Advanced Fan Out Wafer Level Package Development for Small form Factor and High-Performance Microcontroller Applications

2019 ◽  
Author(s):  
Gaurav Sharma ◽  
Nishant Lakhera ◽  
Mollie Benson ◽  
Andrew J Mawer
Keyword(s):  
Form Factor ◽  
High Performance ◽  
Wafer Level ◽  
Small Form ◽  
Small Form Factor ◽  
Wafer Level Package

scholarly journals High-Performance and Small-Form Factor Near-Field Inductive Coupling for 3-D NoC

2018 ◽  
Vol 26 (12) ◽  
pp. 2921-2934 ◽  
Author(s):  
Srinivasan Gopal ◽  
Sourav Das ◽  
Pawan Agarwal ◽  
Sheikh Nijam Ali ◽  
Deukhyoun Heo ◽  
...  
Keyword(s):  
Form Factor ◽  
High Performance ◽  
Near Field ◽  
Inductive Coupling ◽  
Small Form ◽  
Small Form Factor

Embedded Si Fan Out: A Low Cost Wafer Level Packaging Technology Without Molding and De-bonding Processes

2017 ◽  
Vol 2017 (DPC) ◽  
pp. 1-15
Author(s):  
Hong Xie ◽  
Daquan Yu ◽  
Zhenrui Huang ◽  
Zhiyi Xiao ◽  
Li Yang ◽  
...  
Keyword(s):  
Form Factor ◽  
High Speed ◽  
Low Cost ◽  
High Density ◽  
Wafer Level ◽  
Small Form ◽  
Wafer Level Packaging ◽  
Temporary Bonding ◽  
Small Form Factor ◽  
Si Wafer

The growing and diversifying system requirements have continued to drive the development of a variety of new package technologies and configurations: small form factor, low weight, low profile, high pin count and high speed and low cost. Embedded chip in EMC, also called fan-out wafer-level packaging (FOWLP), has been used in various products such as baseband, RF (radio frequency) transceiver, and PMICs (power management ICs). Currently, INFO technology developed by TSMC®, NANIUM® were in mass production for 3D integration for processor and memory, which inspires other packaging foundries to develop their own embedded FOWLP for the forecasted explosive growth of this market in the next few years. There are a number of challenges for FOWLP. For process point of view, temporary bonding and de-bonding are required. EMC wafers are difficult to handle due to its large warpage driven by the big CTE difference between the Si and molding material. In addition, the manufacturing of fine pitch RDL on EMC surface is also difficult. In this paper, the concept of wafer level embedded Si Fan-Out (eSiFO) technology was introduced and the development progress was reported. For eSiFO, cavities with certain depth were formed by Si dry etch. Then device dies were thinned to designed thickness. The dice were then placed into the cavities and bonded by the attached film on the bottom of the dice. A reconstructed wafer was formed. The micro gap between the chip and sidewall of the cavity as well as the surface of the reconstructed wafer were filled by dry film using vacuum process. Next, the pads were opened, followed RDL fabrication, repassivation, BGA, wafer thinning and dicing. Finally, an eSiFO package was fabricated. There are a number of advantages for eSiFO technology. There is nearly no warpage since the Si was used as reconstruct substrate. The process is relatively simple since no molding, temporary bonding and de-bonding are required. RDL manufacturing is easier on Si wafer vs with molding compounds and can achieve high density routing. Furthermore, it can provide small form factor since the thinning of wafer is the last step. To prove the concept of eSiFO, a 3.3 x 3.3mm package with 50 BGA bumps at 400μm pitch was fabricated. The device wafer was thinned to 100μm. The die size is 1.96 × 2.36mm with pad pitch at about 90μm. The depth of the cavities on 8 in. wafer formed by Bosch process on bare Si wafer was 107μm with 8μm variation. The length and width of Si cavities is 20μm larger than die size. In the package, there is one layer Cu RDL with thickness of 3μm, minimum line width of 13.72μm. The BGA ball diameter is 280μm. All the processes were evaluated and the results showed such packages can be produced. Reliability tests including THS, T/C, HTS and HAST were carried out and no failure issue was observed. Mechanical simulation was used to analyze the stress distribution during TC test and the results showed the maximum stress was located at the RDL near the UBM. In summary, a low cost wafer level fan out technology using reconstructed Si wafer was developed. The process is simple without molding, temporary bonding and de-bonding. The reliability tests of test vehicles proved that such package is reliable. The newly developed eSiFO technology can be widely used for chips requiring fan-Out, small form factor and high density interconnects.

High-Performance and Small Form-Factor Tunable Lasers for High-Capacity Telecom Systems

2019 ◽  
Author(s):  
Luis H. H. de Carvalho ◽  
Giovanni B. de Farias ◽  
Leandro Matiolli ◽  
Flavio Borin ◽  
Juliano R. F. de Oliveira ◽  
...  
Keyword(s):  
Form Factor ◽  
High Performance ◽  
High Capacity ◽  
Tunable Lasers ◽  
Small Form ◽  
Small Form Factor
Sign in / Sign up

Export Citation Format

Share Document