Large-Eddy Simulations of a Cylindrical Film Cooling Hole

2013 ◽  
Vol 27 (2) ◽  
pp. 255-273 ◽  
Author(s):  
Perry L. Johnson ◽  
Jayanta S. Kapat
Keyword(s):  
Film Cooling ◽  
Large Eddy Simulations ◽  
Large Eddy ◽  
Cooling Hole

Large Eddy Simulations on Fan Shaped Film Cooling Hole with Upstream Boundary Layer Turbulence Effect Generated by Trip Strip

2021 ◽  
pp. 1-37
Author(s):  
Young Seok Kang ◽  
Sangook Jun ◽  
Dong-Ho Rhee
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Film Cooling ◽  
Main Flow ◽  
Large Eddy Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Large Eddy ◽  
Cooling Hole

Abstract Large eddy simulations on the well-known 7-7-7 fan shaped cooling hole were carried out. Like using a trip strip to create turbulent boundary layer in practical experiments, trip strips with different configurations were placed upstream of the cooling hole to investigate incoming turbulent boundary layer effect on the film cooling flow behavior. Without the trip, horseshoe vortex generated by laminar boundary layer induced laterally discharging cooling flow in the lateral direction. Meanwhile, the induced cooling flow formed high film cooling effectiveness region around the film cooling hole. When the incoming boundary flow was turbulent, laterally discharged cooling flow was influenced by the turbulent boundary layer to dissipate to the main flow and resultant high effectiveness region disappeared. Depending on the trip configuration, quantitative characteristics of boundary layer such as turbulent intensity, momentum thickness and shape factor were strongly affected. Some trip configurations resulted in fully developed turbulent boundary layer just before leading edge of the film cooling hole. In such cases, distribution of the film cooling effectiveness showed a reasonable agreement with available experimental data where the quantitative properties of the turbulent boundary layer were similar. However, when the trip was located too close to the film cooling hole, the separated and reattached flow did not develop into the stabilized turbulent boundary layer. Then strong turbulence intensity in the main flow boundary layer stimulated break down of the cooling flow vortex structure and early dissipation to the main flow. It resulted in restricted film cooling flow coverage.

Large Eddy Simulations on Fan Shaped Film Cooling Hole With Various Inlet Turbulence Generation Methods

2020 ◽  
Author(s):  
Young Seok Kang ◽  
Sangook Jun ◽  
Dong-Ho Rhee
Keyword(s):  
Vortex Structure ◽  
Film Cooling ◽  
Main Flow ◽  
Large Eddy Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Large Eddy ◽  
Cooling Hole ◽  
Turbulence Generation

Abstract Large eddy simulations on well-known 7-7-7 fan shaped cooling hole have been carried out. Film cooling methods are generally applied to high pressure turbine, of which flow condition is extremely turbulent because high pressure turbines are generally located downstream combustor in gas turbines. However, different to RANS simulations, implementing turbulence at the main flow inlet is not simple in LES. For this reason, several numerical techniques have been devised to give turbulence information at the inlet boundary condition in LES. In this study, rectangular turbulator was located in front of the cooling hole to generate turbulent boundary flow in the main flow. Another method used in this study is transient table method to simulate turbulent flow at the main flow inlet. Without turbulent velocity components in approaching flow, laterally discharged cooling flow touches wall while it forms a vortex structure. Then high film cooling effectiveness region around the cooling hole appears. In the meanwhile, when approaching flow is turbulent, the laterally discharged cooling flow no more forms vortex structure and dissipated to the main flow and resultant high effectiveness region disappears. Both turbulence generation methods showed that turbulent intensity of the main flow affects effective range of the cooling flow and resultant film cooling effectiveness distributions. Also high turbulence intensity of the main flow stimulates early break down of the vortex structure coming out of the cooling hole and its dissipation to the main flow. It means high turbulent intensity restricts film cooling flow coverage. Another lesson from the study is that vortex generated from the cooling hole, its development and dissipation to the main flow, have an important role to understand film cooling effectiveness distributions around the cooling hole.

scholarly journals Large Eddy Simulations on Film Cooling Flow Behaviors with Upstream Turbulent Boundary Layer Generated by Circular Cylinder

