Investigation of the influence of blowing and combustion on turbulent wall boundary layers

AIAA Journal ◽  
1989 ◽  
Vol 27 (3) ◽  
pp. 370-372 ◽  
Author(s):  
Clemet Yam ◽  
Harry Dwyer
Keyword(s):  
Boundary Layers ◽  
Wall Boundary ◽  
Turbulent Wall

Experiments on Flame Flashback in a Quasi-2D Turbulent Wall Boundary Layer for Premixed Methane-Hydrogen-Air Mixtures

2010 ◽  
Author(s):  
Christian Eichler ◽  
Thomas Sattelmayer
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Turbulent Flows ◽  
Turbulent Transport ◽  
Wall Friction ◽  
Evaluation Procedure ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Flame Flashback ◽  
Turbulent Wall

Premixed combustion of hydrogen-rich mixtures involves the risk of flame flashback through wall boundary layers. For laminar flow conditions, the flashback mechanism is well understood and is usually correlated by a critical velocity gradient at the wall. Turbulent transport inside the boundary layer considerably increases the flashback propensity. Only tube burner setups have been investigated in the past and thus turbulent flashback limits were only derived for a fully-developed Blasius wall friction profile. For turbulent flows, details of the flame propagation in proximity to the wall remain unclear. This paper presents results from a new experimental combustion rig, apt for detailed optical investigations of flame flashbacks in a turbulent wall boundary layer developing on a flat plate and being subject to an adjustable pressure gradient. Turbulent flashback limits are derived from the observed flame position inside the measurement section. The fuels investigated cover mixtures of methane, hydrogen and air at various mixing ratios. The associated wall friction distributions are determined by RANS computations of the flow inside the measurement section with fully resolved boundary layers. Consequently, the interaction between flame back pressure and incoming flow is not taken into account explicitly, in accordance with the evaluation procedure used for tube burner experiments. The results are compared to literature values and the critical gradient concept is reviewed in light of the new data.

Influence of Reynolds number on characteristics of turbulent wall boundary layers

1984 ◽  
Vol 2 (1) ◽  
pp. 7-16 ◽  
Author(s):  
J. Andreopoulos ◽  
F. Durst ◽  
Z. Zaric ◽  
J. Jovanovic
Keyword(s):  
Reynolds Number ◽  
Boundary Layers ◽  
Wall Boundary ◽  
Turbulent Wall

Experiments on Flame Flashback in a Quasi-2D Turbulent Wall Boundary Layer for Premixed Methane-Hydrogen-Air Mixtures

2010 ◽  
Vol 133 (1) ◽  
Author(s):  
Christian Eichler ◽  
Thomas Sattelmayer
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Turbulent Flows ◽  
Turbulent Transport ◽  
Wall Friction ◽  
Evaluation Procedure ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Flame Flashback ◽  
Turbulent Wall

Premixed combustion of hydrogen-rich mixtures involves the risk of flame flashback through wall boundary layers. For laminar flow conditions, the flashback mechanism is well understood and is usually correlated by a critical velocity gradient at the wall. Turbulent transport inside the boundary layer considerably increases the flashback propensity. Only tube burner setups were investigated in the past, and thus turbulent flashback limits were only derived for a fully developed Blasius wall friction profile. For turbulent flows, details of the flame propagation in proximity to the wall remain unclear. This paper presents results from a new experimental combustion rig, apt for detailed optical investigations of flame flashbacks in a turbulent wall boundary layer developing on a flat plate and being subject to an adjustable pressure gradient. Turbulent flashback limits are derived from the observed flame position inside the measurement section. The fuels investigated cover mixtures of methane, hydrogen, and air at various mixing ratios. The associated wall friction distributions are determined by Reynolds-averaged Navier-Stokes (RANS) computations of the flow inside the measurement section with fully resolved boundary layers. Consequently, the interaction between flame back pressure and incoming flow is not taken into account explicitly, in accordance with the evaluation procedure used for tube burner experiments. The results are compared with literature values, and the critical gradient concept is reviewed in light of the new data.

