scholarly journals Correlation Analysis of High-Resolution Particle Image Velocimetry Data of Screeching Jets

AIAA Journal ◽  
2019 ◽  
Vol 57 (2) ◽  
pp. 735-748 ◽  
Author(s):  
D. J. Tan ◽  
D. Honnery ◽  
A. Kalyan ◽  
V. Gryazev ◽  
S. A. Karabasov ◽  
...  
Keyword(s):  
Particle Image Velocimetry ◽  
High Resolution ◽  
Correlation Analysis ◽  
Particle Image ◽  
Particle Image Velocimetry Data ◽  
Image Velocimetry

scholarly journals Data assimilation method to de-noise and de-filter particle image velocimetry data

2019 ◽  
Vol 877 ◽  
pp. 196-213 ◽  
Author(s):  
Jurriaan J. J. Gillissen ◽  
Roland Bouffanais ◽  
Dick K. P. Yue
Keyword(s):  
Particle Image Velocimetry ◽  
Data Assimilation ◽  
Particle Image ◽  
Particle Image Velocimetry Data ◽  
Reconstruction Error ◽  
Integration Time ◽  
Piv Measurement ◽  
Image Velocimetry ◽  
The Difference ◽  
Filter Particle

We present a variational data assimilation method in order to improve the accuracy of velocity fields $\tilde{\boldsymbol{v}}$, that are measured using particle image velocimetry (PIV). The method minimises the space–time integral of the difference between the reconstruction $\boldsymbol{u}$ and $\tilde{\boldsymbol{v}}$, under the constraint, that $\boldsymbol{u}$ satisfies conservation of mass and momentum. We apply the method to synthetic velocimetry data, in a two-dimensional turbulent flow, where realistic PIV noise is generated by computationally mimicking the PIV measurement process. The method performs optimally when the assimilation integration time is of the order of the flow correlation time. We interpret these results by comparing them to one-dimensional diffusion and advection problems, for which we derive analytical expressions for the reconstruction error.

High Resolution Particle Image Velocimetry and CH-PLIF Measurements and Analysis of a Shear Layer Stabilized Flame

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
C. W. Foley ◽  
I. Chterev ◽  
J. Seitzman ◽  
T. Lieuwen
Keyword(s):  
Particle Image Velocimetry ◽  
High Resolution ◽  
Shear Layer ◽  
Flow Velocity ◽  
Particle Image ◽  
Flame Stabilization ◽  
Flow Conditions ◽  
Local Flow ◽  
Image Velocimetry ◽  
Flow Velocities

Understanding the mechanisms and physics of flame stabilization and blowoff of premixed flames is critical toward the design of high velocity combustion devices. In the high bulk flow velocity situation typical of practical combustors, the flame anchors in shear layers where the local flow velocities are much lower. Within the shear layer, fluid strain deformation rates are very high and the flame can be subjected to significant stretch levels. The main goal of this work was to characterize the flow and stretch conditions that a premixed flame experiences in a practical combustor geometry and to compare these values to calculated extinction values. High resolution, simultaneous particle image velocimetry (PIV) and planar laser induced fluorescence of CH radicals (CH-PLIF) measurements are used to capture the flame edge and near-field stabilization region. When approaching lean limit extinction conditions, we note characteristic changes in the stretch and flow conditions experienced by the flame. Most notably, the flame becomes less critically stretched when fuel/air ratio is decreased. However, at these lean conditions, the flame is subject to higher mean flow velocities at the edge, suggesting less favorable flow conditions are present at the attachment point of the flame as blowoff is approached. These measurements suggest that blowoff of the flame from the shear layer is not directly stretch extinction induced, but rather the result of an imbalance between the speed of the flame edge and local tangential flow velocity.

Sign in / Sign up

Export Citation Format

Share Document