scholarly journals Design approaches for additive manufactured components, with a focus on selective laser melting

2017 ◽  
Vol 50 (3) ◽  
pp. 279-282
Author(s):  
Erin Komi ◽  
Petteri Kokkonen
Keyword(s):  
Selective Laser Melting ◽  
3D Model ◽  
Layer By Layer ◽  
Model Data ◽  
Laser Melting ◽  
Component Design ◽  
Subtractive Manufacturing ◽  
Successful Design ◽  
Manufacturing Techniques ◽  
And Performance

Additive manufacturing (AM) of metal components is characterized by the joining of material particles or feedstock to make parts described by 3D model data in typically a layer by layer fashion [1]. These modern and constantly improving manufacturing techniques inherently allow far more geometric freedom than traditional “subtractive” manufacturing processes, and thus necessitate novel approaches to component design. Careful utilization of this geometric freedom can be translated into products characterized by improved functionality and performance, simplified assemblies, are customizable, and/or lightweight [2-5]. This paper provides a brief overview design approaches, manufacturing limitations, and available tools for successful design of additive manufactured components, with special attention paid to the selective laser melting (SLM) approach.

scholarly journals Influence of 3d-printing parameters on the mechanical properties of 17-4PH stainless steel produced through Selective Laser Melting

2021 ◽  
Vol 15 (58) ◽  
pp. 282-295
Author(s):  
Francesca Romana Andreacola ◽  
Ilaria Capasso ◽  
Letizia Pilotti ◽  
Giuseppe Brando
Keyword(s):  
Stainless Steel ◽  
Selective Laser Melting ◽  
Structural Engineering ◽  
Raw Materials ◽  
Residual Austenite ◽  
Free Form ◽  
Layer By Layer ◽  
Laser Melting ◽  
Subtractive Manufacturing ◽  
Printing Parameters

Additive Manufacturing (AM) is a technological process in which elements are fruitfully built up adding materials layer by layer. AM had a massive development in recent times, thanks to its intrinsic advantages, especially if compared with conventional processes (i.e. subtractive manufacturing methods), in terms of free-form design, high customization of products, a significant reduction in raw materials consumption, low request of postprocessing and heat treatments, use of pure materials and reduced time for final products to be marketed. In order to give an innovative contribution to the knowledge in the field of metal AM materials, this paper reports the main outcomes of an experimental campaign focused on the influence of several specific printing parameters on the mechanical features of the 17-4PH stainless steel, which is one of the most used metal for the Selective Laser Melting (SLM) technology. The influence of different printing directions and sample inclinations on the material mechanical behavior is assessed, with the aim of considering an innovative use in the field of structural engineering. Moreover, the effects due to scanning and recoating times are studied. In addition, the consequences of heat treatment (annealing) on both the residual stresses and the amount of residual austenite are appraised.

Evaluation of geometrical benchmark artifacts containing multiple overhang lengths fabricated using material extrusion technique

2020 ◽  
Vol 14 (3) ◽  
pp. 7296-7308
Author(s):  
Siti Nur Humaira Mazlan ◽  
Aini Zuhra Abdul Kadir ◽  
N. H. A. Ngadiman ◽  
M.R. Alkahari
Keyword(s):  
3D Model ◽  
Laser Scanner ◽  
Dimensional Accuracy ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Layer Technique ◽  
Subtractive Manufacturing ◽  
Manufacturing Features ◽  
Layer Problem

Fused deposition modelling (FDM) is a process of joining materials based on material entrusion technique to produce objects from 3D model using layer-by-layer technique as opposed to subtractive manufacturing. However, many challenges arise in the FDM-printed part such as warping, first layer problem and elephant food that was led to an error in dimensional accuracy of the printed parts especially for the overhanging parts. Hence, in order to investigate the manufacturability of the FDM printed part, various geometrical and manufacturing features were developed using the benchmarking artifacts. Therefore, in this study, new benchmarking artifacts containing multiple overhang lengths were proposed. After the benchmarking artifacts were developed, each of the features were inspected using 3D laser scanner to measure the dimensional accuracy and tolerances. Based on 3D scanned parts, 80% of the fabricated parts were fabricated within ±0.5 mm of dimensional accuracy as compared with the CAD data. In addition, the multiple overhang lengths were also successfully fabricated with a very significant of filament sagging observed.

