shown that the application of laminar boundary-Layer flow offers great potential for increased boat speed resulting from the reduction in viscous drag. Three foil shapes have been designed and it is shown that their hydro­dynamic characteristics are very much dependent on location and mode of boundary-Layer transition. The planform parameter which strongly affects the capabilities of the keel to achieve laminar flow is lea ding-edge sweep angle. The two significant phenomena related to keel sweep angle which can cause premature transition of the laminar boundary layer are crossflow instability and turbulent contamination of the leading-edge attachment line. These flow phenomena and methods to control them are discussed in detail. The remaining factors that affect the maintainability of laminar flow include surface roughness, surface waviness, and freestream turbulence. Recommended limits for these factors are given to insure achievability of laminar flow on the keel. In addition, the application of a simple trailing-edge flap to improve the hydrodynamic characteristics of a foil at moderate-to-high leeway angles is studied.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

The Critical Height of Distributed Roughness to Cause Boundary Layer Transition

1959 ◽  
Vol 63 (588) ◽  
pp. 722-722
Author(s):  
R. L. Dommett
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Laminar Boundary Layer ◽  
Boundary Layer Transition ◽  
Critical Height ◽  
Layer Transition ◽  
Local Conditions ◽  
Additional Advantage ◽  
Boundary Layer Equations ◽  
General Method

It has been found that there is a critical height for “sandpaper” type roughness below which no measurable disturbances are introduced into a laminar boundary layer and above which transition is initiated at the roughness. Braslow and Knox have proposed a method of predicting this height, for flow over a flat plate or a cone, using exact solutions of the laminar boundary layer equations combined with a correlation of experimental results in terms of a Reynolds number based on roughness height, k, and local conditions at the top of the elements. A simpler, yet more general, method can be constructed by taking additional advantage of the linearity of the velocity profile near the wall in a laminar boundary layer.

Sign in / Sign up

Export Citation Format

Share Document