scholarly journals Improvement of material removal rate of Ti-6Al-4V alloy by electrical discharge machining with multiple ultrasonic vibration.

1997 ◽  
Vol 47 (4) ◽  
pp. 220-225 ◽  
Author(s):  
Sung Long CHEN ◽  
Fuang Yuan HUANG ◽  
Yasuo SUZUKI ◽  
Biing Hwa YAN
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

Micro-EDMing of SKD-5 die steel stimulated with magnetic field and ultrasonic vibration

2021 ◽  
pp. 095440892110504
Author(s):  
Gurpreet Singh ◽  
Vivek Sharma
Keyword(s):  
Magnetic Field ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Cumulative Effect ◽  
Machining Performance ◽  
Micro Electrical Discharge Machining

Electrical discharge machining is an essential process in the domain of micromachining. However, many issues need to be solved to implement it in the industrial field. Increasing the machining rate still remains a challenging task in case of micro electrical discharge machining. It becomes impossible to machine a microfeature at a larger depth. Numerous investigators have investigated the positive effect of assistance such as magnetic field and ultrasonic vibration. This paper the discusses machining performance by simultaneously applying the ultrasonic vibration and magnetic field to the machining zone in micro-electrical discharge machining. The process performance is analyzed by measuring the performance characteristics such as material removal rate and taper of the microfeature. The results confirmed that the cumulative effect of each assistance ends in a better material removal rate and low taper of the microfeature.

Investigation of the Spark Cycle Effect on Material Removal Rate in Wire Electrical Discharge Machining

Manufacturing ◽  
2003 ◽  
Author(s):  
Scott F. Miller ◽  
Albert J. Shih
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Short Circuit ◽  
Wire Electrical Discharge Machining ◽  
Time Duration ◽  
Edm Process

The development of new, advanced engineering materials and the needs for precise and flexible prototype and low-volume production have made wire electrical discharge machining (EDM) an important manufacturing process to meet such demand. This research investigates the effect of spark on-time duration and spark on-time ratio, two important EDM process parameters, on the material removal rate (MRR) and surface integrity of four types of advanced material: porous metal foams, metal bond diamond grinding wheels, sintered Nd-Fe-B magnets, and carbon-carbon bipolar plates. An experimental procedure was developed. During the wire EDM, five types of constraints on the MRR due to short circuit, wire breakage, machine slide speed limit, and spark on-time upper and lower limits have been identified. An envelope of feasible EDM process parameters is created and compared across different work-materials. Applications of such process envelope to select process parameters for maximum MRR and for machining of micro features are presented.

CHARACTERIZATION OF ZrB2-SiC COMPOSITES WITH AN ANALYTICAL STUDY ON MATERIAL REMOVAL RATE AND TOOL WEAR RATE DURING ELECTRICAL DISCHARGE MACHINING

2016 ◽  
Vol 40 (3) ◽  
pp. 331-349 ◽  
Author(s):  
S. Sivasankar ◽  
R. Jeyapaul
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Relative Density ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Tool Materials

This research work concentrates on Electrical Discharge Machining (EDM) performance evaluation of ZrB2- SiC ceramic matrix composites with different tool materials at various machining parameters. Monolithic ZrB2 possesses lower relative density (98.72%) than composites. ZrB2 with 20 Vol.% of SiC possesses 99.74% of the relative density with improved hardness values. Bend strength and Young’s modulus increase with SiC addition until it reaches 20 Vol% and then decreasing. EDM performance on tool materials of tungsten, niobium, tantalum, graphite and titanium at various levels of pulse on time and pulse off time are analyzed. Graphite produces the best Material removal rate (MRR) for all the workpieces. Tool wear rate decreases with melting point and thermal conductivity of the tool material.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Sign in / Sign up

Export Citation Format

Share Document