Strut Injectors for Scramjets: Total Pressure Losses in Two Streamwise Vortex Interactions

2017 ◽  
Vol 33 (5) ◽  
pp. 1140-1150 ◽  
Author(s):  
Fabrizio Vergine ◽  
Cody Ground ◽  
Luca Maddalena
Keyword(s):  
Total Pressure ◽  
Streamwise Vortex ◽  
Pressure Losses ◽  
Vortex Interactions

scholarly journals Aerodynamic Losses in Turbines with and without Film Cooling, as Influenced by Mainstream Turbulence, Surface Roughness, Airfoil Shape, and Mach Number

2012 ◽  
Vol 2012 ◽  
pp. 1-28 ◽  
Author(s):  
Phil Ligrani
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Film Cooling ◽  
Total Pressure ◽  
High Speed ◽  
Density Ratio ◽  
Aerodynamic Loss ◽  
Pressure Losses ◽  
Loss Coefficients ◽  
Exit Mach Number

The influences of a variety of different physical phenomena are described as they affect the aerodynamic performance of turbine airfoils in compressible, high-speed flows with either subsonic or transonic Mach number distributions. The presented experimental and numerically predicted results are from a series of investigations which have taken place over the past 32 years. Considered are (i) symmetric airfoils with no film cooling, (ii) symmetric airfoils with film cooling, (iii) cambered vanes with no film cooling, and (iv) cambered vanes with film cooling. When no film cooling is employed on the symmetric airfoils and cambered vanes, experimentally measured and numerically predicted variations of freestream turbulence intensity, surface roughness, exit Mach number, and airfoil camber are considered as they influence local and integrated total pressure losses, deficits of local kinetic energy, Mach number deficits, area-averaged loss coefficients, mass-averaged total pressure loss coefficients, omega loss coefficients, second law loss parameters, and distributions of integrated aerodynamic loss. Similar quantities are measured, and similar parameters are considered when film-cooling is employed on airfoil suction surfaces, along with film cooling density ratio, blowing ratio, Mach number ratio, hole orientation, hole shape, and number of rows of holes.

Effect of Divergence Angle on Flow Through Inlet Section of Diffuser of a Gas Turbine Combustion Chamber: The CFD Approach

2006 ◽  
Author(s):  
Digvijay B. Kulshreshtha ◽  
S. A. Channiwala ◽  
Jitendra Chaudhary ◽  
Zoeb Lakdawala ◽  
Hitesh Solanki ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Total Pressure ◽  
Divergence Angle ◽  
Velocity Head ◽  
Turbine Engine ◽  
Inlet Velocity ◽  
Pressure Losses ◽  
Flow Through ◽  
Mach Numbers

In the combustor inlet diffuser section of gas turbine engine, high-velocity air from compressor flows into the diffuser, where a considerable portion of the inlet velocity head PT3 − PS3 is converted to static pressure (PS) before the airflow enters the combustor. Modern high through-flow turbine engine compressors are highly loaded and usually have high inlet Mach numbers. With high compressor exit Mach numbers, the velocity head at the compressor exit station may be as high as 10% of the total pressure. The function of the diffuser is to recover a large proportion of this energy. Otherwise, the resulting higher total pressure loss would result in a significantly higher level of engine specific fuel consumption. The diffuser performance must also be sensitive to inlet velocity profiles and geometrical variations of the combustor relative to the location of the pre-diffuser exit flow path. Low diffuser pressure losses with high Mach numbers are more rapidly achieved with increasing length. However, diffuser length must be short to minimize engine length and weight. A good diffuser design should have a well considered balance between the confliction requirements for low pressure losses and short engine lengths. The present paper describes the effect of divergence angle on diffuser performance for gas turbine combustion chamber using Computational Fluid Dynamic Approach. The flow through the diffuser is numerically solved for divergence angles ranging from 5 to 25°. The flow separation and formation of wake regions are studied.

Investigation of Variated Unsteady Inflow Boundary Conditions on the Transition Behavior of a Low Pressure Turbine Cascade Family

2014 ◽  
Author(s):  
Franz F. Blaim ◽  
Roland E. Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Condition ◽  
Transport Equation ◽  
Flow Separation ◽  
Total Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Number Range ◽  
Pressure Losses ◽  
Low Pressure Turbine ◽  
Transition Behavior

