Three-Dimensional Navier-Stokes Simulations of Turbine Rotor-Stator Interaction; Part I1 - Results

1989 ◽  
Vol 5 (3) ◽  
pp. 312-319 ◽  
Author(s):  
Man Mohan Rai
Keyword(s):  
Three Dimensional ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Rotor Stator Interaction

Three-Dimensional Navier-Stokes Analysis of Turbine Rotor and Tip-Leakage Flowfield

1997 ◽  
Author(s):  
J. Luo ◽  
B. Lakshminarayana
Keyword(s):  
Three Dimensional ◽  
Turbine Rotor ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

The 3-D viscous flowfield in the rotor passage of a single-stage turbine, including the tip-leakage flow, is computed using a Navier-Stokes procedure. A grid-generation code has been developed to obtain embedded H grids inside the rotor tip gap. The blade tip geometry is accurately modeled without any “pinching”. Chien’s low-Reynolds-number k-ε model is employed for turbulence closure. Both the mean-flow and turbulence transport equations are integrated in time using a four-stage Runge-Kutta scheme. The computational results for the entire turbine rotor flow, particularly the tip-leakage flow and the secondary flows, are interpreted and compared with available data. The predictions for major features of the flowfield are found to be in good agreement with the data. Complicated interactions between the tip-clearance flows and the secondary flows are examined in detail. The effects of endwall rotation on the development and interaction of secondary and tip-leakage vortices are also analyzed.

scholarly journals Computation of Flow Past a Turbine Blade With and Without Tip Clearance

1991 ◽  
Author(s):  
W. R. Briley ◽  
D. V. Roscoe ◽  
H. J. Gibeling ◽  
R. C. Buggeln ◽  
J. S. Sabnis ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Main Stream ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Gas Generator

Three-dimensional solutions of the ensemble-averaged Navier-Stokes equations have been computed for a high-turning turbine rotor passage, both with and without tip clearance effects. The geometry is Pratt & Whitney’s preliminary design for the Generic Gas Generator Turbine (GGGT), having an axial chord of 0.5 inch and turning angle of about 160 degrees. The solutions match the design Reynolds number of 3x 106/inch and design inflow/outflow distributions of flow quantities. The grid contains 627,000 points, including 20 radial points in the clearance gap of 0.015 inch, and has a minimum spacing of 10−4 inch adjacent to all surfaces. The solutions account for relative motion of the blade and shroud surfaces and include a backstep on the shroud. Computed results are presented which show the general flow behavior, especially near the tip clearance and backstep regions. The results are generally consistent with experimental observations for other geometries having thinner blades and smaller turning angles. The leakage flow includes some fluid originally in the freestream at 91 percent span. Downstream, the leakage flow behaves as a wall jet directed at 100 degrees to the main stream, with total pressure and temperature higher than the freestream. Radial distributions of circumferentially-averaged flow quantities are compared for solutions with and without tip leakage flow. Two-dimensional solutions are also presented for the mid-span blade geometry for design and off-design inflow angles.

Physics-Based Part Orientation and Sentencing: A Solution to Manufacturing Variability

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Wen Yao Lee ◽  
William N. Dawes ◽  
John D. Coull
Keyword(s):  
Three Dimensional ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Performance Control ◽  
Turbine Rotor Blade ◽  
Geometric Tolerancing ◽  
Performance Variability ◽  
Geometric Tolerances ◽  
Aero Engine ◽  
Part Orientation

Abstract Casting deviations introduce geometric variability that impacts the aerodynamic performance of turbomachinery. These effects are studied for a high-pressure turbine rotor blade from a modern aero-engine. A sample of 197 blades were measured using structured-light three-dimensional scanning, and the performance of each blade is quantified using Reynolds-averaged Navier–Stokes (RANS) simulations. Casting variation is typically managed by applying geometric tolerances to determine the suitability of a component for service. The analysis demonstrates that this approach may not be optimal since it does not necessarily align with performance, in particular the capacity and efficiency. Alternatively, functional acceptance based on the predicted performance of each blade removes the uncertainty associated with geometric tolerancing and gives better performance control. Building on these findings, the paper proposes a method to set the orientation of the fir-tree, which is machined after casting. By customizing the alignment of each blade, performance variability and scrap rates can be significantly reduced. The method uses predictions of performance to reorient the castings to compensate for manufacturing-induced errors, without changing the design-intent blade geometry and with minimal changes to the manufacturing facility.

Potential Flow Field Generated by Downstream Moving Bars and Propagated on a Turbine Blade at Low Reynolds Number

2011 ◽  
Author(s):  
Ve´ronique Penin ◽  
Pascale Kulisa ◽  
Franc¸ois Bario
Keyword(s):  
Boundary Layer ◽  
Large Scale ◽  
Numerical Study ◽  
Three Dimensional ◽  
Potential Effect ◽  
Navier Stokes ◽  
Turbine Cascade ◽  
Wake Interaction ◽  
Rotor Stator Interaction ◽  
The Stability

During the last few decades, the size and weight of turbo-machinery have been continuously reduced. However, by decreasing the distance between rows, rotor-stator interaction is strengthened. Two interactions now have the same magnitude: wake interaction and potential effect. Studying this effect is essential to understand rotor-stator interactions. Indeed, this phenomenon influences the whole flow, including the boundary layer of the upstream and downstream blades, ergo the stability of the flow and the efficiency of the machine. A large scale turbine cascade followed by a specially designed rotating cylinder system is used. Synchronised velocity LDA measurements on the vane profile show the flow and boundary layer behavior due to the moving bars. To help the general understanding and to corroborate our experimental results, numerical investigations are carried out with an unsteady three dimensional Navier-Stokes code. Moreover, the numerical study informs about the potential disturbance to the whole flow of the cascade.

Sign in / Sign up

Export Citation Format

Share Document