Numerical Simulation on Improving NOx Reduction Efficiency of SNCR by Regulating the 3-D Temperature Field in a Furnace

2013 ◽  
Vol 807-809 ◽  
pp. 1505-1513 ◽  
Author(s):  
Amir A.B. Musa ◽  
Xiong Wei Zeng ◽  
Qing Yan Fang ◽  
Huai Chun Zhou
Keyword(s):  
Numerical Simulation ◽  
Temperature Field ◽  
Removal Efficiency ◽  
Pulverized Coal ◽  
Measuring System ◽  
Optimum Temperature ◽  
Utility Boiler ◽  
Coal Particles ◽  
Injection Zone ◽  
Reduction Efficiency

The optimum temperature within the reagent injection zone is between 900 and 1150°C for the NOX reduction by SNCR (selective non-catalytic reduction) in coal-fired utility boiler furnaces. As the load and the fuel property changes, the temperature within the reagent injection zone will bias from the optimum range, which will reduces significantly the de-NOX efficiency, and consequently the applicability of SNCR technology. An idea to improve the NOX reduction efficiency of SNCR by regulating the 3-D temperature field in a furnace is proposed in this paper. In order to study the new method, Computational fluid dynamics (CFD) model of a 200 MW multi-fuel tangentially fired boiler have been developed using Fluent 6.3.26 to investigate the three-fuel combustion system of coal, blast furnace gas (BFG), and coke oven gas (COG) with an eddy-dissipation model for simulating the gas-phase combustion, and to examine the NOX reduction by SNCR using urea-water solution. The current CFD models have been validated by the experimental data obtained from the boiler for case study. The results show that, with the improved coal and air feed method, average residence time of coal particles increases 0.3s, burnout degree of pulverized coal increases 2%, the average temperature at the furnace nose decreases 61K from 1496K to 1435K, the NO emission at the exit (without SNCR) decreases 58 ppm from 528 to 470 ppm, the SNCR NO removal efficiency increases 10% from 36.1 to 46.1%. The numerical simulation results show that this combustion adjustment method based on 3-D temperature field reconstruction measuring system in a 200 MW multi-fuel tangentially fired utility boiler co-firing pulverized coal with BFG and COG is timely and effective to maintain the temperature of reagent injection zone at optimum temperature range and high NOX removal efficiency of SNCR.

Experimental and numerical investigation of the thermomechanical load on a turbine housing in a radial turbocharger

2021 ◽  
pp. 095440702110521
Author(s):  
Shaolin Chen ◽  
Hong Zhang ◽  
Liaoping Hu ◽  
Guangqing He ◽  
Fen Lei ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Temperature Field ◽  
Fatigue Life ◽  
Simulation Analysis ◽  
Simulation Method ◽  
Testing Temperature ◽  
Experimental Results ◽  
Maximum Temperature ◽  
Monitoring Point ◽  
Turbine Housing

The fatigue life of turbine housing is an important index to measure the reliability of a radial turbocharger. The increase in turbine inlet temperatures in the last few years has resulted in a decrease in the fatigue life of turbine housing. A simulation method and experimental verification are required to predict the life of a turbine housing in the early design and development process precisely. The temperature field distribution of the turbine housing is calculated using the steady-state bidirectional coupled conjugate heat transfer method. Next, the temperature field results are considered as the boundary for calculating the turbine housing temperature and thermomechanical strain, and then, the thermomechanical strain of the turbine housing is determined. Infrared and digital image correlations are used to measure the turbine housing surface temperature and total thermomechanical strain. Compared to the numerical solution, the maximum temperature RMS (Root Mean Square) error of the monitoring point in the monitoring area is only 3.5%; the maximum strain RMS error reached 11%. Experimental results of temperature field test and strain measurement test show that the testing temperature and total strain results are approximately equal to the solution of the numerical simulation. Based on the comparison between the numerical calculation and experimental results, the numerical simulation and test results were found to be in good agreement. The experimental and simulation results of this method can be used as the temperature and strain (stress) boundaries for subsequent thermomechanical fatigue (TMF) simulation analysis of the turbine housing.

The Verification of Geometry Control Method for Cable-Stayed Bridge

2014 ◽  
Vol 1065-1069 ◽  
pp. 992-996
Author(s):  
Can Huang ◽  
Yi Zhi Bu ◽  
Qing Hua Zhang
Keyword(s):  
Numerical Simulation ◽  
Temperature Field ◽  
Energy Method ◽  
Control Method ◽  
Simulation Analysis ◽  
Beam Element ◽  
Integration Process ◽  
Cable Stayed Bridge ◽  
Construction Procedure ◽  
Element Theory

Based on the energy method and beam-element theory, the nonlinear strain are considered, non-stress length and non-stress curvature of element of geometry control method are introducted in the integration process of stain energy. The static equilibrium equation of the geometry control method is established. Take the impacts of structural geometric profile induced by temporary loads and temperature field during the construction procedure are investigated, the correctness of the geometry control method is verified by the numerical simulation analysis.

Sign in / Sign up

Export Citation Format

Share Document