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 7227
Author(s):  
Young Seok Kang ◽  
Dong-Ho Rhee ◽  
Yu Jin Song ◽  
Jae Su Kwak
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Film Cooling ◽  
Measured Data ◽  
Large Eddy Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Large Eddy ◽  
Cooling Hole

Large eddy simulations on film cooling hole array on a flat plate was carried out to investigate upstream turbulence effect. Circular cylinders were configured to create a turbulent boundary layer and its diameter has been adjusted to generate 13% upstream turbulence intensity in the main flow. Due to the small pitch to diameter configuration of the cylinder, two-dimensional LES analysis was carried out in advance and the results showed that LES was an essential method to resolve flow field around and downstream circular cylinder, which was not available in RANS simulations. The three-dimensional LES results showed reasonable agreement in turbulence intensity and normalized velocity distributions along the vertical with measured data. According to the blowing ratio, the cooling flow coverage on the surface along the stream-wise direction was varied and well agreed with measured data. Additionally, upstream boundary flows were partially ingested inside the cooling hole and discharged again near along the centerline of the cooling hole. This accounted for film cooling effectiveness distribution inside the cooling hole surface and along the centerline. The current study revealed that the LES for predicting turbulent boundary layer behaviors due to upstream turbulence generation source was an effective and feasible method. Moreover, the LES effectively resolved flow fields such as film cooling flow behaviors and corresponding film cooling effectiveness distributions.

Large Eddy Simulations of Film-Cooling Flows With a Micro-Ramp Vortex Generator

2011 ◽  
Author(s):  
Aaron F. Shinn ◽  
S. Pratap Vanka
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Vortex Pair ◽  
Large Eddy Simulations ◽  
Wind Tunnel Experiments ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flows ◽  
Large Eddy

Large Eddy Simulations were performed to study the effect of a micro-ramp on an inclined turbulent jet interacting with a cross-flow in a film-cooling configuration. The micro-ramp vortex generator is placed downstream of the film-cooling jet. Changes in vortex structure and film-cooling effectiveness are evaluated and the genesis of the counter-rotating vortex pair in the jet is discussed. Results are reported with the jet modeled using a plenum/pipe configuration. This configuration was designed based on previous wind tunnel experiments at NASA Glenn Research Center, and the present results are meant to supplement those experiments. It is found that the micro-ramp improves film-cooling effectiveness by generating near-wall counter-rotating vortices which help entrain coolant from the jet and transport it to the surface. The pair of vortices generated by the micro-ramp are of opposite sense to the vortex pair embedded in the jet.

Film Cooling Using Antikidney Vortex Pairs: Effect of Blowing Conditions and Yaw Angle on Cooling and Losses

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Lars Gräf ◽  
Leonhard Kleiser
Keyword(s):  
Film Cooling ◽  
Vortex Pair ◽  
Diffusion Region ◽  
Jet Interaction ◽  
Physical Mechanisms ◽  
Large Eddy ◽  
Scaling Parameters ◽  
Cooling Hole ◽  
Single Jet ◽  
Yaw Angle

A film-cooling configuration generating an antikidney vortex pair is studied. The configuration features cylindrical cooling holes inclined at an angle of α=35  deg and arranged in two spanwise rows with row-wise alternating yaw angles ±β. Results of several large-eddy simulations are presented with varying blowing conditions and yaw angles. The effects on the achieved cooling and the generated losses are studied. The film-cooling Reynolds number (based on the fully turbulent hot boundary layer along a flat plate and the cooling hole diameter) is 6570 and the Mach number is 0.2. The density as well as mass-flux ratios (DR and M) range from 1 to 2 and the yaw angles from β=±30  deg to ±60  deg. We identify scaling parameters and explain relevant mechanisms. Moreover, the flow field is subdivided into three regions featuring different physical mechanisms: the single-jet, the jet-interaction, and the diffusion region. A strong antikidney vortex pair occurs for high momentum ratios I. For the highest ratio, I = 2.3, our configuration may provide even better effectiveness than cooling with particular fan-shaped holes.

Sign in / Sign up

Export Citation Format

Share Document