Study on the Quality and Performance of CoCrMo Alloy Parts Manufactured by Selective Laser Melting

2017 ◽  
Vol 26 (6) ◽  
pp. 2869-2877 ◽  
Author(s):  
Zhang Guoqing ◽  
Yang Yongqiang ◽  
Lin Hui ◽  
Song Changhui ◽  
Zhang Zimian
Keyword(s):  
Selective Laser Melting ◽  
Laser Melting ◽  
Cocrmo Alloy ◽  
And Performance

scholarly journals Fracture Toughness of Hybrid Components with Selective Laser Melting 18Ni300 Steel Parts

2018 ◽  
Vol 8 (10) ◽  
pp. 1879 ◽  
Author(s):  
Luis Santos ◽  
Joel de Jesus ◽  
José Ferreira ◽  
José Costa ◽  
Carlos Capela
Keyword(s):  
Fracture Toughness ◽  
Selective Laser Melting ◽  
Compact Tension ◽  
Powder Materials ◽  
Layer By Layer ◽  
Laser Melting ◽  
Conventional Steel ◽  
Scan Rate ◽  
Aisi H13 ◽  
3D Printed

Selective Laser Melting (SLM) is currently one of the more advanced manufacturing and prototyping processes, allowing the 3D-printing of complex parts through the layer-by-layer deposition of powder materials melted by laser. This work concerns the study of the fracture toughness of maraging AISI 18Ni300 steel implants by SLM built over two different conventional steels, AISI H13 and AISI 420, ranging the scan rate between 200 mm/s and 400 mm/s. The SLM process creates an interface zone between the conventional steel and the laser melted implant in the final form of compact tension (CT) samples, where the hardness is higher than the 3D-printed material but lower than the conventional steel. Both fully 3D-printed series and 3D-printed implants series produced at 200 mm/s of scan rate showed higher fracture toughness than the other series built at 400 mm/s of scan rate due to a lower level of internal defects. An inexpressive variation of fracture toughness was observed between the implanted series with the same parameters. The crack growth path for all samples occurred in the limit of interface/3D-printed material zone and occurred between laser melted layers.

Development of 3D Finite Element Model for Predicting Process-Induced Defects in Additive Manufacturing by Selective Laser Melting (SLM)

2016 ◽  
Author(s):  
Bilal Hussain ◽  
A. Sherif El-Gizawy
Keyword(s):  
Additive Manufacturing ◽  
Laser Beam ◽  
Selective Laser Melting ◽  
Thermal Stresses ◽  
Cost Effective ◽  
Element Model ◽  
Laser Melting ◽  
Two Phase ◽  
Free Process ◽  
Manufacturing Techniques

Selective Laser Melting (SLM) is one of the important Additive Manufacturing techniques for building functional products. Nevertheless, the absence of accurate models for predicting the SLM process behavior, delays development of cost effective and defects free process. This work presents a coupled thermo-mechanical numerical model to capture the two phase (solid-liquid) solidification melting phenomena that occur in the process. The proposed model will also predict the evolvement of process-induced properties and defects particularly residual stresses caused by temperature gradient and thermal stresses. CO2 or Nd:YAG laser beam can be used as a heat source with a Gaussian distribution for the laser beam energy.

scholarly journals Additive Technology Methods for Manufacturing Permanent Magnets

2021 ◽  
Vol 346 ◽  
pp. 01010
Author(s):  
Dmitry Efremov ◽  
Alla Gerasimova ◽  
Nikita Kislykh ◽  
Cristina Shaibel
Keyword(s):  
Selective Laser Melting ◽  
Permanent Magnets ◽  
Magnetic Alloy ◽  
Gas Atomization ◽  
Layer By Layer ◽  
Laser Melting ◽  
Alloy Casting ◽  
Standard Data ◽  
Product Models ◽  
Powder Magnet

