Gas turbine engine disk cyclic life prediction

1975 ◽  
Vol 12 (4) ◽  
pp. 360-365 ◽  
Author(s):  
S. A. Sattar ◽  
C. V. Sundt
Keyword(s):  
Gas Turbine ◽  
Life Prediction ◽  
Gas Turbine Engine ◽  
Cyclic Life ◽  
Turbine Engine

Modeling of Cyclic Life for Compressor Rotor of Gas Turbine Engine Taking Into Account Production Deviations

2020 ◽  
Author(s):  
Alexandr N. Arkhipov ◽  
Yury A. Ravikovich ◽  
Anton A. Matushkin ◽  
Dmitry P. Kholobtsev
Keyword(s):  
Gas Turbine ◽  
Low Cycle Fatigue ◽  
Probabilistic Modeling ◽  
Gas Turbine Engine ◽  
Critical Zone ◽  
Design Stage ◽  
Cyclic Life ◽  
Engine Operation ◽  
Turbine Engine ◽  
Compressor Rotor

Abstract The regional aircraft with a turbofan gas turbine engine, created in Russia, is successfully operated in the world market. Further increase of the life and reduction of the cost of the life cycle are necessary to ensure the competitive advantages of the engine. One of the units limiting the engine life is the compressor rotor. The cyclic life of the rotor depends on many factors: the stress-strain state in critical zones, the life of the material under low-cycle loading, the regime of engine operation, production deviations (within tolerances), etc. In order to verify the influence of geometry deviations, the calculations of the model with nominal dimensions and the model with the most unfavorable geometric dimensions (worst cases) have been carried out. The obtained influence coefficients for geometric and weight tolerances are then used for probabilistic modeling of stresses in the critical zone. Rotor speed and gas loads on the blades for different flight missions and engine wear are determined from the corresponding aerodynamic calculations taking into account the actual flight cycles (takeoff, reduction, reverse) and are also used for stress recalculations. The subsequent calculation of the rotor cyclic life and the resource assessment is carried out taking into account the spread of the material low-cycle fatigue by probabilistic modeling of the rotor geometry and weight loads. A preliminary assessment of the coefficients of tolerances influence on stress in the critical zone can be used to select the optimal (in terms of life) tolerances at the design stage. Taking into account the actual geometric and weight parameters can allow estimating the stress and expected life of each manufactured rotor.

Probabilistic Treatment of Crack Nucleation and Growth for Gas Turbine Engine Materials

2010 ◽  
Vol 132 (8) ◽  
Author(s):  
M. P. Enright ◽  
R. C. McClung ◽  
S. J. Hudak ◽  
W. L. Francis
Keyword(s):  
Gas Turbine ◽  
Life Prediction ◽  
Crack Nucleation ◽  
Gas Turbine Engine ◽  
Nucleation And Growth ◽  
Smooth Specimen ◽  
Growth Phases ◽  
Adequate Treatment ◽  
Turbine Engine ◽  
Crack Nucleation And Growth

The empirical models commonly used for probabilistic life prediction do not provide adequate treatment of the physical parameters that characterize fatigue damage development. For these models, probabilistic treatment is limited to statistical analysis of strain-life regression fit parameters. In this paper, a model is proposed for life prediction that is based on separate nucleation and growth phases of total fatigue life. The model was calibrated using existing smooth specimen strain-life data, and it has been validated for other geometries. Crack nucleation scatter is estimated based on the variability associated with smooth specimen and fatigue crack growth data, including the influences of correlation among crack nucleation and growth phases. The influences of crack nucleation and growth variability on life and probability of fracture are illustrated for a representative gas turbine engine disk geometry.

