Numerical Investigation of Plasma-Based Flow Control for Transitional Highly-Loaded Low-Pressure Turbine

AIAA Journal ◽  
2007 ◽  
Vol 45 (10) ◽  
pp. 2554-2564 ◽  
Author(s):  
Donald P. Rizzetta ◽  
Miguel R. Visbal
Keyword(s):  
Flow Control ◽  
Numerical Investigation ◽  
Low Pressure ◽  
Low Pressure Turbine ◽  
Highly Loaded

Numerical Study of Active Flow Control for a Transitional Highly Loaded Low-Pressure Turbine

2006 ◽  
Vol 128 (5) ◽  
pp. 956-967 ◽  
Author(s):  
Donald P. Rizzetta ◽  
Miguel R. Visbal
Keyword(s):  
Flow Control ◽  
Numerical Study ◽  
Active Flow Control ◽  
Low Pressure ◽  
Transitional Flow ◽  
Suction Surface ◽  
Low Pressure Turbine ◽  
Baseline Case ◽  
Active Flow ◽  
Highly Loaded

Active control was simulated numerically for the subsonic flow through a highly loaded low-pressure turbine. The configuration approximated cascade experiments that were conducted to investigate a reduction in turbine stage blade count, which can decrease both weight and mechanical complexity. At a nominal Reynolds number of 25,000 based upon axial chord and inlet conditions, massive separation occurred on the suction surface of each blade due to uncovered turning. Vortex generating jets were then used to help mitigate separation, thereby reducing wake losses. Computations were performed using both steady blowing and pulsed mass injection to study the effects of active flow control on the transitional flow occurring in the aft-blade and near-wake regions. The numerical method utilized a centered compact finite-difference scheme to represent spatial derivatives, that was used in conjunction with a low-pass Pade-type nondispersive filter operator to maintain stability. An implicit approximately factored time-marching algorithm was employed, and Newton-like subiterations were applied to achieve second-order temporal accuracy. Calculations were carried out on a massively parallel computing platform, using domain decomposition to distribute subzones on individual processors. A high-order overset grid approach preserved spatial accuracy in locally refined embedded regions. Features of the flowfields are described, and simulations are compared with each other, with available experimental data, and with a previously obtained baseline case for the noncontrolled flow. It was found that active flow control was able to maintain attached flow over an additional distance of 19–21% of the blade chord, relative to the baseline case, which resulted in a reduction of the wake total pressure loss coefficient of 53–56%.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

Sign in / Sign up

Export Citation Format

Share Document