Computational Study on the Critical Nozzle Flow of High-Pressure Hydrogen Gas

2008 ◽  
Vol 24 (4) ◽  
pp. 715-721 ◽  
Author(s):  
Jae-hyung Kim ◽  
Heuy-dong Kim ◽  
Toshiaki Setoguchi ◽  
Sigeru Matsuo
Keyword(s):  
High Pressure ◽  
Computational Study ◽  
Hydrogen Gas ◽  
Nozzle Flow ◽  
Critical Nozzle ◽  
Pressure Hydrogen

Numerical Study on Characteristics of High-Pressure Hydrogen Gas Flow in a Critical Nozzle

2019 ◽  
Vol 2019.72 (0) ◽  
pp. D15
Author(s):  
Shigeru MATSUO ◽  
Yusuke FUKUSHIMA ◽  
Kazuki NIIBAYASHI ◽  
Toshihiro MORIOKA ◽  
Naoya SAKODA ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Flow ◽  
Numerical Study ◽  
Hydrogen Gas ◽  
Critical Nozzle ◽  
Pressure Hydrogen

scholarly journals 813 Characteristics of High-Pressure Hydrogen Gas Flow in a Critical Nozzle

2013 ◽  
Vol 2013.66 (0) ◽  
pp. 259-260
Author(s):  
Junji NAGAO ◽  
Shigeru MATUO ◽  
Shotaro SUETSUGU ◽  
Toshiaki SETOGUCHI ◽  
Masanori MONDE
Keyword(s):  
High Pressure ◽  
Gas Flow ◽  
Hydrogen Gas ◽  
Critical Nozzle ◽  
Pressure Hydrogen

A study of the critical nozzle for flow rate measurement of high-pressure hydrogen gas

2007 ◽  
Vol 16 (1) ◽  
pp. 28-32 ◽  
Author(s):  
H. D. Kim ◽  
J. H. Lee ◽  
K. A. Park ◽  
T. Setoguchi ◽  
S. Matsuo
Keyword(s):  
High Pressure ◽  
Flow Rate ◽  
Hydrogen Gas ◽  
Rate Measurement ◽  
Flow Rate Measurement ◽  
Critical Nozzle ◽  
Pressure Hydrogen

scholarly journals Proposal of Design Method Enabling Cr-Mo Steels to be Used in High-Pressure Hydrogen Gas Environment

Hyomen Kagaku ◽  
2015 ◽  
Vol 36 (11) ◽  
pp. 562-567
Author(s):  
Hisao MATSUNAGA ◽  
Junichiro YAMABE ◽  
Saburo MATSUOKA
Keyword(s):  
High Pressure ◽  
Design Method ◽  
Hydrogen Gas ◽  
Gas Environment ◽  
Pressure Hydrogen

Crack Growth Analysis of High-Pressure Equipment for Hydrogen Storage

2013 ◽  
Author(s):  
Z. Y. Li ◽  
C. L. Zhou ◽  
Y. Z. Zhao ◽  
Z. L. Hua ◽  
L. Zhang ◽  
...  
Keyword(s):  
High Pressure ◽  
Hydrogen Storage ◽  
Crack Growth ◽  
Growth Analysis ◽  
Model Material ◽  
Hydrogen Gas ◽  
Cycle Life ◽  
Cold Worked ◽  
Type 304 ◽  
Pressure Hydrogen

Crack growth analysis (CGA) was applied to estimate the cycle life of the high-pressure hydrogen equipment constructed by the practical materials of 4340 (two heats), 4137, 4130X, A286, type 316 (solution-annealed (SA) and cold-worked (CW)), and type 304 (SA and CW) in 45, 85 and 105 MPa hydrogen and air. The wall thickness was calculated following five regulations of the High Pressure Gas Safety Institute of Japan (KHK) designated equipment rule, KHKS 0220, TSG R0002, JB4732, and ASME Sec. VIII, Div. 3. We also applied CGA for four typical model materials to discuss the effect of ultimate tensile strength (UTS), pressure and hydrogen sensitivity on the cycle life of the high-pressure hydrogen equipment. Leak before burst (LBB) was confirmed in all practical materials in hydrogen and air. The minimum KIC required for LBB of the model material with UTS of even 1500 MPa was 170 MPa·m0.5 in 105 MPa. Cycle life qualified 103 cycles for all practical materials in air. In 105 MPa hydrogen, the cycle life by KIH was much shorter than that in air for two heats of 4340 and 4137 sensitive to hydrogen gas embrittlement (HGE). The cycle life of type 304 (SA) sensitive to HGE was almost above 104 cycles in hydrogen, while the cycle life of type 316 (SA and CW) was not affected by hydrogen and that of A286 in hydrogen was near to that in air. It was discussed that the cycle life increased with decreasing pressure or UTS in hydrogen. This behavior was due to that KIH increased or fatigue crack growth (FCG) decreased with decreasing pressure or UTS. The cycle life data of the model materials under the conditions of the pressure, UTS, KIH, FCG and regulations in both hydrogen and air were proposed quantitatively for materials selection for high-pressure hydrogen storage.

Sign in / Sign up

Export Citation Format

Share Document