scholarly journals Tool wear of sintered cubic boron nitride compact in cutting hardened steel with high-pressure coolant supplied

2016 ◽  
Author(s):  
T. Wada ◽  
K. Okayama ◽  
Y. Morigo
Keyword(s):  
High Pressure ◽  
Boron Nitride ◽  
Tool Wear ◽  
Cubic Boron Nitride ◽  
Hardened Steel ◽  
High Pressure Coolant

Tool Wear of Polycrystalline Cubic Boron Nitride Compact Tools in Cutting Hardened Steel

2012 ◽  
Vol 488-489 ◽  
pp. 724-728 ◽  
Author(s):  
Tadahiro Wada
Keyword(s):  
Particle Size ◽  
Boron Nitride ◽  
Tool Wear ◽  
Tool Life ◽  
Cubic Boron Nitride ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Polycrystalline Cubic Boron Nitride ◽  
Cbn Tool ◽  
High Cutting Speed

Using polycrystalline cubic boron nitride compact (cBN) tools, which have different cBN contents and cBN particle sizes, the influences of both the cBN content and the cBN particle size on tool wear in turning of hardened steel at various cutting speeds was experimentally investigated. Three types of cBN tools (a cBN content of 45-55% and 75%, and a cBN particle size of 0.5 μm and 5 μm, respectively) were tested. Furthermore, three kinds of chamfered and honed cutting edges were also used. The main results obtained are as follows: (1) In the case of the cBN tools with the same cBN particle size of 5.0 μm, the tool life of the cBN tool with a cBN content of 75% was longer than that of the cBN tool with a cBN content of 45% at low cutting speed. However, at high cutting speed, the tool life of the cBN tool with a cBN content of 75% was shorter. (2) The tool life of the cBN tool with both a cBN content of 55% and a cBN particle size of 0.5 μm was the longest. (3) The tool wear of cBN tools decreased with a decrease in chamfer width.

Effect of Al on the Formation of Cubic Boron Nitride Using Ni3Al Solvent under High Pressure

2007 ◽  
Vol 46 (11) ◽  
pp. 7388-7391 ◽  
Author(s):  
Yoichi Kubota ◽  
Kosuke Kosuda ◽  
Takashi Taniguchi
Keyword(s):  
High Pressure ◽  
Boron Nitride ◽  
Cubic Boron Nitride

scholarly journals Experimental Study of tool Wear Mechanisms in Conventional and High Pressure Coolant Assisted Machining of Titanium Alloy Ti17

2013 ◽  
Vol 554-557 ◽  
pp. 1961-1966 ◽  
Author(s):  
Yessine Ayed ◽  
Guenael Germain ◽  
Amine Ammar ◽  
Benoit Furet
Keyword(s):  
High Pressure ◽  
Titanium Alloy ◽  
Tool Wear ◽  
Titanium Alloys ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Cutting Forces ◽  
Cutting Edge ◽  
Rake Face ◽  
High Pressure Coolant

Titanium alloys are known for their excellent mechanical properties, especially at high temperature. But this specificity of titanium alloys can cause high cutting forces as well as a significant release of heat that may entail a rapid wear of the cutting tool. To cope with these problems, research has been taken in several directions. One of these is the development of assistances for machining. In this study, we investigate the high pressure coolant assisted machining of titanium alloy Ti17. High pressure coolant consists of projecting a jet of water between the rake face of the tool and the chip. The efficiency of the process depends on the choice of the operating parameters of machining and the parameters of the water jet such as its pressure and its diameter. The use of this type of assistance improves chip breaking and increases tool life. Indeed, the machining of titanium alloys is generally accompanied by rapid wear of cutting tools, especially in rough machining. The work done focuses on the wear of uncoated tungsten carbide tools during machining of Ti17. Rough and finish machining in conventional and in high pressure coolant assistance conditions were tested. Different techniques were used in order to explain the mechanisms of wear. These tests are accompanied by measurement of cutting forces, surface roughness and tool wear. The Energy-dispersive X-ray spectroscopy (EDS) analysis technique made it possible to draw the distribution maps of alloying elements on the tool rake face. An area of material deposition on the rake face, characterized by a high concentration of titanium, was noticed. The width of this area and the concentration of titanium decreases in proportion with the increasing pressure of the coolant. The study showed that the wear mechanisms with and without high pressure coolant assistance are different. In fact, in the condition of conventional machining, temperature in the cutting zone becomes very high and, with lack of lubrication, the cutting edge deforms plastically and eventually collapses quickly. By contrast, in high pressure coolant assisted machining, this problem disappears and flank wear (VB) is stabilized at high pressure. The sudden rupture of the cutting edge observed under these conditions is due to the propagation of a notch and to the crater wear that appears at high pressure. Moreover, in rough condition, high pressure assistance made it possible to increase tool life by up to 400%.

Ultraviolet light emission from self-organized p–n domains in cubic boron nitride bulk single crystals grown under high pressure

2002 ◽  
Vol 81 (22) ◽  
pp. 4145-4147 ◽  
Author(s):  
T. Taniguchi ◽  
K. Watanabe ◽  
S. Koizumi ◽  
I. Sakaguchi ◽  
T. Sekiguchi ◽  
...  
Keyword(s):  
High Pressure ◽  
Boron Nitride ◽  
Single Crystals ◽  
Ultraviolet Light ◽  
Light Emission ◽  
Cubic Boron Nitride ◽  
Self Organized ◽  
Bulk Single Crystals
Sign in / Sign up

Export Citation Format

Share Document