scholarly journals Age-precipitation behavior in SiC particle dispersed Al-1mass%Mg2Si alloy composite materials.

1997 ◽  
Vol 47 (10) ◽  
pp. 527-532 ◽  
Author(s):  
Susumu IKENO ◽  
Kenji MATSUDA ◽  
Takeshi TERAKI ◽  
Kiyoshi TERAYAMA ◽  
Seichi RENGAKUJI ◽  
...  
Keyword(s):  
Composite Materials ◽  
Alloy Composite ◽  
Precipitation Behavior ◽  
Sic Particle

scholarly journals Age-precipitation in Al2O3 particle/Al-Cu alloy and SiC particle/Al-Cu-Mg alloy composite materials.

1996 ◽  
Vol 46 (1) ◽  
pp. 9-14 ◽  
Author(s):  
Susumu IKENO ◽  
Katsuya FURUTA ◽  
Takeshi TERAKI ◽  
Kenji MATSUDA ◽  
Hiroshi ANADA ◽  
...  
Keyword(s):  
Composite Materials ◽  
Al2o3 Particle ◽  
Mg Alloy ◽  
Alloy Composite ◽  
Cu Alloy ◽  
Sic Particle

Age-hardening Behavior of MgB2 Particle Dispersed Al Alloy Composite Materials

2012 ◽  
pp. 1039-1042
Author(s):  
Chihaya Kawamoto ◽  
Kenji Matsuda ◽  
Satoshi Murakami ◽  
Daisuke Tokai ◽  
Tokimasa Kawabata ◽  
...  
Keyword(s):  
Composite Materials ◽  
Age Hardening ◽  
Al Alloy ◽  
Alloy Composite ◽  
Hardening Behavior

TEM Observation of Interface in Al2O3 Particle Dispersed Al-Mg-Si Alloy Composite Materials

2002 ◽  
Vol 396-402 ◽  
pp. 959-964
Author(s):  
Kenji Matsuda ◽  
Toshimasa Matsuki ◽  
Yasuhiro Uetani ◽  
Susumu Ikeno
Keyword(s):  
Composite Materials ◽  
Alloy Composite

Evaluation of Wear Behavior of Feldspar Particles Reinforced Copper Alloy Composite Materials

2007 ◽  
Vol 539-543 ◽  
pp. 797-802
Author(s):  
B.M. Satish ◽  
B.M. Girish
Keyword(s):  
Composite Materials ◽  
Wear Rate ◽  
Copper Alloy ◽  
Applied Load ◽  
Wear Behavior ◽  
Unreinforced Alloy ◽  
Alloy Composite ◽  
Sliding Speed ◽  
Severe Wear ◽  
Pin On Disc

The wear behavior of unreinforced as well as feldspar particles reinforced copper alloy (phosphor-bronze) composites was studied as a function of sliding speed and applied loads under unlubricated conditions. The content of feldspar particles in the composites was varied from 1- 5% by weight in steps of 2%. A pin-on-disc wear tester was used to evaluate the wear rate. Loads of 20-160 N in steps of 20 N and speeds of 1.25, 1.56, and 1.87 m/s were employed. The results indicated that the wear rate of both the composites and the alloy increased with increase in load and sliding speed. However, the composites exhibited lower wear rate than the alloy. It was found that above a critical applied load, there exists a transition from mild to severe wear both in the unreinforced alloy and in the composites. But the transition loads for the composites were much higher than that of the alloy. The transition loads increase with the increase in weight % of feldspar particles, but decreases with the increase in sliding speeds.

scholarly journals Mechanical Properties of SiC Particle Reinforced Aluminum Alloy Composite

1989 ◽  
Vol 75 (9) ◽  
pp. 1549-1554 ◽  
Author(s):  
Susumu USHIGOME ◽  
Kungi YAMAMOTO ◽  
Tomomi SOEDA
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Alloy Composite ◽  
Sic Particle

Mechanical properties and fractography of zircon-particle-reinforced ZA-27 alloy composite materials

1999 ◽  
Vol 59 (12) ◽  
pp. 1805-1812 ◽  
Author(s):  
S.C. Sharma ◽  
B.M. Girish ◽  
D.R. Somashekar ◽  
Rathnakar Kamath ◽  
B.M. Satish
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Alloy Composite ◽  
Zircon Particle
Sign in / Sign up

Export Citation Format

Share Document