scholarly journals On the application of magnetoelastic properties measurements for plastic level determination in martensitic steels

2018 ◽  
Vol 69 (6) ◽  
pp. 502-506 ◽  
Author(s):  
Leszek Piotrowski ◽  
Marek Chmielewski ◽  
Zbigniew Kowalewski
Keyword(s):  
Plastic Deformation ◽  
Domain Walls ◽  
Martensitic Steel ◽  
Magnetic Domain ◽  
Martensitic Steels ◽  
Reliable Determination ◽  
Magnetoelastic Properties ◽  
Tension And Compression ◽  
Deformation Level ◽  
Non Destructive

Abstract The change in the dislocation density, induced by plastic deformation, influences strongly the magnetic domain structure inside the material. Being so, classic parameters, like the coercivity or magnetic permeability, can be a good measure of the deformation level, yet their reliable determination in a non-destructive way in industrial environment is problematic. The magnetoacoustic emission (MAE) which results from the non-180° domain walls (DW) movement in materials with non-zero magnetostriction can be used as an alternative. The intensity of the MAE signal changes strongly as a result of plastic deformation for both tensile and compressive deformation. It is however possible to discern those cases by analysing the changes in the shape of the MAE signal envelopes. The set of the martensitic steel samples (P91) deformed up to 10% (for both tension and compression) was investigated. Due to geometrical limitations imposed by the special mounting system, enabling compression without buckling, the sample had the shape resulting in low signal to noise (S/N) ratio. Being so the optimization of FFT filtering and wavelet analysis was performed in order to improve sensitivity of the proposed method of deformation level determination.

Non-Destructive Evaluation of Mechanical Properties of Magnetic Materials

1999 ◽  
Vol 591 ◽  
Author(s):  
Kevin P. Kankolenski ◽  
Susan Z. Hua ◽  
David X. Yang ◽  
G. E. Hicho ◽  
L. J. Swartzendruber ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Domain Walls ◽  
Tensile Axis ◽  
Hysteresis Loops ◽  
Strain Curve ◽  
Low Carbon ◽  
Barkhausen Effect ◽  
Non Destructive Evaluation ◽  
Non Destructive

ABSTRACTA magnetic-based non-destructive evaluation (NDE) method, which employs Barkhausen effect and measurement of the hysteresis loops, is used to correlate the magnetic and mechanical properties of ultra low carbon (ULC) steel. In particular, the NDE method was used to detect small deviations from linearity that occur in the stress-strain curve well below the 0.2% offset strain, and which generally defines the yield point in materials. Results show that three parameters: jumpsum and jumpsum rate (derived from the Barkhausen spectrum), and the relative permeability (derived from the B-H loops) varies sensitively with small permanent strains, and can be related to the plastic deformation in ULC steels. Investigation of micromagnetic structure revealed that plastic deformation leaves a residual stress state in the samples; the associated magneto-elastic energy makes the favorable easy axis of magnetization in a given grain to be the one that lies closest to the tensile axis. The consequence of this realignment of domains is that wall motion becomes intergranular in nature (as opposed to intragranular in unstrained samples). As a result, the more complex grain boundaries instead of dislocations, become the dominant pinning sites for domain walls. These observations provide a microscopic interpretation of the observed changes in the measured magnetic properties.

The direct determination of magnetic domain wall profiles using a split detector STEM

1978 ◽  
Vol 36 (1) ◽  
pp. 466-467
Author(s):  
J.N. Chapman ◽  
P.E. Batson ◽  
E.M. Waddell ◽  
R.P. Ferrier
Keyword(s):  
Electron Microscope ◽  
Domain Wall ◽  
Transmission Electron Microscope ◽  
Domain Walls ◽  
Photographic Plate ◽  
Magnetic Domain ◽  
Direct Determination ◽  
Quantitative Information ◽  
Scanning Transmission Electron Microscope ◽  
Transmission Electron

By far the most commonly used mode of Lorentz microscopy in the examination of ferromagnetic thin films is the Fresnel or defocus mode. Use of this mode in the conventional transmission electron microscope (CTEM) is straightforward and immediately reveals the existence of all domain walls present. However, if such quantitative information as the domain wall profile is required, the technique suffers from several disadvantages. These include the inability to directly observe fine image detail on the viewing screen because of the stringent illumination coherence requirements, the difficulty of accurately translating part of a photographic plate into quantitative electron intensity data, and, perhaps most severe, the difficulty of interpreting this data. One solution to the first-named problem is to use a CTEM equipped with a field emission gun (FEG) (Inoue, Harada and Yamamoto 1977) whilst a second is to use the equivalent mode of image formation in a scanning transmission electron microscope (STEM) (Chapman, Batson, Waddell, Ferrier and Craven 1977), a technique which largely overcomes the second-named problem as well.

