scholarly journals Effect of strain aging on stress fluctuation accompanied by tensile deformation in 5083 aluminum alloy plate

2007 ◽  
Vol 57 (7) ◽  
pp. 280-285 ◽  
Author(s):  
Yoshihiro NAKAYAMA ◽  
Kakeru YOSHIDA ◽  
Kyohei NOMURA
Keyword(s):  
Aluminum Alloy ◽  
Strain Aging ◽  
Tensile Deformation ◽  
Alloy Plate ◽  
Stress Fluctuation ◽  
Aluminum Alloy Plate ◽  
5083 Aluminum Alloy

scholarly journals Effects of Pre-Tensile Deformation on the Fatigue Fracture Behavior of Annealed 7005 Aluminum Alloy Plate

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 623
Author(s):  
Ni Tian ◽  
Zhen Feng ◽  
Xu Shi ◽  
Wenze Wang ◽  
Kun Liu ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Fatigue Fracture ◽  
Tensile Deformation ◽  
Thin Strip ◽  
Second Phase ◽  
Alloy Matrix ◽  
Alloy Plate ◽  
Dislocation Distribution ◽  
Aluminum Alloy Plate

In the present study, the fatigue life and fatigue fracture characteristics of annealed 7005 aluminum alloy plates subjected to different pre-tensile deformations were investigated. The results obtained upon increasing the pre-tensile deformation of the alloy plate to 20% revealed that the second-phase particles did not show any obvious changes, and that the thickness of the thin strip grain slightly decreased. The dislocation distribution in the alloy matrix varied significantly among the grains or within each grain as the dislocation density gradually increased with increasing pre-tensile deformation. Moreover, the fatigue performance of the annealed 7005 aluminum alloy plate was significantly improved by the pre-tensile deformation, and the alloy plate subjected to 20% pre-tensile deformation exhibited an optimal fatigue life of ~1.06 × 106 cycles, which was 5.7 times and 5.3 times that of the undeformed and 3% pre-stretched alloy plates, respectively. Two fatigue life plateaus were observed in the pre-tensile deformation ranges of 3–5% and 8–12%, which corresponded to heterogeneous dislocation distribution among various grains and within each grain, respectively. Moreover, two large leaps in the plot of the fatigue-life–pre-tensile-deformation curve were observed, corresponding to the pre-tensile deformation ranges of 5–8% and 16–20%, respectively.

scholarly journals Humid Gas Stress Corrosion Cracking in MIG-Welded 5083 Aluminum Alloy Plate

2020 ◽  
Vol 61 (2) ◽  
pp. 330-338
Author(s):  
Alireza Ghorani ◽  
Goroh Itoh ◽  
Tomoyuki Ohbuchi ◽  
Tomoya Kiuchi
Keyword(s):  
Aluminum Alloy ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Alloy Plate ◽  
Aluminum Alloy Plate ◽  
5083 Aluminum Alloy

Investigation of Fatigue Growth Behavior of an Inclined Crack in Aluminum Alloy Plate

2018 ◽  
Vol 18 (5) ◽  
pp. 1159-1167 ◽  
Author(s):  
Jun Wang ◽  
Xing-Quan Zhang ◽  
Wei Wei ◽  
Jin-Yu Tong ◽  
Bin Chen ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Growth Behavior ◽  
Inclined Crack ◽  
Alloy Plate ◽  
Aluminum Alloy Plate

Effect of Residual Aluminum Thickness on Microstructure and Strength of Friction Stir Spot Welded Aluminum Alloy/Copper Lap Joint

2021 ◽  
Vol 1042 ◽  
pp. 3-8
Author(s):  
Mitsuhiro Watanabe ◽  
Shinpei Sasako
Keyword(s):  
Aluminum Alloy ◽  
Pure Copper ◽  
Optical Microscope ◽  
Copper Plate ◽  
Laminate Structure ◽  
Alloy Plate ◽  
Friction Stir ◽  
Residual Aluminum ◽  
Welding Interface ◽  
Aluminum Alloy Plate

Dissimilar metal lap joining of A5052 aluminum alloy plate and C1100 pure copper plate was performed by using friction stir spot welding. The rotating welding tool, which was composed of a probe part and a shoulder part, was plunged from the aluminum alloy plate which was overlapped on the copper plate, and residual aluminum alloy thickness under the probe part of the welding tool after plunging of the welding tool was controlled in the range from 0 mm to 0.4 mm. The strength of the welding interface was evaluated by using tensile-shear test. Microstructure of the welding interface was examined by using an optical microscope and a field emission scanning electron microscope. The welding was achieved at the residual aluminum alloy thickness under the probe part of the welding tool below 0.3 mm. The welded area was formed at aluminum alloy/copper interface located under the probe part of the welding tool, and its width increased with decreasing the residual aluminum alloy thickness. A characteristic laminate structure was produced in the copper matrix near the welding interface. In the joint fabricated at the residual aluminum alloy thickness below 0.1 mm, hook of Cu was formed at edge of the welded area. The fracture did not occur at the welding interface. A remarkable improvement in strength was observed in the joint fabricated at the residual aluminum alloy thickness below 0.1 mm. The formation of laminate structure and hook is considered to result in joint strength improvement.

Study on spray cooling characteristics of 7075 aluminum alloy plate

2022 ◽  
Author(s):  
yongbang miao ◽  
Ruifeng Dou ◽  
Zhi Wen ◽  
Xunliang Liu ◽  
Cheng Zhu
Keyword(s):  
Aluminum Alloy ◽  
Spray Cooling ◽  
7075 Aluminum Alloy ◽  
Alloy Plate ◽  
Aluminum Alloy Plate
Sign in / Sign up

Export Citation Format

Share Document