Applicability of Taylor’s hypothesis in rough- and smooth-wall boundary layers

2016 ◽  
Vol 812 ◽  
pp. 398-417 ◽  
Author(s):  
D. T. Squire ◽  
N. Hutchins ◽  
C. Morrill-Winter ◽  
M. P. Schultz ◽  
J. C. Klewicki ◽  
...  
Keyword(s):  
Boundary Layers ◽  
Outer Region ◽  
Rough Wall ◽  
Turbulent Shear ◽  
Normal Velocity ◽  
Turbulent Shear Flow ◽  
Smooth Wall ◽  
Wall Boundary ◽  
Taylor’S Hypothesis ◽  
Velocity Spectra

The spatial structure of smooth- and rough-wall boundary layers is examined spectrally at approximately matched friction Reynolds number ($\unicode[STIX]{x1D6FF}^{+}\approx 12\,000$). For each wall condition, temporal and true spatial descriptions of the same flow are available from hot-wire anemometry and high-spatial-range particle image velocimetry, respectively. The results show that over the resolved flow domain, which is limited to a streamwise length of twice the boundary layer thickness, true spatial spectra of smooth-wall streamwise and wall-normal velocity fluctuations agree, to within experimental uncertainty, with those obtained from time series using Taylor’s frozen turbulence hypothesis (Proc. R. Soc. Lond. A, vol. 164, 1938, pp. 476–490). The same applies for the streamwise velocity spectra on rough walls. For the wall-normal velocity spectra, however, clear differences are observed between the true spatial and temporally convected spectra. For the rough-wall spectra, a correction is derived to enable accurate prediction of wall-normal velocity length scales from measurements of their time scales, and the implications of this correction are considered. Potential violations to Taylor’s hypothesis in flows above perturbed walls may help to explain conflicting conclusions in the literature regarding the effect of near-wall modifications on outer-region flow. In this regard, all true spatial and corrected spectra presented here indicate structural similarity in the outer region of smooth- and rough-wall flows, providing evidence for Townsend’s wall-similarity hypothesis (The Structure of Turbulent Shear Flow, vol. 1, 1956).

Exhaust plumes from nozzles with wall boundary layers.

1968 ◽  
Vol 5 (10) ◽  
pp. 1143-1147 ◽  
Author(s):  
FREDERICK P. BOYNTON
Keyword(s):  
Boundary Layers ◽  
Wall Boundary ◽  
Exhaust Plumes

Extended Models for Transitional Rough Wall Boundary Layers With Heat Transfer: Part I—Model Formulations

2008 ◽  
Author(s):  
M. Stripf ◽  
A. Schulz ◽  
H.-J. Bauer ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Boundary Layers ◽  
Turbulence Model ◽  
Turbulence Intensity ◽  
Discrete Element ◽  
Rough Wall ◽  
Test Cases ◽  
Wall Boundary ◽  
Turbine Vane

Two extended models for the calculation of rough wall transitional boundary layers with heat transfer are presented. Both models comprise a new transition onset correlation, which accounts for the effects of roughness height and density, turbulence intensity and wall curvature. In the transition region, an intermittency equation suitable for rough wall boundary layers is used to blend between the laminar and fully turbulent state. Finally, two different submodels for the fully turbulent boundary layer complete the two models. In the first model, termed KS-TLK-T in this paper, a sand roughness approach from Durbin et al., which builds upon a two-layer k-ε-turbulence model, is used for this purpose. The second model, the so-called DEM-TLV-T model, makes use of the discrete-element roughness approach, which was recently combined with a two-layer k-ε-turbulence model by the present authors. The discrete element model will be formulated in a new way suitable for randomly rough topographies. Part I of the paper will provide detailed model formulations as well as a description of the database used for developing the new transition onset correlation. Part II contains a comprehensive validation of the two models, using a variety of test cases with transitional and fully turbulent boundary layers. The validation focuses on heat transfer calculations on both, the suction and the pressure side of modern turbine airfoils. Test cases include extensive experimental investigations on a high-pressure turbine vane with varying surface roughness and turbulence intensity, recently published by the current authors as well as new experimental data from a low-pressure turbine vane. In the majority of cases, the predictions from both models are in good agreement with the experimental data.

Sign in / Sign up

Export Citation Format

Share Document