A New Finite Element Approach to Biaxial Fatigue Life Prediction in Gas Turbine Engine

2010 ◽  
Author(s):  
Wasim Tarar ◽  
M.-H. Herman Shen
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Gas Turbine ◽  
Life Prediction ◽  
Gas Turbine Engine ◽  
Constitutive Law ◽  
Fatigue Life Prediction ◽  
Turbine Engine ◽  
Number Of Cycles ◽  
Cycles To Failure

High cycle fatigue is the most common cause of failure in gas turbine engines. Different design tools have been developed to predict number of cycles to failure for a component subjected to fatigue loads. An energy-based fatigue life prediction framework was previously developed in recent research for prediction of axial and bending fatigue life at various stress ratios. The framework for the prediction of fatigue life via energy analysis was based on a new constitutive law, which states the following: the amount of energy required to fracture a material is constant. A finite element approach for uniaxial and bending fatigue was developed by authors based on this constitutive law. In this study, the energy expressions that construct the new constitutive law are integrated into minimum potential energy formulation to develop a new QUAD-4 finite element for fatigue life prediction. The newly developed QUAD-4 element is further modified to obtain a plate element. The Plate element can be used to model plates subjected to biaxial fatigue including bending loads. The new QUAD-4 element is benchmarked with previously developed uniaxial tension/compression finite element. The comparison of Finite element method (FEM) results to existing experimental fatigue data, verifies the new finite element development for fatigue life prediction. The final output of this finite element analysis is in the form of number of cycles to failure for each element in ascending or descending order. Therefore, the new finite element framework can predict the number of cycles to failure at each location in gas turbine engine structural components. The new finite element provides a very useful tool for fatigue life prediction in gas turbine engine components. The performance of the fatigue finite element is demonstrated by the fatigue life predictions from Al6061-T6 aluminum and Ti-6Al-4V. Results are compared with experimental results and analytical predictions.

A New Hex-8 Finite Element for Gas Turbine Engine Fatigue Life Prediction

2011 ◽  
Author(s):  
Wasim Tarar ◽  
M.-H. Herman Shen
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Gas Turbine ◽  
Life Prediction ◽  
Gas Turbine Engine ◽  
Constitutive Law ◽  
Fatigue Life Prediction ◽  
Turbine Engine ◽  
Number Of Cycles ◽  
Cycles To Failure

High cycle fatigue is the major governing failure mode in aerospace structures and gas turbine engines. Different design tools are available to predict number of cycles to failure for a component subjected to fatigue loads. An energy-based fatigue life prediction framework was previously developed in recent research for prediction of axial, bending and torsional fatigue life at various stress ratios. The framework for the prediction of fatigue life via energy analysis was based on a new constitutive law, which states the following: the amount of energy required to fracture a material is constant. A 1-D ROD element for unixial fatigue, a BEAM element for bending fatigue and a QUAD-4 element for biaxial fatigue were developed by authors based on this constitutive law. In this study, the energy expressions that construct the new constitutive law are integrated into minimum potential energy formulation to develop a new HEX-8 BRICK finite element for fatigue life prediction. The newly developed HEX-8 BRICK element has 8 nodes and each node has 3 degrees of freedom (DOF) in x, y and z directions. This element is further modified to add the rotational and bending DOFs for application to real world three dimensional (3D) structures and components. HEX-8 BRICK fatigue finite element has capability to predict the number of cycles to failure for 3-D objects subjected to multiaxial stresses. The new HEX-8 element is benchmarked with previously developed uniaxial tension/compression finite element in order to verify the new development. The comparison of finite element method (FEM) results to existing experimental fatigue data, verifies the new finite element development for fatigue life prediction. The final output of this finite element analysis is in the form of number of cycles to failure for each element in ascending or descending order. Therefore, the new finite element framework can predict the number of cycles to failure at each location in gas turbine engine structural components. The new finite element provides a very useful tool for fatigue life prediction in gas turbine engine components as it provides a complete picture of fatiguing process. The performance of the HEX-8 fatigue finite element is demonstrated by comparison of life prediction results for A16061-T6 to previously developed multiaxial fatigue life prediction approach by the authors. Another set of comparison is made to results for type 304 stainless steel data.