The objective of this paper is to analyze the influence of incoming periodic wakes, considering the variable width, on the integral total pressure loss for two low pressure turbine (LPT) airfoils. In order to reduce the overall weight of a LPT, the pitch to chord ratio was continuously increased, during the past decades. However, this increase encourages the development of the transition phenomena or even flow separation on the suction side of the blade. At low Reynolds numbers, large separation bubbles can occur there, which are linked with high total pressure losses. The incoming wakes of the upstream blades are known to trigger early transition, leading to a reduced risk of flow separation and hence minor integral total pressure losses caused by separation. For the further investigation of these effects, different widths of the incoming wakes will be examined in detail, here. This variation is carried out by using the numerical Unsteady Reynolds Averaged Solver TRACE developed by the DLR Cologne in collaboration with MTU Aero Engines AG. For the variation of the width of the wakes, a variable boundary condition was modeled, which includes the wake vorticity parameters. The width of the incoming wakes was used as the relevant variable parameter. The implemented boundary condition models the unsteady behavior of the incoming wakes by the variation of the velocity profile, using a prescribed frequenc. TRACE can use two different transition models; the main focus here is set to the γ–Reθt transition model, which uses local variables in a transport equation, to trigger the transition within the turbulence transport equation system. The experimental results were conducted at the high speed cascade open loop test facility at the Institute for Jet Propulsion at the University of the German Federal Armed Forces in Munich. For the investigation presented here, two LPT profiles — which were designed with a similar inlet angle, turning, and pitch are analyzed. However, with a common exit Mach number and a similar Reynolds number range between 40k and 400k, one profile is front loaded and the other one is aft loaded. Numerical unsteady results are in good agreement with the conducted measurements. The influence of the width of the wake on the time resolved transition behavior, represented by friction coefficient plots and momentum loss thickness will be analyzed in this paper.

scholarly journals Numerical and Experimental Analysis of Secondary Flow in Modern State-of-the-Art Low Pressure Guide Vane Rows

1995 ◽  
Author(s):  
Ernst Lindner
Keyword(s):  
Aspect Ratio ◽  
Secondary Flow ◽  
Total Pressure ◽  
Guide Vane ◽  
Numerical Results ◽  
Flow Behaviour ◽  
Inlet Guide Vane ◽  
Streamwise Vorticity ◽  
Pressure Losses ◽  
Turbine Guide Vane

To enhance the performance of the inlet guide vane and the annular duct of a jet engine, a detailed investigation of annular cascades with two different types of turbine guide vane rows is made. The first one is a leaned guide vane with an aspect ratio of two and a half and a transition duct ahead of the vane. To avoid the losses associated to the decelerating transition duct an alternative vane is designed and investigated with the same inlet and exit conditions. In this case the chord of the vane is increased to the effect that the vane begins immediately at the enterance of the diverging annulus and so a continuously accelerated flow is achieved. To maintain a good performance for this configuration a bowed-type vane with an aspect ratio of one is designed. The aim of the investigation is to obtain detailed informations on the secondary flow behaviour with particular regard to the development of the total pressure losses and the streamwise vorticity of the vortices inside and behind the blade rows. In the first step a three-dimensional, structured, explicit finite-volume flow-solver with a k–ε turbulence model is validated against the measurements, which were made in cross-sections behind the blades. Having proved that the numerical results are very close to the experimental ones, the secondary flow behaviour inside and behind the blade rows is analysed in the second step. By calculating the streamwise vorticity from the numerical results the formation of horse-shoe vortex, passage-vortex and the trailing edge vortex shed is investigated. The differences of the vortical motion and the formation of the total pressure losses between the two configurations of turbine guide vane rows are discussed.

The Effective Positions to Inject Water Into the Cascade of Compressor

2012 ◽  
Author(s):  
Jie Wang ◽  
Qun Zheng ◽  
Lanxin Sun ◽  
Mingcong Luo
Keyword(s):  
Kinetic Energy ◽  
Total Pressure ◽  
Lower Energy ◽  
Water Injection ◽  
Adverse Pressure Gradient ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Pressure Losses ◽  
Ansys Cfx ◽  
Highly Loaded

Generally, droplets are injected into air at inlet or interstage of a compressor. However, both cases did not consider how to utilize the kinetic energy of these moving droplets. Under the adverse pressure gradient of compressor, the lower energy fluids of blade surfaces and endwalls boundary layers would accumulate and separate. Kinetic droplets could accelerate the lower energy fluids and eliminate the separation. This paper mainly investigate the effective positions where to inject water and how to utilize the droplets’ kinetic energy. Four different injecting positions, which located on the suction surface and endwall, are chosen. The changes of vortexes in the compressor cascade are discussed carefully. In addition, the influences of water injection on temperature, total pressure losses and Mach number are analyzed. Numerical simulations are performed for a highly loaded compressor cascade with ANSYS CFX software.

Combustion Turbine Exhaust Duct, Silencer, and Stack Scale Modeling

2021 ◽  
Author(s):  
Robert Craven ◽  
Keith Kirkpatrick ◽  
Stephen Idem
Keyword(s):  
Reynolds Number ◽  
Power Plant ◽  
Pressure Loss ◽  
Total Pressure ◽  
Exhaust System ◽  
Total Pressure Loss ◽  
Scale Model ◽  
Pressure Losses ◽  
Exhaust Duct ◽  
On Line

Abstract After constructing a scale model of planned changes to a power plant exhaust system, tests were performed to measure pressure losses in the transition, silencer, and stack. A dimension of 0.30 m (1.0 ft) for the scale model corresponded to 3.7 m (12.0 ft) at full scale. To the extent possible, the scale model tests exhibited geometric similarity with the actual power plant. Total pressure loss coefficients varied between 2.122, 1.969, and 1.932, for three separate scale model configurations that were considered. A combination of turning vanes and splitter vanes in the five-gore elbow, coupled with the use of turning vanes in the rectangular elbow yielded the lowest total pressure loss. Although Reynolds number similarity between the scale model experiments and the actual power plant was not attained, Reynolds number independence was achieved in the tests. The results from this study was applied to model pressure loss in the actual power plant. The scale model testing revealed that utilization of the exhaust ducting design designated as Case A would yield a sufficiently low pressure loss that it would not degrade the performance of the combustion turbine in the power plant to be repaired. Therefore it was selected for inclusion in the retro-fitting of the power plant to facilitate its being quickly brought back on-line.