The paper presents the results of studying the possibility of using the selective laser melting method for production of permanent magnets. This process allows to manufacture not only product models and prototypes, but also finished functional products by adding material layer by layer and bonding particles and layers to each other. We have considered the application areas of selective laser melting (SLM) based on powders obtained by different methods for the study. In addition, we have analyzed the traditional magnetic alloy casting technology, studied magnetic materials, and compared the powder magnet properties with standard data. We have found that the parameters of powders obtained by gas atomization are qualitatively superior to those of powders obtained using other methods, whereas the resulting magnets meet the requirements for magnets. Based on the 25Kh15KA alloy powder atomized by gas atomization, a SLM plant allows to manufacture permanent magnets with a material density of 7.59–7.55 g/cu.cm, which meets the requirements recommended by the State Standard GOST 24897-81, and to obtain the magnet properties that can be achieved using traditional metallurgical technologies.

Modeling, Simulation and Experimental Validation of Heat Transfer During Selective Laser Melting

2015 ◽  
Author(s):  
Mohammad Masoomi ◽  
Xiang Gao ◽  
Scott M. Thompson ◽  
Nima Shamsaei ◽  
Linkan Bian ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mechanical Properties ◽  
Selective Laser Melting ◽  
Heat Fluxes ◽  
Transient Temperature ◽  
Thermal Gradients ◽  
Layer By Layer ◽  
Metal Powders ◽  
Laser Melting ◽  
Powder Bed

Selective Laser Melting (SLM), a laser powder-bed fusion (PBF-L) additive manufacturing method, utilizes a laser to selectively fuse adjacent metal powders. The powders are aligned in a bed that moves vertically to allow for layer-by-layer part construction-Process-related heat transfer and thermal gradients have a strong influence on the microstructural features, and subsequent mechanical properties, of the parts fabricated via SLM. In order to understand and control the heat transfer inherent to SLM, and to ensure high quality parts with targeted microstructures and mechanical properties, comprehensive knowledge of the related energy and mass transport during manufacturing is required. In this study, the transient temperature distribution within and around parts being fabricated via SLM is numerically simulated and the results are provided to aid in quantify the SLM heat transfer. In order to verify simulation output, and to estimate actual thermal gradients and heat transfer, experiments were separately conducted within a SLM machine using a substrate with embedded thermocouples. The experiments focused on characterizing heat fluxes during initial deposition on an initially-cold substrate and during the fabrication of a thin-walled structure built via stainless steel 17-4 powders. Results indicate that it is important to model heat transfer thorough powder bed as well as substrate.

scholarly journals Fabrication Of Scaffolds From Ti6Al4V Powders Using The Computer Aided Laser Method

2015 ◽  
Vol 60 (2) ◽  
pp. 1065-1070 ◽  
Author(s):  
L.A. Dobrzański ◽  
A.D. Dobrzańska-Danikiewicz ◽  
P. Malara ◽  
T.G. Gaweł ◽  
L.B. Dobrzański ◽  
...  
Keyword(s):  
Selective Laser Melting ◽  
3D Model ◽  
Three Dimensional ◽  
Plaster Cast ◽  
Laser Melting ◽  
Laser Method ◽  
Porous Implant ◽  
Unit Cells ◽  
Dimensional Shape ◽  
3D Solid

AbstractThe aim of the research, the results of which are presented in the paper, is to fabricate, by Selective Laser Melting (SLM), a metallic scaffold with Ti6Al4V powder based on a virtual model corresponding to the actual loss of a patient’s craniofacial bone. A plaster cast was made for a patient with a palate recess, and the cast was then scanned with a 3D scanner to create a virtual 3D model of a palate recess, according to which a 3D model of a solid implant was created using specialist software. The virtual 3D solid implant model was converted into a 3D porous implant model after designing an individual shape of the unit cell conditioning the size and three-dimensional shape of the scaffold pores by multiplication of unit cells. The data concerning a virtual 3D porous implant model was transferred into a selective laser melting (SLM) device and a metallic scaffold was produced from Ti6Al4V powder with this machine, which was subjected to surface treatment by chemical etching. An object with certain initially adopted assumptions, i.e. shape and geometric dimensions, was finally achieved, which perfectly matches the patient bone recesses. The scaffold created was subjected to micro-and spectroscopic examinations.

Sign in / Sign up

Export Citation Format

Share Document