Aspects of Low- and High-Frequency Actuation for Aerodynamic Flow Control

AIAA Journal ◽  
2005 ◽  
Vol 43 (7) ◽  
pp. 1501-1511 ◽  
Author(s):  
Ari Glezer ◽  
Michael Amitay ◽  
Andrew M. Honohan
Keyword(s):  
Flow Control ◽  
High Frequency ◽  
Aerodynamic Flow Control

Interaction Phenomena of High Frequency Pulsed Blowing in LP Turbine-Like Boundary Layers at High Speed Test Conditions

2018 ◽  
Author(s):  
Valentin Bettrich ◽  
Martin Bitter ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Boundary Layer Flow ◽  
High Frequency ◽  
Active Flow Control ◽  
Suction Side ◽  
Operating Point ◽  
Layer Flow ◽  
Lp Turbine ◽  
Active Flow

The use of fluidic oscillators for active flow control applications is a proven and efficient concept. For the well-known highly loaded LP turbine profile T161, the total pressure losses could already reduced by 40% at low Reynolds numbers, were usually flow separation occurs. For further improvements of the active flow control concept, it is essential to understand the driving flow phenomena responsible for the loss reduction mechanism, which are discussed in this paper. The results presented are based on experimental investigations on a flat plate with pressure gradient, imposed with an aerodynamically highly loaded low pressure turbine suction side flow and equipped with active flow control. The analogy to the suction side of the T161 is shown and validated against former cascade measurements. Based on the T161 equivalent operating point of Re = 70,000 and a theoretical out flow Mach number of Ma2,th = 0.6, the focus is set on the interaction of the boundary layer flow with high frequency actuation. The chosen actuator, a high frequency coupled fluidic oscillator, is designed to independently adjust mass flow and frequency. The flat plate is equipped with an array of high frequency actuators to control the flow separation. For this study one oscillator operating point at 6.7kHz is presented and the influence on transition and loss reduction compared to the non-actuated case is discussed. This oscillator operating point was found to be most efficient and the steady and unsteady mixing behavior of the high frequency actuator impact and the low pressure turbine like suction side boundary layer flow is investigated in much detail. Depending on the measurement technique, the isentropic Mach number distribution, frequency spectra, standard deviation, skewness and kurtosis are evaluated. The most important results are on the one hand, that the chosen concept is more efficient compared to former studies in means of mass flow investment, which is mainly based on the chosen oscillator outlet position and frequency. On the other hand, in a transonic flow the mixing and interaction of the high frequency pulses and the boundary layer flow require about 10% of the surface length to even establish and about to 30% to be completed. These results of the mixing behavior between actuator and boundary layer for compressible flow conditions help to attain a fundamental understanding for future designs of active flow control concepts.

FLOW CONTROL AND MECHANISM FOR SLENDER BODY AT HIGH ANGLE OF ATTACK

2005 ◽  
Vol 19 (28n29) ◽  
pp. 1571-1574 ◽  
Author(s):  
XIAO MING ◽  
YUNSONG GU
Keyword(s):  
Flow Control ◽  
High Frequency ◽  
Angle Of Attack ◽  
Control Technique ◽  
High Angle ◽  
Dynamic Measurements ◽  
Wind Tunnel Experiments ◽  
Rolling Angle ◽  
High Angle Of Attack ◽  
Side Force

The wind tunnel experiments for high angle of attack aerodynamics were designed from the inspiration of understanding the mechanism and development of an innovative flow control technique. The side force, varying with the different rolling angle, is featured by bi-stable situation, and can be easily switched by a tiny disturbance. A miniature strake is attached to the nose tip of the model. When the strake is stationary, the direction of the side force can be controlled. When the nose tip strake, as an unsteady control means, is swung the flow pattern could be controlled. The results obtained from dynamic measurements of section side force indicate that when the strake swing at lower frequency the side force can follow the cadence of the swinging strake. With increasing frequency, the magnitude of the side force decreases. At still high frequency, the side force diminishes to zero. The side forces could be also changed proportionally. Based on the experimental factors, the mechanism of the asymmetry is discussed.

Sign in / Sign up

Export Citation Format

Share Document