Production and Development of Secondary Flows and Losses in Two Types of Straight Turbine Cascades: Part 1—A Stator Case

1987 ◽  
Vol 109 (2) ◽  
pp. 186-193 ◽  
Author(s):  
A. Yamamoto
Keyword(s):  
Secondary Flow ◽  
Total Pressure ◽  
Experimental Information ◽  
Secondary Flows ◽  
Accumulation Process ◽  
Flow Angle ◽  
Turning Angle ◽  
Pressure Losses ◽  
Flow Vectors ◽  
Turbine Cascades

The present study intends to give some experimental information on secondary flows and on the associated total pressure losses occurring within turbine cascades. Part 1 of the paper describes the mechanism of production and development of the loss caused by secondary flows in a straight stator cascade with a turning angle of about 65 deg. A full representation of superimposed secondary flow vectors and loss contours is given at fourteen serial traverse planes located throughout the cascade. The presentation shows the mechanism clearly. Distributions of static pressures and of the loss on various planes close to blade surfaces and close to an endwall surface are given to show the loss accumulation process over the surfaces of the cascade passage. Variation of mass-averaged flow angle, velocity and loss through the cascade, and evolution of overall loss from upstream to downstream of the cascade are also given. Part 2 of the paper describes the mechanism in a straight rotor cascade with a turning angle of about 102 deg.

scholarly journals Cold Flow Computations for the Diffuser-Combustor Section of an Industrial Gas Turbine

1996 ◽  
Author(s):  
Dadong Zhou ◽  
Ting Wang ◽  
William R. Ryan
Keyword(s):  
Gas Turbine ◽  
Total Pressure ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Complex Flow ◽  
Pressure Losses ◽  
Structured Grid ◽  
Computational Fluid Dynamics Cfd ◽  
Enhance Efficiency ◽  
Industrial Gas Turbine

In the first part of a multipart project to analyze and optimize the complex three-dimensional diffuser-combustor section of a highly advanced industrial gas turbine under development, a computational fluid dynamics (CFD) analysts has been conducted. The commercial FEA code I-DEAS was used to complete the three-dimensional solid modeling and the structured grid generation. The flow calculation was conducted using the commercial CFD code PHOENICS. The multiblock method was employed to enhance computational capabilities. The mechanisms of the total pressure losses and possible ways to enhance efficiency by reducing the total pressure losses were examined. Mechanisms that contribute to the nonuniform velocity distribution of flow entering the combustor were also identified. The CFD results were informative and provided insight to the complex flow patterns in the reverse flow dump diffuser, however, the results are qualitative and are useful primarily as guidelines for optimization as opposed to firm design configuration selections.

Adjoint Based Aerodynamic Optimization of a Multi-Splitter Turbine Vane Frame

2019 ◽  
Author(s):  
Vincenzo Russo ◽  
Simone Orsenigo ◽  
Lasse Mueller ◽  
Tom Verstraete ◽  
Sergio Lavagnoli
Keyword(s):  
Total Pressure ◽  
Low Pressure ◽  
Design Parameters ◽  
Structural Constraints ◽  
Aerodynamic Optimization ◽  
Pressure Losses ◽  
Turbine Vane ◽  
Gradient Based ◽  
Adjoint Approach ◽  
Multi Body

Abstract This work presents a 2D optimization of a multi-body turbine vane frame (TVF), a particular configuration that can lead to considerable shortening of the aero-engine shaft as well as weight reduction. Traditionally, the turbine vane frame is used to guide the flow from the high pressure (HP) turbine to the low pressure (LP) turbine. Current designs have a mid turbine frame equipped with non lifting bodies that have structural and servicing functions, while multi-body configurations are characterized by the fact that, in order to shorten the duct length, the mid turbine struts are merged with the LP stator vanes, traditionally located downstream. This design architecture consists therefore of a multi-body vane row, where lifting long-chord struts replace some of the low pressure vane airfoils. However, the bulky struts cause significant aerodynamics losses and penalize the aerodynamics of the small vanes. The objective of the present work is to numerically optimize a TVF geometry with multi-body architecture using a gradient based algorithm coupled with the adjoint approach, enabling the use of a rich design space. Steady-state CFD simulations have been used to this end. The aim of this study is to reduce the total pressure losses of the TVF, while imposing several aerodynamic and structural constraints. The parametrization of the TVF geometry represents the airfoil shapes and their relative pitch-wise positions. The outcome of the optimization is to evaluate the potential improvements introduced by the optimized TVF geometry and to quantify the influence of the different design parameters on the total pressure losses.

Sign in / Sign up

Export Citation Format

Share Document