Damage Tolerance Based Life Prediction in Gas Turbine Engine Blades Under Vibratory High Cycle Fatigue

1997 ◽  
Vol 119 (1) ◽  
pp. 143-146 ◽  
Author(s):  
D. P. Walls ◽  
R. E. deLaneuville ◽  
S. E. Cunningham
Keyword(s):  
Stress Intensity ◽  
Fracture Mechanics ◽  
Gas Turbine ◽  
Life Prediction ◽  
High Cycle Fatigue ◽  
Damage Tolerance ◽  
Gas Turbine Engine ◽  
Cycle Fatigue ◽  
Turbine Engine ◽  
Aspect Ratios

A novel fracture mechanics approach has been used to predict crack propagation lives in gas turbine engine blades subjected to vibratory high cycle fatigue (HCF). The vibratory loading included both a resonant mode and a nonresonant mode, with one blade subjected to only the nonresonant mode and another blade to both modes. A life prediction algorithm was utilized to predict HCF propagation lives for each case. The life prediction system incorporates a boundary integral element (BIE) derived hybrid stress intensity solution, which accounts for the transition from a surface crack to corner crack to edge crack. It also includes a derivation of threshold crack length from threshold stress intensity factors to give crack size limits for no propagation. The stress intensity solution was calibrated for crack aspect ratios measured directly from the fracture surfaces. The model demonstrates the ability to correlate predicted missions to failure with values deduced from fractographic analysis. This analysis helps to validate the use of fracture mechanics approaches for assessing damage tolerance in gas turbine engine components subjected to combined steady and vibratory stresses.

scholarly journals Damage Tolerance Based Life Prediction in Gas Turbine Engine Blades Under Vibratory High Cycle Fatigue

1995 ◽  
Author(s):  
David P. Walls ◽  
Robert E. deLaneuville ◽  
Susan E. Cunningham
Keyword(s):  
Stress Intensity ◽  
Fracture Mechanics ◽  
Gas Turbine ◽  
Life Prediction ◽  
High Cycle Fatigue ◽  
Damage Tolerance ◽  
Resonant Mode ◽  
Gas Turbine Engine ◽  
Cycle Fatigue ◽  
Turbine Engine

A novel fracture mechanics approach has been used to predict crack propagation lives in gas turbine engine blades subjected to vibratory high cycle fatigue (HCF). The vibratory loading included both a resonant mode and a non-resonant mode, with one blade subjected to only the non-resonant mode and another blade to both modes. A life prediction algorithm was utilized to predict HCF propagation lives for each case. The life prediction system incorporates a boundary integral element (BIE) derived hybrid stress intensity solution which accounts for the transition from a surface crack to corner crack to edge crack. It also includes a derivation of threshold crack length from threshold stress intensity factors to give crack size limits for no propagation. The stress intensity solution was calibrated for crack aspect ratios measured directly from the fracture surfaces. The model demonstrates the ability to correlate predicted missions to failure with values deduced from fractographic analysis. This analysis helps to validate the use of fracture mechanics approaches for assessing damage tolerance in gas turbine engine components subjected to combined steady and vibratory stresses.

Probabilistic Treatment of Crack Nucleation and Growth for Gas Turbine Engine Materials

2006 ◽  
Author(s):  
M. P. Enright ◽  
R. C. McClung ◽  
S. J. Hudak ◽  
W. L. Francis
Keyword(s):  
Gas Turbine ◽  
Life Prediction ◽  
Crack Nucleation ◽  
Gas Turbine Engine ◽  
Nucleation And Growth ◽  
Smooth Specimen ◽  
Growth Phases ◽  
Adequate Treatment ◽  
Turbine Engine ◽  
Crack Nucleation And Growth

The empirical models commonly used for probabilistic life prediction do not provide adequate treatment of the physical parameters that characterize fatigue damage development. For these models, probabilistic treatment is limited to statistical analysis of strain-life regression fit parameters. In this paper, a model is proposed for life prediction that is based on separate nucleation and growth phases of total fatigue life. The model was calibrated using existing smooth specimen strain-life data, and has been validated for other geometries. Crack nucleation scatter is estimated based on the variability associated with smooth specimen and fatigue crack growth data, including the influences of correlation among crack nucleation and growth phases. The influences of crack nucleation and growth variability on life and probability of fracture is illustrated for a representative gas turbine engine disk geometry.

Sign in / Sign up

Export Citation Format

Share Document