Wear behavior of laser cladded WC-FeAl coating on 321 stainless steel substrate

2020 ◽  
Vol 32 (4) ◽  
pp. 042015
Author(s):  
Alireza Mostajeran ◽  
Reza Shoja-Razavi ◽  
Morteza Hadi ◽  
Mohammad Erfanmanesh ◽  
Hadi Karimi
Keyword(s):  
Stainless Steel ◽  
Stainless Steel Substrate ◽  
Wear Behavior ◽  
Steel Substrate

A Study of Laser Cladding on the NiCr/Cr3C2-WS2-CaF2 Coating

2013 ◽  
Vol 747-748 ◽  
pp. 146-151 ◽  
Author(s):  
Shu Fa Chen ◽  
Cheng Long Feng ◽  
Jin Yang ◽  
Jin Song Chen
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
Composite Coating ◽  
Laser Cladding ◽  
Friction And Wear ◽  
Sliding Friction ◽  
Stainless Steel Substrate ◽  
Wear Behavior ◽  
Steel Substrate ◽  
Wear Process

NiCr/Cr3C2-WS2-CaF2 mixed powders were prepared on 1Cr18Ni9Ti stainless steel substrate to fabricate high-temperature self-lubrication wear resistant composite coating by laser cladding. The microstructure of the coating was examined by means of XRD, SEM and EDS. The high-temperature dry sliding friction and wear behavior of the composite coating were evaluated by using a ball-on-block wear tester at room temperature, 300 and 600 , respectively. The results showed that the composite coating had a unique microstructure consisting of γ-(Ni,Fe) solid solution matrix, Cr7C3/WC reinforcement and CrS/WS2 lubricant particles. The hardness of NiCr/Cr3C2-WS2-CaF2 coating by laser cladding was lower than NiCr/Cr3C2 coating, but higher than stainless steel substrate significantly. It was because of the addition of solid lubricant. In the wear process, elevated temperature was helpful to form a lubricating transfer film. As a result, the NiCr/Cr3C2-WS2-CaF2 coating exhibited a notable anti-friction and wear resistance at 300 and 600 .

Vibration based Energy Harvester Employing ZnO Film on the Stainless Steel Substrate

2013 ◽  
Vol 133 (4) ◽  
pp. 126-127 ◽  
Author(s):  
Shota Hosokawa ◽  
Motoaki Hara ◽  
Hiroyuki Oguchi ◽  
Hiroki Kuwano
Keyword(s):  
Stainless Steel ◽  
Energy Harvester ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Zno Film

Preparation of β-PbO2 and β-PbO2-MnO2 Coating on Stainless Steel Substrate

2012 ◽  
Vol 490-495 ◽  
pp. 3486-3490
Author(s):  
Qiang Yu ◽  
Zhen Chen ◽  
Zhong Cheng Guo
Keyword(s):  
Stainless Steel ◽  
Mass Fraction ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Substrate Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
New Type ◽  
Plating Solution ◽  
Element Mass Fraction

In order to prepare a new type of anode material, stainless steel was selected as substrate material. The β-PbO2 coating on stainless steel substrate was prepared under the appropriate plating solution, and the PbO2-MnO2 coating was prepared with thermal decomposition. The crystal structure was determined by X-ray diffraction; Surface morphology was test by Scanning Electron Microscopy; the energy spectrum was used to determine element mass-fraction and the ratio of atomic number of the coatings.

Studies on grain boundary effects in spray deposited BICOVOX 0.1 films on platinum-coated stainless steel substrate

Ionics ◽  
2010 ◽  
Vol 17 (1) ◽  
pp. 69-74 ◽  
Author(s):  
Rajeev Joshi ◽  
Ratikant Mishra ◽  
C. A. Betty ◽  
Shilpa Sawant ◽  
S. H. Pawar
Keyword(s):  
Stainless Steel ◽  
Grain Boundary ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Boundary Effects ◽  
Grain Boundary Effects

scholarly journals Samarium electrodeposited acetate and oxide thin films on stainless steel substrate characterized by XPS

2016 ◽  
Vol 23 (1) ◽  
pp. 70-81 ◽  
Author(s):  
Kristian Myhre ◽  
Jonathan Burns ◽  
Harry Meyer ◽  
Nathan Sims ◽  
Rose Boll
Keyword(s):  
Thin Films ◽  
Stainless Steel ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Oxide Thin Films
Sign in / Sign up

Export Citation Format

Share Document