Turbine Blade Internal Cooling Passages with Rib Turbulators

2006 ◽  
Vol 22 (2) ◽  
pp. 226-248 ◽  
Author(s):  
Je-Chin Han ◽  
Hamn-Ching Chen
Keyword(s):  
Turbine Blade ◽  
Internal Cooling ◽  
Rib Turbulators

Conjugate Heat Transfer Analysis of Internally Cooled Turbine Blade

2012 ◽  
Author(s):  
Ilhan Gorgulu ◽  
Baris Gumusel ◽  
I. Sinan Akmandor
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Turbulence Model ◽  
Conjugate Heat Transfer ◽  
Turbulence Models ◽  
Heat Transfer Analysis ◽  
Internal Cooling ◽  
Turbine Blade Cooling ◽  
Internally Cooled ◽  
Rib Turbulators

There are different characters of air flow in a conventional gas turbine blade cooling channel. These flow characters; including high streamline curvature caused from 180 degree bends, sequential flow separations caused from rib turbulators and pin-fin structures are analyzed separately with available commercial software for different turbulence models and validated against reliable experimental data from open literature. Also coupled conjugate heat transfer analyses on NASA C3X vane, which has only radial holes through blade span for cooling, are conducted with the same turbulence models. The accuracy information gathered from all these analyses; each interested with a single character of air and coupled conjugate heat transfer are put together and applied to a conjugate numerical analysis of internally cooled (VKI) LS-89 turbine blade. Internal cooling scheme which is applied to (VKI) LS-89 turbine blade encompassed the aforementioned flow characters and analyses are performed under realistic conditions. Because of the high temperature values occurring at realistic conditions, thermal conductivity and specific heat capacity of air and metal (Inconel 718) are modeled as temperature dependent material properties instead of using constant values. Conducted research revealed that 4 eqn. V2-f turbulence model gives similar results compared to the 2 eqn. Realizable k-e, k-w SST turbulence models for 180 degree bend and rib turbulator cases. However, at NASA C3X vane analyses V2-f turbulence model results are far more accurate than other two turbulence models in the manner of heat transfer coefficient and surface temperature distribution.

Review of Gas Turbine Internal Cooling Improvement Technology

2020 ◽  
Vol 143 (8) ◽  
Author(s):  
Farah Nazifa Nourin ◽  
Ryoichi S. Amano
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Cooling System ◽  
Guide Vane ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Internal Cooling ◽  
Gas Turbine Blade ◽  
Pin Fins ◽  
Rib Turbulators

Abstract The higher firing temperature reflects the higher efficiency of the gas turbine. However, using higher temperatures is limited as it may cause a rupture, bending, or failure of the turbine blades. Hence, the development of an effective internal cooling system of the gas turbine blade is essential. At the same time, it is necessary to ensure the lowest possible penalty on the thermodynamics performance cycle. Researchers are working over the years to find out the efficient cooling channel design with high transfer while the lowest pressure drop. They ran several cases both numerically and experimentally. This paper reviews the published research in the various methods of gas turbine internal cooling, such as using rib turbulators, dimples, jet impingement, pin fins, and guide vane, of the gas turbine blade.

Heat Transfer Enhancement by Criss-Cross Pattern Formed by 45° Angled Rib Turbulators in a Straight Square Duct

2017 ◽  
Author(s):  
Prashant Singh ◽  
Yongbin Ji ◽  
Mingyang Zhang ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Turbine Blade ◽  
Hydraulic Performance ◽  
Secondary Flows ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Conduction Model ◽  
Square Duct ◽  
Rib Turbulators

The need for higher turbine efficiency has been constantly pushing the turbine inlet temperatures to elevated levels. Hot gas path temperatures are much higher than the typical blade material yield temperature. Efficient internal cooling technologies are required for safe operation of gas turbine. Several internal cooling technologies have been developed in order to enhance the heat transfer from relatively hotter walls of turbine blade. For mid-chord region of turbine blade, rib turbulators are typically installed in multi-pass channels. Rib turbulators trip the boundary layer, induce secondary flows which enhance near wall shear as well as enhance turbulent mixing when they interact with surrounding walls. Research has been carried out on several aspects of rib turbulated passages in order to achieve higher thermal hydraulic performance. Generally, rib turbulators are installed on two opposite walls of serpentine passages in order to enhance heat transfer from both pressure and suction sides of blade through coolant flowing through complicated paths. Typical arrangement of rib turbulators were parallel to each other or having some offset from each other. In the present study, an attempt has been made to arrange 45° angled ribs in a way that they form a Criss-Cross pattern. Two ribbed configurations with Criss-Cross pattern - Inline and staggered, have been studied where the baseline case was smooth duct with no rib turbulators. The effective rib-pitch-to-rib-height ratio (p/e) was 8.6 and rib-height-to-channel-hydraulic diameter ratio (e/dh) was 0.1. The channel had a total length of 20 hydraulic diameters and the rib turbulators were installed at a distance of six hydraulic diameters from the inlet of the test section to allow flow development. Detailed heat transfer coefficients were measured using transient liquid crystal thermography employing 1D semi-infinite conduction model. Globally averaged Nusselt numbers are calculated from the detailed measurements and thermal hydraulic performance of configurations have been reported with respect to Reynolds number. The aim of this study was to develop a cooling configuration which has higher thermal-hydraulic performance compared to other traditional rib configurations. It has been found that the heat transfer characteristics of the inline and staggered configurations were similar to each other and ranged between three times D-B correlation to 2.7 times, for Reynolds number ranging from 30000 to 60000. Inline configuration had relatively lower frictional losses, however the thermal hydraulic performances of both the configurations were similar.

