High-Lift Devices for a Delta Wing Installed Around a Trailing-Edge

2003 ◽  
Vol 40 (5) ◽  
pp. 932-937 ◽  
Author(s):  
Koji Miyaji ◽  
Tomoyuki Arasawa
Keyword(s):  
Delta Wing ◽  
Trailing Edge ◽  
High Lift

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

Effects of a vectored trailing edge jet on delta wing vortex breakdown

2003 ◽  
Vol 34 (5) ◽  
pp. 651-654 ◽  
Author(s):  
J. J. Wang ◽  
Q. S. Li ◽  
J. Y. Liu
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Trailing Edge

The Dassault Mirage G

1969 ◽  
Vol 73 (708) ◽  
pp. 1027-1028
Author(s):  
Henri Deplante
Keyword(s):  
Leading Edge ◽  
Variable Geometry ◽  
Relative Thickness ◽  
Trailing Edge ◽  
High Lift ◽  
Profound Knowledge ◽  
Subsonic Speed ◽  
Trailing Edge Flaps ◽  
Leading Edge Slats

The interest of wings with variable sweepback springs directly from pure commonsense and appeals to no profound knowledge of aerodynamics for its justification. To realise the advantage of variable geometry, it is enough to know that only a wing of small relative thickness is capable of good performance at supersonic speeds and that by increasing the sweepback from 20° to 70° the thickness of a wing is divided by about 2. In the advanced position, the wing offers its full span to the airstream and with high-lift devices in action (leading-edge slats and trailing-edge flaps combined), the aeroplane can develop the considerable lift necessary for take-off and landing as well as for break-through and for slow approach. Wings still advanced but slats, flaps and undercarriage retracted, the aeroplane is in excellent maximum fineness condition for protracted cruising at subsonic speed or for a long wait. As soon as transonic (Mach No of more than 0-8) or supersonic speeds are in question, the wings are progressively folded back.

Exploitation of Adaptive Trailing Edge Architectures to Small Aircraft

2017 ◽  
Author(s):  
Gianluca Amendola ◽  
Ignazio Dimino ◽  
Antonio Concilio ◽  
Rosario Pecora ◽  
Francesco Amoroso
Keyword(s):  
Design Development ◽  
Commercial Aircraft ◽  
Trailing Edge ◽  
High Lift ◽  
Large Size ◽  
Weight Variation ◽  
Weight Penalty ◽  
Structural Architecture ◽  
System Layout ◽  
Small Aircraft

Airfoil camber adaptation may be the key for the performance improvement of wings for many specific applications, including shorter take-off distance, compensation of weight variation and so on. Following the successful experiences gained in SARISTU, where an adaptive trailing edge device was developed for medium to large size commercial aircraft, the authors propose to exploit the developed architecture to a small aircraft wing. The basic reasons behind that mainly rely on the associated possibility to access easier implementation onto a real aircraft instead of referring to wing segments for wind tunnel or ground tests. In this way, many operative problems are faced, that would be otherwise neglected in usual lab experimentation. First of all, the integration of the proposed device onto a flying machine, that in turn pose the problem of facing the interface with the existing systems. Secondly, the necessity of including the device into the flap while fully preserving its current functionality. Furthermore, the necessity of developing a robust design process that allows having the release of the permit-to-fly. Each of the above steps, non-exhaustive in illustrating the difficulty of the addressed challenge, is structured in many other sub-segments, ranging from a suitable FHA analysis to a full re-design of the existing high lift systems or the adaptation of the architecture of the reference morphing trailing edge itself. This last item poses the classical challenge of the scaling issues, requiring the structural and the actuation subsystems to entirely fit into the new geometry. The objective of the present research is then to verify the feasibility of applying a certain architectural morphing philosophy onto a real aircraft, taking into account all the operational difficulties related to such an operation. This paper reports the activities related to the exploitation of the reference adaptive structural architecture, to the geometry of a flap of a small aircraft. In detail, the system layout is presented, followed by a FE analysis of the structural system under the operational loads and an estimation of the weight penalty associated to this transformation. Interfaces of the flap system with the main aircraft body are considered as constraints to the design development, so that the only flap is affected.

scholarly journals Design methodology for trailing-edge high-lift mechanisms

2016 ◽  
Vol 7 (4) ◽  
pp. 521-534 ◽  
Author(s):  
David Zaccai ◽  
Francesco Bertels ◽  
Roelof Vos
Keyword(s):  
Design Methodology ◽  
Trailing Edge ◽  
High Lift

160 Studies on High-Efficiency LP Turbine : Effect of Trailing Edge Shape on High-Lift Condition

2014 ◽  
Vol 2014.49 (0) ◽  
pp. 117-118
Author(s):  
Yoshiaki EBINA ◽  
Ken-ichi FUNAZAKI ◽  
Takehiko KOSUGI ◽  
Hiroki KANEDA
Keyword(s):  
High Efficiency ◽  
Trailing Edge ◽  
High Lift ◽  
Lp Turbine
Sign in / Sign up

Export Citation Format

Share Document