Oscillatory control of separation at high Reynolds numbers

AIAA Journal ◽  
1999 ◽  
Vol 37 ◽  
pp. 1062-1071 ◽  
Author(s):  
A. Seifert ◽  
L. G. Pack
Keyword(s):  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds

TRANSONIC CROSS FLOW (M∞ = 0.8) OVER A CIRCULAR CYLINDER AT HIGH REYNOLDS NUMBERS

2012 ◽  
Vol 43 (5) ◽  
pp. 589-613
Author(s):  
Vyacheslav Antonovich Bashkin ◽  
Ivan Vladimirovich Egorov ◽  
Ivan Valeryevich Ezhov ◽  
Sergey Vladimirovich Utyuzhnikov
Keyword(s):  
Circular Cylinder ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds

Turbulent vortex breakdown at high Reynolds numbers

AIAA Journal ◽  
2000 ◽  
Vol 38 ◽  
pp. 825-834
Author(s):  
F. Novak ◽  
T. Sarpkaya
Keyword(s):  
Vortex Breakdown ◽  
Reynolds Numbers ◽  
Turbulent Vortex ◽  
High Reynolds Numbers ◽  
High Reynolds

Drag Measurements on Long Thin Cylinders at Small Angles and High Reynolds Numbers

2004 ◽  
Author(s):  
William L. Keith ◽  
Kimberly M. Cipolla ◽  
David R. Hart ◽  
Deborah A. Furey
Keyword(s):  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

On the drag force of bubbles in bubble swarms at intermediate and high Reynolds numbers

2011 ◽  
Vol 66 (14) ◽  
pp. 3204-3211 ◽  
Author(s):  
I. Roghair ◽  
Y.M. Lau ◽  
N.G. Deen ◽  
H.M. Slagter ◽  
M.W. Baltussen ◽  
...  
Keyword(s):  
Drag Force ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds

Effects of Reynolds Number and Free-Stream Turbulence on Boundary Layer Transition in a Compressor Cascade

2000 ◽  
Author(s):  
Heinz-Adolf Schreiber ◽  
Wolfgang Steinert ◽  
Bernhard Küsters
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
High Reynolds Numbers ◽  
High Turbulence ◽  
High Reynolds

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0×106 and turbulence intensities from about 0.7 to 4%. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35–40% of chord. For high turbulence levels (Tu > 3%) and high Reynolds numbers transition propagates upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably and at Tu = 4% bypass transition is observed near 7–10% of chord. Experimental results are compared to theoretical predictions using the transition model which is implemented in the MISES code of Youngren and Drela. Overall the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers.

Oscillatory Control of Separation at High Reynolds Numbers

AIAA Journal ◽  
10.2514/2.834 ◽  
1999 ◽  
Vol 37 (9) ◽  
pp. 1062-1071 ◽  
Author(s):  
A. Seifert ◽  
L. G. Pack
Keyword(s):  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds
Sign in / Sign up

Export Citation Format

Share Document