scholarly journals The Effect of Laser Hardening and Embedding Nanoparticles on Tooth Resistance against Caries

2019 ◽  
Vol 9 (1) ◽  
pp. 5-14
Author(s):  
Walid K. Hamoudi et al., Walid K. Hamoudi et al., ◽  
Keyword(s):  
Laser Hardening

scholarly journals Selective laser hardening of injection mould components on multi-axis machining centers

Procedia CIRP ◽  
2020 ◽  
Vol 95 ◽  
pp. 909-914
Author(s):  
Benjamin Peeters ◽  
Olivier Malek ◽  
Sylvie Castagne ◽  
Bert Lauwers
Keyword(s):  
Laser Hardening ◽  
Injection Mould

scholarly journals Process Signature for Laser Hardening

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 465
Author(s):  
Friedhelm Frerichs ◽  
Yang Lu ◽  
Thomas Lübben ◽  
Tim Radel
Keyword(s):  
Residual Stress ◽  
Phase Transformation ◽  
Heating Time ◽  
Temperature Gradients ◽  
Laser Hardening ◽  
Thermal Loads ◽  
Zero Crossing ◽  
Residual Stress State ◽  
Stress Curve ◽  
Process Signature

During many manufacturing processes for surface treatment of steel components heat will be exchanged between the environment and the workpiece. The heat exchange commonly leads to temperature gradients within the surface near area of the workpiece, which involve mechanical strains inside the material. If the corresponding stresses exceed locally the yield strength of the material residual stresses can remain after the process. If the temperature increase is high enough additionally phase transformation to austenite occurs and may lead further on due to a fast cooling to the very hard phase martensite. This investigation focuses on the correlation between concrete thermal loads such as temperature and temperature gradients and resulting modifications such as changes of the residual stress, the microstructure, and the hardness respectively. Within this consideration the thermal loads are the causes of the modifications and will be called internal material loads. The correlations between the generated internal material loads and the material modifications will be called Process Signature. The idea is that Process Signatures provide the possibility to engineer the workpiece surface layer and its functional properties in a knowledge-based way. This contribution presents some Process Signature components for a thermally dominated process with phase transformation: laser hardening. The target quantities of the modifications are the change of the residual stress state at the surface and the position of the 1st zero-crossing of the residual stress curve. Based on Finite Element simulations the internal thermal loadings during laser hardening are considered. The investigations identify for the considered target quantities the maximal temperature, the maximal temperature gradient, and the heating time as important parameters of the thermal loads.

Time-dependent 3D modeling of the thermal analysis of the high-power diode laser hardening process

2020 ◽  
Vol 128 ◽  
pp. 106216 ◽  
Author(s):  
Saeed Talesh Alikhani ◽  
Mohammad Kazemi Zahabi ◽  
Mohammad Javad Torkamany ◽  
Seyed Hasan Nabavi
Keyword(s):  
Thermal Analysis ◽  
Diode Laser ◽  
High Power ◽  
3D Modeling ◽  
Laser Hardening ◽  
Time Dependent ◽  
Hardening Process ◽  
Power Diode ◽  
High Power Diode Laser

A New Computationally Efficient Model for Tempering in Multi-Tracks Laser Hardening

2009 ◽  
Author(s):  
Alessandro Fortunato ◽  
Leonardo Orazi ◽  
Giovanni Tani
Keyword(s):  
Process Parameters ◽  
Laser Power ◽  
Laser Scanning ◽  
Original Model ◽  
Laser Hardening ◽  
Computationally Efficient ◽  
Laser Process ◽  
Treat All ◽  
Tempering Time ◽  
Experimental Comparisons

The bottleneck in laser hardening principally occurs when large surfaces have to be treated because this process situation leads to multi-tracks laser scanning in order to treat all the component surface. Unfortunately, multi-tracks laser trajectories generate an unwanted tempering effect that depends on the overlapping of two close trajectories. To reduce the softening effects, a simulator capable to optimize the process parameters such as laser power and speed, number and types of trajectories, could sensibly increase the applicability of the process. In this paper an original model for the tempering is presented. By introducing a tempering time factor for the martensitic transformation, the hardness reduction can be predicted according to any laser process parameters, material and geometry. Experimental comparisons will be presented to prove the accuracy of the model.

Eddy-current testing of the wear resistance of laser-hardened carburized chromonickel steel and the quality of laser hardening of drill bits

2009 ◽  
Vol 45 (10) ◽  
pp. 698-710 ◽  
Author(s):  
A. V. Makarov ◽  
E. S. Gorkunov ◽  
Yu. M. Kolobylin ◽  
L. Kh. Kogan ◽  
L. G. Korshunov ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Eddy Current ◽  
Eddy Current Testing ◽  
Laser Hardening ◽  
Current Testing ◽  
Drill Bits

Laser hardening of small-diameter shafts of secondarily hardening steels

1988 ◽  
Vol 23 (4) ◽  
pp. 427-428
Author(s):  
Yu. I. Babei ◽  
K. V. Batashov ◽  
V. Y. Beletskii ◽  
M. F. Berezhnitskaya ◽  
S. A. Ivanov ◽  
...  
Keyword(s):  
Small Diameter ◽  
Laser Hardening

scholarly journals Improved manufacturing techniques for RF and laser hardening of missile domes. Phase I. Technical report

1982 ◽  
Author(s):  
W.T. Pawlewicz ◽  
I.B. Mann ◽  
P.M. Martin ◽  
D.D. Hays ◽  
A.G. Graybeal
Keyword(s):  
Phase I ◽  
Laser Hardening ◽  
Technical Report ◽  
Manufacturing Techniques

Laser Hardening of Ring Grooves in Medium Speed Dieselengine Pistons

1986 ◽  
Vol 2 (2) ◽  
pp. 107-114 ◽  
Author(s):  
A. S. Bransden ◽  
S. T.Gazzard ◽  
B. C. Inwood ◽  
J. H. P. C. Megaw
Keyword(s):  
Laser Hardening ◽  
Medium Speed
Sign in / Sign up

Export Citation Format

Share Document