scholarly journals Flexural Property in Out-of-Plane Bending Test of Cross Laminated Timber(CLT) Composed of Different Grade Lamina of Sugi.

2021 ◽  
Vol 70 (7) ◽  
pp. 561-566
Author(s):  
Ken YAMAMOTO ◽  
Kazuhiko FUJITA ◽  
Yasutaka WATANABE ◽  
Atsushi MIYATAKE ◽  
Tatsuya SHIBUSAWA ◽  
...  
Keyword(s):  
Bending Test ◽  
Flexural Property ◽  
Cross Laminated Timber ◽  
Out Of Plane ◽  
Plane Bending

scholarly journals Modeling of Cross-Laminated Timber (CLT) panels loaded with combined out-of-plane bending and compression

2022 ◽  
Vol 250 ◽  
pp. 113335
Author(s):  
Zirui Huang ◽  
Dongsheng Huang ◽  
Ying-Hei Chui ◽  
Yurong Shen ◽  
Hossein Daneshvar ◽  
...  
Keyword(s):  
Cross Laminated Timber ◽  
Out Of Plane ◽  
Plane Bending

Comparison of Failure Modes of Piping Systems With Wall Thinning Subjected to In-Plane, Out-of-Plane, and Mixed Mode Bending Under Seismic Load: An Experimental Approach

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Izumi Nakamura ◽  
Akihito Otani ◽  
Masaki Shiratori
Keyword(s):  
Dynamic Behavior ◽  
Failure Modes ◽  
Seismic Load ◽  
Piping System ◽  
Shake Table ◽  
Shake Table Tests ◽  
Wall Thinning ◽  
Piping Systems ◽  
Out Of Plane ◽  
Plane Bending

Pressurized piping systems used for an extended period may develop degradations such as wall thinning or cracks due to aging. It is important to estimate the effects of degradation on the dynamic behavior and to ascertain the failure modes and remaining strength of the piping systems with degradation through experiments and analyses to ensure the seismic safety of degraded piping systems under destructive seismic events. In order to investigate the influence of degradation on the dynamic behavior and failure modes of piping systems with local wall thinning, shake table tests using 3D piping system models were conducted. About 50% full circumferential wall thinning at elbows was considered in the test. Three types of models were used in the shake table tests. The difference of the models was the applied bending direction to the thinned-wall elbow. The bending direction considered in the tests was either of the in-plane bending, out-of-plane bending, or mixed bending of the in-plane and out-of-plane. These models were excited under the same input acceleration until failure occurred. Through these tests, the vibration characteristic and failure modes of the piping models with wall thinning under seismic load were obtained. The test results showed that the out-of-plane bending is not significant for a sound elbow, but should be considered for a thinned-wall elbow, because the life of the piping models with wall thinning subjected to out-of-plane bending may reduce significantly.

Out-of-plane tensile modulus of CFRP laminates by 3-point bending test

2014 ◽  
Vol 24 (3) ◽  
pp. 221-237 ◽  
Author(s):  
Eiichi Hara ◽  
Tomohiro Yokozeki ◽  
Hiroshi Hatta ◽  
Yutaka Iwahori ◽  
Takashi Ishikawa
Keyword(s):  
Tensile Modulus ◽  
Bending Test ◽  
Cfrp Laminates ◽  
Out Of Plane

Stresses in Curved, Circular Thin-Wall Tubes

1963 ◽  
Vol 30 (1) ◽  
pp. 134-135
Author(s):  
E. A. Utecht
Keyword(s):  
Thin Wall ◽  
Bending Moments ◽  
Circular Tubes ◽  
Out Of Plane ◽  
Thin Walled ◽  
Plane Bending

Curves are presented which give stress intensification factors for curved, thin-walled circular tubes under various combinations of in-plane and out-of-plane bending moments.

Out-of-Plane Bending (Opb) Test of Large Diameter Mooring Chains

2021 ◽  
Author(s):  
m.r. Karimi ◽  
J. Braun ◽  
E. Gooijer ◽  
P. Barros ◽  
E. Carlberg ◽  
...  
Keyword(s):  
Large Diameter ◽  
Out Of Plane ◽  
Plane Bending
Sign in / Sign up

Export Citation Format

Share Document