Recent Studies in Turbine Blade Internal Cooling

2010 ◽  
Vol 41 (8) ◽  
pp. 803-828 ◽  
Author(s):  
Michael Huh ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Internal Cooling

Shape design of internal cooling passages within a turbine blade

2012 ◽  
Vol 44 (4) ◽  
pp. 449-466 ◽  
Author(s):  
Grzegorz Nowak ◽  
Iwona Nowak
Keyword(s):  
Turbine Blade ◽  
Shape Design ◽  
Internal Cooling

Heat Transfer and Flow Phenomena in a Swirl Chamber Simulating Turbine Blade Internal Cooling

1998 ◽  
Author(s):  
C. R. Hedlund ◽  
P. M. Ligrani ◽  
H.-K. Moon ◽  
B. Glezer
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Internal Cooling ◽  
Vortex Pairs ◽  
Nusselt Numbers ◽  
Swirl Chamber ◽  
Flow Phenomena ◽  
Energy Balances

Heat transfer and fluid mechanics results are given for a swirl chamber whose geometry models an internal passage used to cool the leading edge of a turbine blade. The Reynolds numbers investigated, based on inlet duct characteristics, include values which are the same as in the application (18000–19400). The ratio of absolute air temperature between the inlet and wall of the swirl chamber ranges from 0.62 to 0.86 for the heat transfer measurements. Spatial variations of surface Nusselt numbers along swirl chamber surfaces are measured using infrared thermography in conjunction with thermocouples, energy balances, digital image processing, and in situ calibration procedures. The structure and streamwise development of arrays of Görtler vortex pairs, which develop along concave surfaces, are apparent from flow visualizations. Overall swirl chamber structure is also described from time-averaged surveys of the circumferential component of velocity, total pressure, static pressure, and the circumferential component of vorticity. Important variations of surface Nusselt numbers and time-averaged flow characteristics are present due to arrays of Görtler vortex pairs, especially near each of the two inlets, where Nusselt numbers are highest. Nusselt numbers then decrease and become more spatially uniform along the interior surface of the chamber as the flows advect away from each inlet.

Experimental Study on Flow Behavior and Heat Transfer Enhancement with Distinct Dimpled Gas Turbine Blade Internal Cooling Channel

2021 ◽  
pp. 1-28
Author(s):  
Farah Nazifa Nourin ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Thermal Performance ◽  
Diameter Ratio ◽  
Internal Cooling ◽  
Cooling Channel ◽  
Transfer Enhancement

Abstract The study presents the investigation on heat transfer distribution along a gas turbine blade internal cooling channel. Six different cases were considered in this study, using the smooth surface channel as a baseline. Three different dimples depth-to-diameter ratios with 0.1, 0.25, and 0.50 were considered. Different combinations of partial spherical and leaf dimples were also studied with the Reynolds numbers of 6,000, 20,000, 30,000, 40,000, and 50,000. In addition to the experimental investigation, the numerical study was conducted using Large Eddy Simulation (LES) to validate the data. It was found that the highest depth-to-diameter ratio showed the highest heat transfer rate. However, there is a penalty for increased pressure drop. The highest pressure drop affects the overall thermal performance of the cooling channel. The results showed that the leaf dimpled surface is the best cooling channel based on the highest Reynolds number's heat transfer enhancement and friction factor. However, at the lowest Reynolds number, partial spherical dimples with a 0.25 depth to diameter ratio showed the highest thermal performance.

Conventional Rib Turbulators For SCO2 Turbine Internal Cooling - Report

2021 ◽  
Author(s):  
Matthew Searle ◽  
Douglas Straub ◽  
James Black
Keyword(s):  
Internal Cooling ◽  
Rib Turbulators

Heat Transfer Implications of Acoustic Resonances in HP Turbine Blade Internal Cooling Channels

2015 ◽  
Author(s):  
C. Selcan ◽  
B. Cukurel ◽  
J. Shashank
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Cooling System ◽  
Resonance Condition ◽  
Order Approximation ◽  
Acoustic Resonance ◽  
Mode Shapes ◽  
Internal Cooling ◽  
The Impact ◽  
Standing Sound

In an attempt to investigate the acoustic resonance effect of serpentine passages on internal convection heat transfer, the present work examines a typical high pressure turbine blade internal cooling system, based on the geometry of the NASA E3 engine. In order to identify the associated dominant acoustic characteristics, a numerical FEM simulation (two-step frequency domain analysis) is conducted to solve the Helmholtz equation with and without source terms. Mode shapes of the relevant identified eigenfrequencies (in the 0–20kHz range) are studied with respect to induced standing sound wave patterns and the local node/antinode distributions. It is observed that despite the complexity of engine geometries, as a first order approximation, the predominant resonance behavior can be modeled by a same-ended straight duct. Therefore, capturing the physics observed in a generic geometry, the heat transfer ramifications are experimentally investigated in a scaled wind tunnel facility at a representative resonance condition. Focusing on the straight cooling channel’s longitudinal eigenmode in the presence of an isolated rib element, the impact of standing sound waves on convective heat transfer and aerodynamic losses are demonstrated by liquid crystal thermometry, local static pressure and sound level measurements. The findings indicate a pronounced heat transfer influence in the rib wake separation region, without a higher pressure drop penalty. This highlights the potential of modulating the aero-thermal performance of the system via acoustic resonance mode excitations.

Sign in / Sign up

Export Citation Format

Share Document