Pitch Rate and Reynolds Number Effects on Unsteady Boundary-Layer Transition and Separation

1998 ◽  
Vol 35 (1) ◽  
pp. 46-52 ◽  
Author(s):  
Scott J. Schreck ◽  
William E. Faller ◽  
Hank E. Helin
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Boundary Layer Transition ◽  
Unsteady Boundary Layer ◽  
Layer Transition ◽  
Reynolds Number Effects

An Experimental Study of Heat Transfer on an Outlet Guide Vane

2014 ◽  
Author(s):  
Chenglong Wang ◽  
Lei Wang ◽  
Bengt Sundén ◽  
Valery Chernoray ◽  
Hans Abrahamsson
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Turbulent Boundary Layer ◽  
Guide Vane ◽  
Incidence Angle ◽  
Boundary Layer Transition ◽  
Transfer Coefficients ◽  
Suction Surface ◽  
Layer Transition

In the present study, the heat transfer characteristics on the suction and pressure sides of an outlet guide vane (OGV) are investigated by using liquid crystal thermography (LCT) method in a linear cascade. Because the OGV has a complex curved surface, it is necessary to calibrate the LCT by taking into account the effect of viewing angles of the camera. Based on the calibration results, heat transfer measurements of the OGV were conducted. Both on- and off-design conditions were tested, where the incidence angles of the OGV were 25 degrees and −25 degrees, respectively. The Reynolds numbers, based on the axial flow velocity and the chord length, were 300,000 and 450,000. In addition, heat transfer on suction side of the OGV with +40 degrees incidence angle was measured. The results indicate that the Reynolds number and incidence angle have considerable influences upon the heat transfer on both pressure and suction surfaces. For on-design conditions, laminar-turbulent boundary layer transitions are on both sides, but no flow separation occurs; on the contrary, for off-design conditions, the position of laminar-turbulent boundary layer transition is significantly displaced downstream on the suction surface, and a separation occurs from the leading edge on the pressure surface. As expected, larger Reynolds number gives higher heat transfer coefficients on both sides of the OGV.

Velocity and Pressure Measurements Along a Row of Confined Cylinders

2006 ◽  
Author(s):  
Barton L. Smith ◽  
Jack J. Stepan ◽  
Donald M. McEligot
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Symmetry Plane ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Recirculation Region ◽  
Pressure Measurements ◽  
Layer Transition ◽  
Flow Experiments

The results of flow experiments performed in a cylinder array designed to mimic a VHTR Nuclear Plant lower plenum design are presented. Pressure drop and velocity field measurements were made. Based on these measurements, five regimes of behavior are identified that are found to depend on Reynolds number. It is found that the recirculation region behind the cylinders is shorter than that of half cylinders placed on the wall representing the symmetry plane. Unlike a single cylinder, the separation point is found to always be on the rear of the cylinders, even at very low Reynolds number. Boundary layer transition is found to occur at much lower Reynolds numbers than previously reported.

The Critical Height of Distributed Roughness to Cause Boundary Layer Transition

1959 ◽  
Vol 63 (588) ◽  
pp. 722-722
Author(s):  
R. L. Dommett
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Laminar Boundary Layer ◽  
Boundary Layer Transition ◽  
Critical Height ◽  
Layer Transition ◽  
Local Conditions ◽  
Additional Advantage ◽  
Boundary Layer Equations ◽  
General Method

It has been found that there is a critical height for “sandpaper” type roughness below which no measurable disturbances are introduced into a laminar boundary layer and above which transition is initiated at the roughness. Braslow and Knox have proposed a method of predicting this height, for flow over a flat plate or a cone, using exact solutions of the laminar boundary layer equations combined with a correlation of experimental results in terms of a Reynolds number based on roughness height, k, and local conditions at the top of the elements. A simpler, yet more general, method can be constructed by taking additional advantage of the linearity of the velocity profile near the wall in a laminar boundary layer.

Advanced infrared thermography data analysis for unsteady boundary layer transition detection

2019 ◽  
Vol 31 (1) ◽  
pp. 015301 ◽  
Author(s):  
C Mertens ◽  
C C Wolf ◽  
A D Gardner ◽  
F F J Schrijer ◽  
B W van Oudheusden
Keyword(s):  
Boundary Layer ◽  
Data Analysis ◽  
Infrared Thermography ◽  
Boundary Layer Transition ◽  
Unsteady Boundary Layer ◽  
Layer Transition
Sign in / Sign up

Export Citation Format

Share Document