scholarly journals Stress corrosion cracking in Cu alloys, VII. Stress corrosion cracking of Cu-9 at%Al alloy single crystals.

1985 ◽  
Vol 34 (386) ◽  
pp. 1321-1326 ◽  
Author(s):  
Takuro MIMAKI ◽  
Satoshi HASHIMOTO ◽  
Sei MIURA
Keyword(s):  
Stress Corrosion ◽  
Single Crystals ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy ◽  
Cu Alloys

scholarly journals Stress corrosion cracking in Cu alloys, VIII. Stress corrosion cracking of Cu-9 at%Al alloy bicrystals.

1985 ◽  
Vol 34 (386) ◽  
pp. 1327-1332 ◽  
Author(s):  
Takuro MIMAKI ◽  
Hiroshi FUKUNAGA ◽  
Satoshi HASHIMOTO ◽  
Sei MIURA
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy ◽  
Cu Alloys

Role of Stress in the Stress Corrosion Cracking of a Mg-Al Alloy

CORROSION ◽  
1973 ◽  
Vol 29 (6) ◽  
pp. 251-260 ◽  
Author(s):  
W. R. WEARMOUTH ◽  
G. P DEAN ◽  
R. N. PARKINS
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy

Influence of Malonic Acid on the Corrosion and SCC Behaviour of Anodic Coated 1050 Al-Alloys

2010 ◽  
Vol 438 ◽  
pp. 155-162 ◽  
Author(s):  
Panayotis Spathis ◽  
Efthimios Papastergiadis ◽  
Georgios Stalidis ◽  
Georgios Papanastasiou
Keyword(s):  
Stress Corrosion ◽  
Acid Concentration ◽  
Malonic Acid ◽  
Stress Level ◽  
Current Density ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy ◽  
Applied Potential ◽  
Protective Properties

Aim of the present work is the study of corrosion and stress corrosion cracking behaviour of 1050 Al-Alloy anodised in a 3M H2SO4 anodising bath with the presence in it of malonic acid, in various concentrations and anodising current densities. The investigation was carried out by SCC (Stress Corrosion Cracking) tests and electrochemical measurements. The influence of applied potential on SCC behaviour was also examined. The corrosion and SCC behaviour of anodised 1050 Al-Alloy was found to vary with malonic acid concentration, anodising conditions, applied potential and stress level. In SCC conditions all prepared coatings protected the bare alloy, with better protective properties in the case of 0.015M concentration of malonic acid prepared with a 6 A.dm-2 anodising current density. The coating prepared in these conditions had better mechanical properties as indicated from the increased protection at a high stress level and also the better behaviour in corrosion, without stress, conditions of coatings prepared in different conditions of malonic acid concentration and anodising current density. For the interpretation of the results, properties of the anodic coatings as thickness, packing density, coating ratio, roughness, were also studied. The anodic coating formed in a electrolytic bath of 0.015M concentration of malonic acid and a 6 A.dm-2 anodising current density was found to be less porous, more compact and rough, with better oxide structure. Prepared coatings were found to increase protective properties in an area of applied potentials slightly more anodic than the free corrosion potential values.

scholarly journals Effect of pH on Stress Corrosion Cracking of 6082 Al Alloy

Metals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 578 ◽  
Author(s):  
C. Panagopoulos ◽  
Emmanuel Georgiou ◽  
K. Giannakopoulos ◽  
P. Orfanos
Keyword(s):  
Aluminum Alloy ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy ◽  
Cracking Behavior ◽  
Effect Of Ph ◽  
Cracking Mechanisms ◽  
6082 Aluminum Alloy ◽  
6082 Al Alloy

In this work, the effect of pH (3, 7 and 10) on the stress corrosion cracking behavior of 6082 aluminum alloy, in a 0.3 M sodium chloride (NaCl) aqueous based solution was investigated. The stress corrosion cracking behavior was studied with slow strain rate testing, whereas failure analysis of the fractured surfaces was used to identify the dominant degradation mechanisms. The experimental results clearly indicated that stress corrosion cracking behavior of this aluminum alloy strongly depends on the pH of the solution. In particular, the highest drop in ultimate tensile strength and ductility was observed for the alkaline pH, followed by the acidic, whereas the lowest susceptibility was observed in the neutral pH environment. This observation is attributed to a change in the dominant stress corrosion cracking mechanisms.

Stress-corrosion-cracking of (100)-twist boundaries in Cu-9at.%Al alloy

1990 ◽  
Vol 38 (9) ◽  
pp. 1619-1623 ◽  
Author(s):  
M. Yamashita ◽  
M. Yoshioka ◽  
T. Mimaki ◽  
S. Hashimoto ◽  
S. Miura
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Al Alloy ◽  
Twist Boundaries
Sign in / Sign up

Export Citation Format

Share Document