scholarly journals The Influence of Curing Temperature on Hydrated Products of Blast Furnace Slag Cement and Its Porosity at the Early Stage of Hydration

2009 ◽  
Vol 58 (8) ◽  
pp. 715-720 ◽  
Author(s):  
Tsuyoshi SAITO ◽  
Takahisa UCHIDA ◽  
Yun Sub LEE ◽  
Nobuaki OTSUKI
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Early Stage ◽  
Curing Temperature ◽  
Slag Cement ◽  
Hydrated Products ◽  
Furnace Slag

scholarly journals Application of the High Early Strength Type Expansive Agent to the Blast Furnace Slag Combination Concrete with GGBFS under Steam Curing

2019 ◽  
Vol 278 ◽  
pp. 01005
Author(s):  
Erica Enzaki ◽  
Takashi Sakuma ◽  
Eizou Takeshita ◽  
Shigeyuki Date
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Early Stage ◽  
Precast Concrete ◽  
Curing Temperature ◽  
Strength Development ◽  
Steam Curing ◽  
Expansive Agent ◽  
Early Strength ◽  
Furnace Slag

In recent years, the use of blast furnace slag material is being focused as environmental loading reduction and sustainable construction. However, in general, autogeneours shrinkage of the concrete using much amount of GGBFS is large in compared to normal concrete, therefore risk of cracking should be cared. On the other hand, strength development speed of concrete at early stage will be decreasing as the dosage of GGBFS increases, even under steam curing condition. It can be considered these points will be significant disadvantage in both productivity and quality of precast concrete. So in this study, early strength type expansive agent and setting accelerator were used in combination. As a result, it was confirmed that compressive strength at early stage is obviously increased. And steam curing temperature can be reduced about 10 degrees, and also, 600×10-6 of restraint expansion was obtained.

ON THE USE OF SLAG CEMENT COMPOSITIONS IN THE CONSTRUCTION OF WELLS

2017 ◽  
pp. 80-85
Author(s):  
V. P. Ovchinnikov ◽  
O. V. Rozhkova ◽  
N. A. Aksenova ◽  
P. V. Ovchinnikov
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Elevated Temperatures ◽  
Cement Mortar ◽  
Setting Time ◽  
Rheological Parameters ◽  
Slag Cement ◽  
Furnace Slag

In the article studies of oil-filled compositions with the addition of blast-furnace slag for strength at elevated temperatures are presented. The rheological parameters of the slag cement slag cement mortar, as well as the setting time, were studied. Conclusions are drawn about the prospects of further study of slag cementcontaining compositions.

scholarly journals Phase Transformation of Kaolin-Ground Granulated Blast Furnace Slag from Geopolymerization to Sintering Process

2021 ◽  
Vol 7 (3) ◽  
pp. 32
Author(s):  
Noorina Hidayu Jamil ◽  
Mohd. Mustafa Al Bakri Abdullah ◽  
Faizul Che Pa ◽  
Mohamad Hasmaliza ◽  
Wan Mohd Arif W. Ibrahim ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Room Temperature ◽  
Curing Temperature ◽  
Curing Process ◽  
Sintering Process ◽  
Granulated Blast Furnace Slag ◽  
Fluxing Agent ◽  
Furnace Slag

The main objective of this research was to investigate the influence of curing temperature on the phase transformation, mechanical properties, and microstructure of the as-cured and sintered kaolin-ground granulated blast furnace slag (GGBS) geopolymer. The curing temperature was varied, giving four different conditions; namely: Room temperature, 40, 60, and 80 °C. The kaolin-GGBS geopolymer was prepared, with a mixture of NaOH (8 M) and sodium silicate. The samples were cured for 14 days and sintered afterwards using the same sintering profile for all of the samples. The sintered kaolin-GGBS geopolymer that underwent the curing process at the temperature of 60 °C featured the highest strength value: 8.90 MPa, and a densified microstructure, compared with the other samples. The contribution of the Na2O in the geopolymerization process was as a self-fluxing agent for the production of the geopolymer ceramic at low temperatures.

Reactivity and performance of dry granulation blast furnace slag cement

2019 ◽  
Vol 95 ◽  
pp. 19-24 ◽  
Author(s):  
Junxiang Liu ◽  
Qingbo Yu ◽  
Zongliang Zuo ◽  
Fan Yang ◽  
Zhicheng Han ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Slag Cement ◽  
Dry Granulation ◽  
And Performance ◽  
Furnace Slag

scholarly journals STUDY ON 1DAY PAVE MIXING HIGH STRENGTH PORTLAND CEMENT AND BLAST FURNACE SLAG CEMENT TYPE B

2017 ◽  
Vol 71 (1) ◽  
pp. 308-314
Author(s):  
Shingo YOSHIMOTO ◽  
Tatsuo SHINMI ◽  
Hiroyoshi KATO ◽  
Takatoshi MOTOORI
Keyword(s):  
Blast Furnace ◽  
Portland Cement ◽  
Blast Furnace Slag ◽  
High Strength ◽  
Type B ◽  
Cement Type ◽  
Slag Cement ◽  
Furnace Slag

scholarly journals PROPERTIES OF CONCRETE USING BLAST-FURNACE SLAG CEMENT TYPE A WITH MODIFIED CHEMICAL COMPOSITION

2010 ◽  
Vol 64 (1) ◽  
pp. 244-250 ◽  
Author(s):  
Shingo MIYAZAWA ◽  
Takashi YOKOMURO ◽  
Hiromi FUJIWARA ◽  
Kiyoshi KOIBUCHI
Keyword(s):  
Blast Furnace ◽  
Chemical Composition ◽  
Blast Furnace Slag ◽  
Type A ◽  
Cement Type ◽  
Slag Cement ◽  
Furnace Slag
Sign in / Sign up

Export Citation Format

Share Document