Computational Optimization of Coanda Effect on Film-Cooling Performance

2015 ◽  
Vol 29 (4) ◽  
pp. 757-765 ◽  
Author(s):  
Mustapha Benabed
Keyword(s):  
Film Cooling ◽  
Coanda Effect ◽  
Cooling Performance ◽  
Computational Optimization ◽  
Coandǎ Effect

Flow attachment to solid surfaces: The Coanda effect

AIChE Journal ◽  
1972 ◽  
Vol 18 (1) ◽  
pp. 51-57 ◽  
Author(s):  
T. Panitz ◽  
D. T. Wasan
Keyword(s):  
Solid Surfaces ◽  
Coanda Effect ◽  
Coandǎ Effect

scholarly journals Comparison of CFD simulations and measurements of flow affected by coanda effect

2012 ◽  
Vol 25 ◽  
pp. 01015 ◽  
Author(s):  
Jan Fišer ◽  
Jan Jedelský ◽  
Tomáš Vach ◽  
Matěj Forman ◽  
Miroslav Jícha
Keyword(s):  
Coanda Effect ◽  
Cfd Simulations ◽  
Coandǎ Effect

Effusion-Cooling Performance at Gas Turbine Combustor Representative Flow Conditions

2012 ◽  
Author(s):  
Vinod U. Kakade ◽  
Steven J. Thorpe ◽  
Miklós Gerendás
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Conditions ◽  
Cooling Performance ◽  
Free Stream Turbulence ◽  
High Turbulence ◽  
Adiabatic Effectiveness

The thermal management of aero gas turbine engine combustion systems commonly employs effusion-cooling in combination with various cold-side convective cooling schemes. The combustor liner incorporates many small holes which are usually set in staggered arrays and at a shallow angle to the cooled surface; relatively cold compressor delivery air is then allowed to flow through these holes to provide the full-coverage film-cooling effect. The efficient design of such systems requires robust correlations of film-cooling effectiveness and heat transfer coefficient at a range of aero-thermal conditions, and the use of appropriately validated computational models. However, the flow conditions within a combustor are characterised by particularly high turbulence levels and relatively large length scales. The experimental evidence for performance of effusion-cooling under such flow conditions is currently sparse. The work reported here is aimed at quantifying typical effusion-cooling performance at a range of combustor relevant free-stream conditions (high turbulence), and also to assess the importance of modeling the coolant to free-stream density ratio. Details of a new laboratory wind-tunnel facility for the investigation of film-cooling at high turbulence levels are reported. For a typical combustor effusion geometry that uses cylindrical holes, spatially resolved measurements of adiabatic effectiveness, heat transfer coefficient and net heat flux reduction are presented for a range of blowing ratios (0.48 to 2), free-stream turbulence conditions (4 and 22%) and density ratios (0.97 and 1.47). The measurements reveal that elevated free-stream turbulence impacts on both the adiabatic effectiveness and heat transfer coefficient, although this is dependent upon the blowing ratio being employed and particularly the extent to which the coolant jets detach from the surface. At low blowing ratios the presence of high turbulence levels causes increased lateral spreading of the coolant adjacent to the injection points, but more rapid degradation in the downstream direction. At high blowing ratios, high turbulence levels cause a modest increase in effectiveness due to turbulent transport of the detached coolant fluid. Additionally, the augmentation of heat transfer coefficient caused by the coolant injection is seen to be increased at high free-stream turbulence levels.

Experimental and Numerical Study on the Effects of the Relative Position of Film Hole and Orientation Ribs on the Film Cooling With Ribbed Cross-Flow Coolant Channel

2020 ◽  
Author(s):  
Bingran Li ◽  
Cunliang Liu ◽  
Lin Ye ◽  
Huiren Zhu ◽  
Fan Zhang
Keyword(s):  
Heat Transfer ◽  
Relative Position ◽  
Film Cooling ◽  
Numerical Study ◽  
Cross Flow ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Numerical Studies

Abstract To investigate the application of ribbed cross-flow coolant channels with film hole effusion and the effects of the internal cooling configuration on film cooling, experimental and numerical studies are conducted on the effect of the relative position of the film holes and different orientation ribs on the film cooling performance. Three cases of the relative position of the film holes and different orientation ribs (post-rib, centered, and pre-rib) in two ribbed cross-flow channels (135° and 45° orientation ribs) are investigated. The film cooling performances are measured under three blowing ratios by the transient liquid crystal measurement technique. A RANS simulation with the realizable k-ε turbulence model and enhanced wall treatment is performed. The results show that the cooling effectiveness and the downstream heat transfer coefficient for the 135° rib are basically the same in the three position cases, and the differences between the local effectiveness average values for the three are no more than 0.04. The differences between the heat transfer coefficients are no more than 0.1. The “pre-rib” and “centered” cases are studied for the 45° rib, and the position of the structures has little effect on the film cooling performance. In the different position cases, the outlet velocity distribution of the film holes, the jet pattern and the discharge coefficient are consistent with the variation in the cross flow. The related research previously published by the authors showed that the inclination of the ribs with respect to the holes affects the film cooling performance. This study reveals that the relative positions of the ribs and holes have little effect on the film cooling performance. This paper expands and improves the study of the effect of the internal cooling configuration on film cooling and makes a significant contribution to the design and industrial application of the internal cooling channel of a turbine blade.

Sign in / Sign up

Export Citation Format

Share Document