Lorentz microscopy study of magnetic domain walls in Fe-Cr-Co alloys

1978 ◽  
Vol 36 (1) ◽  
pp. 462-463
Author(s):  
Yalcin Belli
Keyword(s):  
Domain Walls ◽  
Magnetic Domain ◽  
Microscopy Study ◽  
Ferromagnetic Phase ◽  
Stable Phase ◽  
Magnetic Domains ◽  
Lorentz Microscopy ◽  
Magnetic Hardening ◽  
Electron Microscopes ◽  
Co Alloys

Fe-Cr-Co alloys have great technological potential to replace Alnico alloys as hard magnets. The relationship between the microstructures and the magnetic properties has been recently established for some of these alloys. The magnetic hardening has been attributed to the decomposition of the high temperature stable phase (α) into an elongated Fe-rich ferromagnetic phase (α1) and a weakly magnetic or non-magnetic Cr-rich phase (α2). The relationships between magnetic domains and domain walls and these different phases are yet to be understood. The TEM has been used to ascertain the mechanism of magnetic hardening for the first time in these alloys. The present paper describes the magnetic domain structure and the magnetization reversal processes in some of these multiphase materials. Microstructures to change properties resulting from, (i) isothermal aging, (ii) thermomagnetic treatment (TMT) and (iii) TMT + stepaging have been chosen for this investigation. The Jem-7A and Philips EM-301 transmission electron microscopes operating at 100 kV have been used for the Lorentz microscopy study of the magnetic domains and their interactions with the finely dispersed precipitate phases.

Temperature Dependence of Magnetic Domains and Wall Structures

1972 ◽  
Vol 30 ◽  
pp. 496-497
Author(s):  
Sonoko Tsukahara ◽  
Tadami Taoka ◽  
Hisao Nishizawa
Keyword(s):  
Temperature Dependence ◽  
Domain Walls ◽  
Magnetic Domain ◽  
Iron Film ◽  
Objective Lens ◽  
Lorentz Microscopy ◽  
Domain Structures ◽  
Wall Structures ◽  
Crystal Films ◽  
Metallurgical Structure

The high voltage Lorentz microscopy was successfully used to observe changes with temperature; of domain structures and metallurgical structures in an iron film set on the hot stage combined with a goniometer. The microscope used was the JEM-1000 EM which was operated with the objective lens current cut off to eliminate the magnetic field in the specimen position. Single crystal films with an (001) plane were prepared by the epitaxial growth of evaporated iron on a cleaved (001) plane of a rocksalt substrate. They had a uniform thickness from 1000 to 7000 Å.The figure shows the temperature dependence of magnetic domain structure with its corresponding deflection pattern and metallurgical structure observed in a 4500 Å iron film. In general, with increase of temperature, the straight domain walls decrease in their width (at 400°C), curve in an iregular shape (600°C) and then vanish (790°C). The ripple structures with cross-tie walls are observed below the Curie temperature.

Highlights in the history of X-ray topography1

1995 ◽  
Vol 210 (6) ◽  
Author(s):  
A. R. Lang
Keyword(s):  
Magnetic Domain ◽  
Diffraction Theory ◽  
Dislocation Loops ◽  
X Ray Diffraction ◽  
X Ray ◽  
Domain Structures ◽  
Structure Factors ◽  
History Of ◽  
Dislocation Sources ◽  
Non Destructive

AbstractX-ray topography provides a non-destructive method of mapping point-by-point variations in orientation and reflecting power within crystals. The discovery, made by several workers independently, that in nearly perfect crystals it was possible to detect individual dislocations by X-ray diffraction contrast started an epoch of rapid exploitation of X-ray topography as a new, general method for assessing crystal perfection. Another discovery, that of X-ray Pendellösung, led to important theoretical developments in X-ray diffraction theory and to a new and precise method for measuring structure factors on an absolute scale. Other highlights picked out for mention are studies of Frank-Read dislocation sources, the discovery of long dislocation helices and lines of coaxial dislocation loops in aluminium, of internal magnetic domain structures in Fe-3 wt.% Si, and of stacking faults in silicon and natural diamonds.

scholarly journals Phase shifter based on voltage-controlled magnetic domain walls

AIP Advances ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 075225
Author(s):  
Xiao Zhang ◽  
Chen Zhang ◽  
Chonglei Sun ◽  
Xiao Xu ◽  
Liuge Du ◽  
...  
Keyword(s):  
Phase Shifter ◽  
Domain Walls ◽  
Magnetic Domain ◽  
Magnetic Domain Walls
Sign in / Sign up

Export Citation Format

Share Document