Effect of heat input on the positional tolerances of wire feeding during laser welding

1995 ◽  
Author(s):  
A.S. Salminen ◽  
V.P. Kujanpää
Keyword(s):  
Laser Welding ◽  
Heat Input ◽  
Wire Feeding

scholarly journals Research on Parameters of Wire-Filling Laser Welding and Quenching Process for Joints Microstructure and Mechanical Property of BR1500HS Steel

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1047
Author(s):  
Lianpu Zhou ◽  
Chundong Zhu ◽  
Rongfei Ma ◽  
Zihao Wei
Keyword(s):  
Laser Welding ◽  
Heat Input ◽  
Retained Austenite ◽  
Fracture Morphology ◽  
Boron Steel ◽  
Test Machine ◽  
Quenching Process ◽  
Feeding Speed ◽  
Wire Feeding ◽  
Grain Diameter

With the aim to investigate the effect of parameters and the quenching process on the joint microstructure and mechanical properties of hot stamping steel by laser welding, BR1500HS boron steel was welded by wire-filling laser welding with ER70-G welding wire under different parameters. The welded specimens were heated to 900 °C and held for 5 min before water quenching. A universal material test machine, optical microscope, Vickers hardness tester, scanning electron microscope, and electron backscatter diffraction (EBSD) were used to characterize. The results show that the heat input should be greater than 1040 J/cm and the optimal wire-feeding speed is between 160 cm/min and 180 cm/min. The tensile strength of the quenched joint can reach greater than 1601.9 MPa at compatible parameters. More retained austenite distributes in the fusion zone (FZ) and fine grain zone (FGZ) than the coarse grain zone (CGZ) before quenching. However, the retained austenite in FZ and heat-affected zone (HAZ) decreases clearly and distributes uniformly after quenching. The grain diameter in FZ before quenching is not uniform and there are some coarse grains with the diameter greater than 40 μm. After quenching, the grains are refined and grain diameter is more uniform in the joint. With the increase in heat input, the microhardness of FZ and HAZ before quenching decreases from 500 HV to 450 HV. However, if the wire-feeding speed increases, the microhardness of FZ and HAZ before quenching increases from 450 HV to 500 HV. After quenching, the joint microhardness of all samples is between 450 HV and 550 HV. The fracture morphology of the joint before quenching consists of a large number of dimples and little river patterns. After quenching, the fracture morphology consists of a large amount of river patterns and cleavage facets due to the generation of martensite.

scholarly journals Development of laser welding of high strength aluminium alloy 2024-T4 with controlled thermal cycle

2020 ◽  
Vol 326 ◽  
pp. 08005
Author(s):  
Mete Demirorer ◽  
Wojciech Suder ◽  
Supriyo Ganguly ◽  
Simon Hogg ◽  
Hassam Naeem
Keyword(s):  
Laser Beam ◽  
Laser Welding ◽  
Heat Input ◽  
Thermal Cycle ◽  
Laser Beam Welding ◽  
Base Material ◽  
High Strength ◽  
Cooling Rates ◽  
Aa 2024 ◽  
Welding Processes

An innovative process design, to avoid thermal degradation during autogenous fusion welding of high strength AA 2024-T4 alloy, based on laser beam welding, is being developed. A series of instrumented laser welds in 2 mm thick AA 2024-T4 alloys were made with different processing conditions resulting in different thermal profiles and cooling rates. The welds were examined under SEM, TEM and LOM, and subjected to micro-hardness examination. This allowed us to understand the influence of cooling rate, peak temperature, and thermal cycle on the growth of precipitates, and related degradation in the weld and heat affected area, evident as softening. Although laser beam welding allows significant reduction of heat input, and higher cooling rates, as compared to other high heat input welding processes, this was found insufficient to completely supress coarsening of precipitate in HAZ. To understand the required range of thermal cycles, additional dilatometry tests were carried out using the same base material to understand the time-temperature relationship of precipitate formation. The results were used to design a novel laser welding process with enhanced cooling, such as with copper backing bar and cryogenic cooling.

Determination of Heat Input in Tungsten Inert Gas and Laser Welding of Type Optim 960 QC Structural Steel Using Adams’ Equation for 2-D Heat Distribution

2017 ◽  
Vol 750 ◽  
pp. 45-52
Author(s):  
Sveto Cvetkovski
Keyword(s):  
Laser Welding ◽  
Heat Input ◽  
Arc Welding ◽  
Research Work ◽  
Laser Beam Welding ◽  
Peak Temperature ◽  
Efficiency Coefficient ◽  
Zone Recrystallization ◽  
Welding Processes

