Steel Structure Impacting onto Water: Coupled Finite Element-Smoothed-Particle-Hydrodynamics Numerical Modeling

2011 ◽  
Vol 48 (4) ◽  
pp. 1299-1308 ◽  
Author(s):  
A. Grimaldi ◽  
D. J. Benson ◽  
F. Marulo ◽  
M. Guida
Keyword(s):  
Finite Element ◽  
Numerical Modeling ◽  
Smoothed Particle Hydrodynamics ◽  
Steel Structure ◽  
Particle Hydrodynamics ◽  
Smoothed Particle

NUMERICAL MODELING OF THE BALLISTIC LIMIT IN THE HYDRODYNAMIC RAM

2015 ◽  
Vol 76 (8) ◽  
Author(s):  
M. R. Aziz ◽  
W. Kuntjoro ◽  
N. V. David
Keyword(s):  
Finite Element ◽  
Numerical Modeling ◽  
Smoothed Particle Hydrodynamics ◽  
Ballistic Limit ◽  
Tank Wall ◽  
Rear Wall ◽  
Hydrodynamic Ram ◽  
Shock Phase ◽  
Particle Hydrodynamics ◽  
Smoothed Particle

This paper presents the ballistic limit study for the water-filled aluminum tank. The objective was to determine the ballistic limit for the rear tank wall by using numerical method. Commercial software Altair Hyperworks 12.0 was employed for this study. The finite element coupled with smoothed particle hydrodynamics (SPH) was developed to model the perforation of fragment simulating projectile (FSP) towards water-filled tank. Verification of the results was done by comparing with the experiment results. The results showed that there were four main phase failures occurred, which were shock phase, drag phase, cavitation phase and exit phase. The ballistic limit for the rear wall was 479.27 m/s.

Smoothed particle hydrodynamics versus finite element method for blast impact

2013 ◽  
Vol 61 (1) ◽  
pp. 111-121 ◽  
Author(s):  
T. Jankowiak ◽  
T. Łodygowski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Smoothed Particle Hydrodynamics ◽  
Concrete Slab ◽  
The Finite Element Method ◽  
Particle Hydrodynamics ◽  
Mesh Density ◽  
Smoothed Particle ◽  
Element Method

Abstract The paper considers the failure study of concrete structures loaded by the pressure wave due to detonation of an explosive material. In the paper two numerical methods are used and their efficiency and accuracy are compared. There are the Smoothed Particle Hydrodynamics (SPH) and the Finite Element Method (FEM). The numerical examples take into account the dynamic behaviour of concrete slab or a structure composed of two concrete slabs subjected to the blast impact coming from one side. The influence of reinforcement in the slab (1, 2 or 3 layers) is also presented and compared with a pure concrete one. The influence of mesh density for FEM and the influence of important parameters in SPH like a smoothing length or a particle distance on the quality of the results are discussed in the paper

A Parametric Study of the Modeling of Orthogonal Machining Using the Smoothed Particle Hydrodynamics Method

2015 ◽  
Author(s):  
Chinmay S. Avachat ◽  
Harish P. Cherukuri
Keyword(s):  
Finite Element ◽  
Smoothed Particle Hydrodynamics ◽  
Chip Morphology ◽  
Machining Processes ◽  
Orthogonal Machining ◽  
Particle Hydrodynamics ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Smoothed Particle ◽  
1045 Steel

Modeling machining processes with conventional finite element methods (FEM) is challenging due to the severe deformations that occur during machining, complex frictional conditions that exist between the cutting tool and the workpiece, and the possibility of self contact due to chip curling. Recently, the Smoothed Particle Hydrodynamics (SPH) method has emerged as a potential alternative for modeling machining processes due to its ability to handle severe deformations while avoiding mass and energy losses encountered by traditional FEM. The method has been implemented in several commercial finite element packages such as ABAQUS and LS-DYNA for solving problems involving localized severe deformations. Numerous control parameters are present in a typical SPH formulation. The purpose of this work is to evaluate the effect of the three most important parameters, namely, the smoothing length, particle density, and the type of SPH formulation. The effects of these parameters on the chip morphology and stress distribution in the context of orthogonal machining of AISI 1045 steel are investigated. The LS-DYNA finite element package along with Johnson-Cook material model is used for this purpose. Results from the parametric study are presented and compared with the previously reported results in the literature. In addition, the sensitivity of chip morphology and stresses to Johnson-Cook parameters for AISI 1045 steel is also investigated by considering five different sets of values reported in the literature for this steel.

scholarly journals Realistic computer modelling of stent retriever thrombectomy: a hybrid finite-element analysis-smoothed particle hydrodynamics model

2021 ◽  
Vol 18 (185) ◽  
Author(s):  
S. Mostafa Mousavi J. S. ◽  
Danial Faghihi ◽  
Kelsey Sommer ◽  
Mohammad M. S. Bhurwani ◽  
Tatsat R. Patel ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Smoothed Particle Hydrodynamics ◽  
Computer Modelling ◽  
Blood Clot ◽  
Stent Retriever ◽  
Element Analysis ◽  
Hybrid Finite Element ◽  
Particle Hydrodynamics ◽  
Smoothed Particle

Stent retriever thrombectomy is a pre-eminent treatment modality for large vessel ischaemic stroke. Simulation of thrombectomy could help understand stent and clot mechanics in failed cases and provide a digital testbed for the development of new, safer devices. Here, we present a novel, in silico thrombectomy method using a hybrid finite-element analysis (FEA) and smoothed particle hydrodynamics (SPH). Inspired by its biological structure and components, the blood clot was modelled with the hybrid FEA–SPH method. The Solitaire self-expanding stent was parametrically reconstructed from micro-CT imaging and was modelled as three-dimensional finite beam elements. Our simulation encompassed all steps of mechanical thrombectomy, including stent packaging, delivery and self-expansion into the clot, and clot extraction. To test the feasibility of our method, we simulated clot extraction in simple straight vessels. This was compared against in vitro thrombectomies using the same stent, vessel geometry, and clot size and composition. Comparisons with benchtop tests indicated that our model was able to accurately simulate clot deflection and penetration of stent wires into the clot, the relative movement of the clot and stent during extraction, and clot fragmentation/embolus formation. In this study, we demonstrated that coupling FEA and SPH techniques could realistically model stent retriever thrombectomy.

Sign in / Sign up

Export Citation Format

Share Document