Experimental investigation on the cut front geometry in the inert gas laser fusion cutting with disk and CO2 lasers

2011 ◽  
Author(s):  
Leonardo Daniele Scintilla ◽  
Luigi Tricarico ◽  
Achim Mahrle ◽  
Andreas Wetzig ◽  
Eckhard Beyer
Keyword(s):  
Experimental Investigation ◽  
Inert Gas ◽  
Laser Fusion ◽  
Co2 Lasers ◽  
Gas Laser ◽  
Laser Fusion Cutting

Analysis of process efficiency in laser fusion cutting and some single- and multi-objective optimization aspects

2021 ◽  
pp. 095440892110627
Author(s):  
Miloš Madić ◽  
Mohamed H Gadallah ◽  
Dušan Petković
Keyword(s):  
Laser Power ◽  
Laser Cutting ◽  
Optimization Problem ◽  
Removal Rate ◽  
Cutting Speed ◽  
Process Efficiency ◽  
Laser Fusion ◽  
Cut Quality ◽  
Dross Formation ◽  
Laser Fusion Cutting

For an efficient use of laser cutting technology, it is of great importance to analyze the impact of process parameters on different performance indicators, such as cut quality criteria, productivity criteria, costs as well as environmental performance criteria (energy and resource efficiency). Having this in mind, this study presents the experimental results of CO2 laser fusion cutting of AISI 304 stainless steel using nitrogen, with the aim of developing a semi-empirical mathematical model for the estimation of process efficiency as an important indicator of the achievable energy transfer efficiency in the cutting process. The model was developed by relating the theoretical power needed to melt the volume per unit time and used laser power, where the change of kerf width was modeled using an empirical power model in terms of laser cutting parameters such as laser power, cutting speed, and focus position. The obtained results indicated the dominant effect of the focus position on the change in process efficiency, followed by the cutting speed and laser power. In addition, in order to maximize process efficiency and simultaneously ensure high cut quality without dross formation, a laser cutting optimization problem with constraints was formulated and solved. Also, a multi-objective optimization problem aimed at simultaneous optimization of process efficiency and material removal rate was formulated and solved, where the determined set of Pareto non-dominated solutions was analyzed by using the entropy method and multi-criteria decision analysis method, that is, the Technique for Order of Preference by Similarity to Ideal Solution. The optimization results revealed that in order to enhance process efficiency and material removal rate, while ensuring high cut quality without dross formation, focusing the laser beam deep into the bulk of material is needed with particular trade-offs between laser power and cutting speed levels at high pressure levels of nitrogen.

Investigation on the melt ejection and burr formation during laser fusion cutting of stainless steel

2020 ◽  
Vol 32 (2) ◽  
pp. 022068 ◽  
Author(s):  
S. Stoyanov ◽  
D. Petring ◽  
D. Arntz-Schroeder ◽  
M. Günder ◽  
A. Gillner ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Burr Formation ◽  
Laser Fusion ◽  
Laser Fusion Cutting ◽  
Melt Ejection

scholarly journals Transition from Stable Laser Fusion Cutting Conditions to Incomplete Cutting Analysed with High-speed X-ray Imaging

2020 ◽  
Vol 60 ◽  
pp. 470-480
Author(s):  
Jannik Lind ◽  
Florian Fetzer ◽  
Christian Hagenlocher ◽  
David Blazquez-Sanchez ◽  
Rudolf Weber ◽  
...  
Keyword(s):  
High Speed ◽  
Cutting Conditions ◽  
Laser Fusion ◽  
X Ray ◽  
X Ray Imaging ◽  
Laser Fusion Cutting ◽  
Stable Laser
Sign in / Sign up

Export Citation Format

Share Document