scholarly journals Heat transfer characteristics for inclined twin-jet impingement

2012 ◽  
Author(s):  
M. Kito ◽  
T. Matsumoto ◽  
T. Shakouchi ◽  
K. Tsujimoto ◽  
T. Ando
Keyword(s):  
Heat Transfer ◽  
Jet Impingement ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Heat Transfer Characteristics of Downward Facing Hot Horizontal Surfaces Using Mist Jet Impingement

2017 ◽  
Author(s):  
Ashutosh Kumar Yadav ◽  
Parantak Sharma ◽  
Avadhesh Kumar Sharma ◽  
Mayank Modak ◽  
Vishal Nirgude ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Cooling System ◽  
Water Pressure ◽  
Jet Impingement ◽  
Surface Heat ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Impinging jet cooling technique has been widely used extensively in various industrial processes, namely, cooling and drying of films and papers, processing of metals and glasses, cooling of gas turbine blades and most recently cooling of various components of electronic devices. Due to high heat removal rate the jet impingement cooling of the hot surfaces is being used in nuclear industries. During the loss of coolant accidents (LOCA) in nuclear power plant, an emergency core cooling system (ECCS) cool the cluster of clad tubes using consisting of fuel rods. Controlled cooling, as an important procedure of thermal-mechanical control processing technology, is helpful to improve the microstructure and mechanical properties of steel. In industries for heat transfer efficiency and homogeneous cooling performance which usually requires a jet impingement with improved heat transfer capacity and controllability. It provides better cooling in comparison to air. Rapid quenching by water jet, sometimes, may lead to formation of cracks and poor ductility to the quenched surface. Spray and mist jet impingement offers an alternative method to uncontrolled rapid cooling, particularly in steel and electronics industries. Mist jet impingement cooling of downward facing hot surface has not been extensively studied in the literature. The present experimental study analyzes the heat transfer characteristics a 0.15mm thick hot horizontal stainless steel (SS-304) foil using Internal mixing full cone (spray angle 20 deg) mist nozzle from the bottom side. Experiments have been performed for the varied range of water pressure (0.7–4.0 bar) and air pressure (0.4–5.8 bar). The effect of water and air inlet pressures, on the surface heat flux has been examined in this study. The maximum surface heat flux is achieved at stagnation point and is not affected by the change in nozzle to plate distance, Air and Water flow rates.

Numerical Simulation Study of Impinging Jet Impact Fin Surface on Heat Transfer Characteristics

2013 ◽  
Vol 663 ◽  
pp. 586-591 ◽  
Author(s):  
Li Ming Zhou ◽  
Lei Zhu ◽  
Jing Quan Zhao ◽  
Meng Zheng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Thermal Resistance ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Transfer Characteristics ◽  
Jet Impact ◽  
Jet Array

Three-dimensional numerical simulation was implemented to analyze the heat transfer characteristics for jet impingement impact fin surface. 60 calculation cases were simulated to investigate the effects of different fin surfaces on heat transfer characteristics, and 12 jet array impingement cases were calculated for comparison. The results shown that the fin shape, the height and the fin arrangement were the critical factors to affect the jet impingement and the best combination were existed in a certain range. The thermal resistance of cylinder fin arranged in order was34.7 percent higher than that of cylinder fin arranged staggered. The thermal resistance of square fin arranged in order was38.9 percent higher than that of square fin arranged staggered .The heat transfer coefficients of impinging jet impact fin surface were better than that of jet array impingement. The fitting correlations on heat transfer of impinging jet impact fin surface were given.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement Cooling

2011 ◽  
Vol 148-149 ◽  
pp. 680-683
Author(s):  
Run Peng Sun ◽  
Wei Bing Zhu ◽  
Hong Chen ◽  
Chang Jiang Chen
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Cross Flow ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Transfer Characteristic ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Three-dimensional numerical study is conducted to investigate the heat transfer characteristics for the flow impingement cooling in the narrow passage based on cooling technology of turbine blade.The effects of the jet Reynolds number, impingement distance and initial cross-flow on heat transfer characteristic are investigated.Results show that when other parameters remain unchanged local heat transfer coefficient increases with increase of jet Reynolds number；overall heat transfer effect is reduced by initial cross-flow；there is an optimal distance to the best effect of heat transfer.

Sign in / Sign up

Export Citation Format

Share Document