scholarly journals Variable Amplitude Loading Test of Transverse Stiffener Joints for Fatigue Design of Steel Highway Bridges.

1995 ◽  
Vol 44 (500) ◽  
pp. 557-561
Author(s):  
Masahiro SAKANO ◽  
Ichizo MIKAMI ◽  
Ken'ichi KANO ◽  
Eiichi YONEMOTO
Keyword(s):  
Highway Bridges ◽  
Loading Test ◽  
Variable Amplitude Loading ◽  
Variable Amplitude ◽  
Fatigue Design ◽  
Steel Highway Bridges

scholarly journals Experimental Assessment on the Flexural Bonding Performance of Concrete Beam with GFRP Reinforcing Bar under Repeated Loading

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Minkwan Ju ◽  
Hongseob Oh
Keyword(s):  
Bond Length ◽  
Repeated Loading ◽  
Variable Loading ◽  
Loading Test ◽  
Variable Amplitude Loading ◽  
Static Test ◽  
Variable Amplitude ◽  
Reinforcing Bar ◽  
Bond Performance ◽  
Bonding Performance

This study intends to investigate the flexural bond performance of glass fiber-reinforced polymer (GFRP) reinforcing bar under repeated loading. The flexural bond tests reinforced with GFRP reinforcing bars were carried out according to the BS EN 12269-1 (2000) specification. The bond test consisted of three loading schemes: static, monotonic, and variable-amplitude loading to simulate ambient loading conditions. The empirical bond length based on the static test was 225 mm, whereas it was 317 mm according to ACI 440 1R-03. Each bond stress on the rib is released and bonding force is enhanced as the bond length is increased. Appropriate level of bond length may be recommended with this energy-based analysis. For the monotonic loading test, the bond strengths at pullout failure after 2,000,000 cycles were 10.4 MPa and 6.5 MPa, respectively: 63–70% of the values from the static loading test. The variable loading test indicated that the linear cumulative damage theory on GFRP bonding may not be appropriate for estimating the fatigue limit when subjected to variable-amplitude loading.

Fatigue Testing of Full Scale Girth Welded Pipes Under Variable Amplitude Loading

2012 ◽  
Author(s):  
Y.-H. Zhang ◽  
S. J. Maddox
Keyword(s):  
Fatigue Limit ◽  
Fatigue Damage ◽  
Fatigue Testing ◽  
Full Scale ◽  
Variable Amplitude Loading ◽  
Variable Amplitude ◽  
Fatigue Design ◽  
Miner’S Rule ◽  
Miner's Rule ◽  
Loading Spectrum

In the fatigue design of steel catenary risers there are concerns regarding the fatigue damage to girth welds from low stresses, below the constant amplitude fatigue limit, in the loading spectrum and the validity of Miner’s cumulative damage rule. In both cases there is increasing evidence that current design methods can be non-conservative. These fundamental issues were addressed in a recent JIP. A key feature was development of the resonance fatigue testing rigs to enable them to test full-scale pipes under variable amplitude loading. Such tests were performed under a loading spectrum representative of that experienced by some risers, with many tests lasting over 100 million cycles to investigate the fatigue damage due to small stresses as well as the validity of Miner’s rule. However, the resonance rigs are only capable of producing spectrum loading by gradually increasing or decreasing the applied load, whereas more ‘spiky’ random load sequences may be relevant in practice. Therefore the programme also included fatigue tests in conventional testing machines on strip specimens cut from pipes to compare the two types of loading sequence. This paper presents the results of these tests, conclusions drawn and recommendations for changes to current fatigue design guidance for girth welded pipes regarding the definition of the fatigue limit, allowance for the damaging effect of low stresses and the validity of Miner’s rule.

Fatigue Testing of Full Scale Girth Welded Pipes Under Variable Amplitude Loading

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Y.-H. Zhang ◽  
S. J. Maddox
Keyword(s):  
Fatigue Limit ◽  
Fatigue Damage ◽  
Fatigue Testing ◽  
Full Scale ◽  
Variable Amplitude Loading ◽  
Variable Amplitude ◽  
Fatigue Design ◽  
Miner’S Rule ◽  
Miner's Rule ◽  
Loading Spectrum

In the fatigue design of steel catenary risers, there are concerns regarding the fatigue damage to girth welds from low stresses, below the constant amplitude fatigue limit, in the loading spectrum and the validity of Miner's cumulative damage rule. These fundamental issues were addressed in a recent joint-industrial project (JIP). A key feature was development of the resonance fatigue testing rigs to enable them to test full-scale pipes under variable amplitude loading. Such tests were performed under a loading spectrum representative of that experienced by some risers, with many tests lasting over 100 million cycles to investigate the fatigue damage due to small stresses as well as the validity of Miner's rule. However, the resonance rigs are only capable of producing spectrum loading by gradually increasing or decreasing the applied load whereas more “spiky” random load sequences may be relevant in practice. Therefore, the program also included fatigue tests in conventional testing machines on strip specimens cut from pipes to compare the two types of loading sequence. This paper presents the results of these tests, conclusions drawn, and recommendations for changes to current fatigue design guidance for girth welded pipes regarding the definition of the fatigue limit, allowance for the damaging effect of low stresses, and the validity of Miner's rule.

Sign in / Sign up

Export Citation Format

Share Document