Modeling of Room-Temperature Heat Pipe Startup from the Frozen State

1997 ◽  
Vol 11 (2) ◽  
pp. 165-172 ◽  
Author(s):  
J. M. Ochterbeck
Keyword(s):  
Heat Pipe ◽  
Room Temperature ◽  
Temperature Heat ◽  
Frozen State

Modeling of room-temperature heat pipe startup from the frozen state

10.2514/3.875 ◽  
1997 ◽  
Vol 11 ◽  
pp. 165-172
Author(s):  
S. Rao ◽  
E. L. Mulkay ◽  
J. M. Ochterbeck
Keyword(s):  
Heat Pipe ◽  
Room Temperature ◽  
Temperature Heat ◽  
Frozen State

scholarly journals Direct measurement of the thermoelectric properties of electrochemically deposited Bi2Te3 thin films

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Jose Recatala-Gomez ◽  
Pawan Kumar ◽  
Ady Suwardi ◽  
Anas Abutaha ◽  
Iris Nandhakumar ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermoelectric Properties ◽  
Bismuth Telluride ◽  
Indium Tin Oxide ◽  
Seed Layer ◽  
Room Temperature ◽  
Low Cost ◽  
Temperature Dependent ◽  
Temperature Heat ◽  
Electrochemically Deposited

Abstract The best known thermoelectric material for near room temperature heat-to-electricity conversion is bismuth telluride. Amongst the possible fabrication techniques, electrodeposition has attracted attention due to its simplicity and low cost. However, the measurement of the thermoelectric properties of electrodeposited films is challenging because of the conducting seed layer underneath the film. Here, we develop a method to directly measure the thermoelectric properties of electrodeposited bismuth telluride thin films, grown on indium tin oxide. Using this technique, the temperature dependent thermoelectric properties (Seebeck coefficient and electrical conductivity) of electrodeposited thin films have been measured down to 100 K. A parallel resistor model is employed to discern the signal of the film from the signal of the seed layer and the data are carefully analysed and contextualized with literature. Our analysis demonstrates that the thermoelectric properties of electrodeposited films can be accurately evaluated without inflicting any damage to the films.

Experimental Study on Carbonization of Low-Rank Pulverized Coal with High Temperature Heat Pipe

2014 ◽  
Vol 953-954 ◽  
pp. 1035-1039
Author(s):  
Li Qun Wang ◽  
Zhong Bo Yi ◽  
Zhong Xiang Wei
Keyword(s):  
High Temperature ◽  
Heat Pipe ◽  
Pulverized Coal ◽  
Holding Time ◽  
Raw Material ◽  
Low Rank ◽  
Experimental Result ◽  
Operating Characteristics ◽  
Temperature Heat ◽  
High Temperature Heat Pipe

Aimed at improving the utilization of pulverized coal, high-temperature heat pipe technology was introduced into lignite carbonization.Under the design of power of 10kw semi-industrial pulverized coal carbonization test equipment, Fugu lignite coal as raw material to investigate the operating characteristics of the device and carbonization characteristics. Experimental result shows that the high temperature heat pipes heat steadily and meet the temperature requirement of low-temperature carbonization. With the extension of the holding time, the semi-coke fixed carbon content increasing, but volatile matter vice versa, however, holding time above 60 minutes, the effect of carbonization is not obvious, and the best carbonization time is 30 ~ 60 minutes. The length of the holding time has little effect on gas composition, the content of H2 and CH4 are relatively higher than the rest gas, (H2 + CH4) gas accounted for 70% of the total, the heating value remains at 18.76 ~ 19.22MJ/m3, belongs to medium-high value gas, could provide for industrial and civilian use.

Experiment study on thermal behavior of a horizontal high-temperature heat pipe under motion conditions

2022 ◽  
Vol 165 ◽  
pp. 108760
Author(s):  
Hao Sun ◽  
Xiao Liu ◽  
Haoyu Liao ◽  
Chenglong Wang ◽  
Jing Zhang ◽  
...  
Keyword(s):  
High Temperature ◽  
Thermal Behavior ◽  
Heat Pipe ◽  
Experiment Study ◽  
Temperature Heat ◽  
High Temperature Heat Pipe

The Structure and Properties of Boundaries in Bicrystals of Boron-Doped Ni3(Al,l at% Ta)

1990 ◽  
Vol 213 ◽  
Author(s):  
M. J. Mills ◽  
S. H. Goods ◽  
S. M. Foiles
Keyword(s):  
Room Temperature ◽  
Tensile Ductility ◽  
Al Alloy ◽  
Boron Doped ◽  
Transmission Electron ◽  
Temperature Heat ◽  
Atomistic Calculations ◽  
Rate Of Cooling ◽  
Temperature Heat Treatment ◽  
Ductile State

ABSTRACTThe effect of boron on the structure and macroscopic properties of an isolated grain boundary in bicrystals of a non-stoichiometric Ni3Al alloy (76 at% Ni, 23 at% Al, 1 at%Ta) has been studied. The room temperature tensile ductility and fracture mode of the bicrystals varies dramatically with the rate of cooling after elevated temperature heat treatment. In the absence of significant segregation of boron to the boundary, the bicrystals fail via brittle interfacial fracture with little or no ductility. When the segregation of boron to the boundary is maximized, the bicrystals are highly ductile. High resolution transmission electron microscopy reveals that this ductile state is achieved without the formation of a detectable region of compositional disorder at the boundary. Atomistic calculations using a Monte Carlo scheme predict that only partial disordering of the planes immediately adjacent to the boundary should occur for Ni-rich alloys both with and without boron. These results suggest that the presence of boron causes an increase in the cohesive energy of the boundaries rather than a change in the local compositional ordering.

Sign in / Sign up

Export Citation Format

Share Document