The heat input during conventional arc welding processes can be readily calculated knowing the power taken from the power source. The efficiency coefficient can be taken from the appropriate literature standards. Here, the intention of the performed research work was to develop a procedure for determination of heat input in arc and laser welding processes implementing Adams equation - modified Rykalin equation for two dimensional heat distributions (2-D). To realize this idea, it is necessary to determine two characteristic temperatures points in the HAZ with known peak temperature, and to determine distance between them. Implementing measured values for distance in Adams’ equation, heat input in arc welding can be directly determined in arc welded joints.In laser beam welding, the absorption of the beam in the metal is not known, so that the welding heat input cannot be calculated directly, and direct implementation of Adam’s equation is not possible i.e. absorption coefficient has to be determined first, and after that calculation of heat input is possible.The peak temperatures corresponding to specific microstructures can be obtained by performing welding simulation, by the Gleeble 1500 simulator in our case. As one of the peak temperatures, the melting temperature can be used corresponding to the fusion line, so that at least one characteristic peak temperature such as coarse grain zone, fine grin zone, intercritical zone, recrystallization, has to be determined by the simulation.Performed research showed that obtained values for heat input using Adam’s equation correspond pretty well with standard equation for heat input in arc welding.

Advances in joining technologies for the innovation of 21st century lightweight aluminium-CFRP hybrid structures

2022 ◽  
pp. 095440892110730
Author(s):  
Renangi Sandeep ◽  
Arivazhagan Natarajan
Keyword(s):  
Shear Strength ◽  
Laser Welding ◽  
Heat Input ◽  
Mechanical Performance ◽  
Current Knowledge ◽  
Ultrasonic Welding ◽  
Hybrid Structures ◽  
Joint Shear Strength ◽  
Hybrid Joints ◽  
Welding Processes

In the twenty-first century, the application of carbon fiber reinforced polymer (CFRP) materials in the vehicle industry are growing rapidly due to lightweight, high specific strength, and elasticity. In the automobile and aerospace industries, CFRP needs to be joined with metals to build complete structures. The demand for hybrid structures has prompted research into the combination of CFRP and metals in manufacturing. Aluminium and CFRP structures combine the mechanical properties of aluminium with the superior physical and chemical properties of CFRP. However, joining dissimilar materials is often challenging to achieve. Various joining technologies are developed to produce hybrid joints of CFRP, and aluminium alloys include conventional adhesives, mechanical and thermal joining technologies. In this review article, an extensive review was carried out on the thermal joining technologies include laser welding, friction-based welding technologies, ultrasonic welding, and induction welding processes. The article primarily focused on the current knowledge and process development of these technologies in fabricating dissimilar aluminium and CFRP structures. Besides, according to Industry 4.0 requirements, additive manufacturing-based techniques to fabricate hybrid structures are presented. Finally, this article also addressed the various improvements for the future development of these joining technologies. Ultrasonic welding yields the maximum shear strength among the various hybrid joining technologies due to lower heat input. On the other hand, laser welding produces higher heat input, which deteriorates the mechanical performance of the hybrid joints. Surface pretreatments on material surfaces prior to joining showed a significant effect on joint shear strength. Surface modification using anodizing is considered an optimal method to improve wettability, increasing mechanical interlocking phenomena.

Characteristics of the Keyhole and Energy Absorption during YAG Laser Welding of Al-Li Alloy

2011 ◽  
Vol 287-290 ◽  
pp. 2401-2406 ◽  
Author(s):  
Ai Qin Duan ◽  
Shui Li Gong
Keyword(s):  
Laser Welding ◽  
Heat Input ◽  
High Speed ◽  
Laser Energy ◽  
Welding Parameters ◽  
High Speed Camera ◽  
Welding Time ◽  
Welding Condition ◽  
Yag Laser ◽  
Temperature Area

In this paper, the keyhole of YAG laser welding 5A90 Al-Li alloy was observed and measured through the high speed camera. The characteristics of the keyhole and the effects of welding parameters were studied. The characteristics of the absorption of laser energy and the susceptivity for heat input in welding 5A90 were given. The results show that in this welding condition, the keyhole of laser welding 5A90 is nearly a taper and the highest temperature area is in the bottom. There are clear effects of heat input on the characteristics, especially the surface radius of keyhole and plasma/vapor in keyhole. Another phenomena is observed that sometime plasma/vapor could disappear in 0.3ms welding time, and this feature will be more remarkable as decrease of heat input. It shows that the absorption of energy is unsteady. It is known that when this instability reaches a certain value, an unsteady weld will be formed.

Numerical Analysis of Solidification Behavior during Laser Welding Nickel-Based Single-Crystal Superalloy Part: II Crystallography-Dependent Supersaturation of Liquid Aluminum

2021 ◽  
Vol 1018 ◽  
pp. 13-22
Author(s):  
Zhi Guo Gao
Keyword(s):  
Laser Welding ◽  
Single Crystal ◽  
Weld Pool ◽  
Welding Speed ◽  
Heat Input ◽  
Laser Power ◽  
Liquid Aluminum ◽  
Dendrite Growth ◽  
Solidification Cracking ◽  
Solid Liquid Interface

The thermal metallurgical modeling of liquid aluminum supersaturation was further developed through couple of heat transfer model, dendrite selection model, multicomponent dendrite growth model and nonequilibrium solidification model during three-dimensional nickel-based single-crystal superalloy weld pool solidification. The welding configuration plays more important role in supersaturation of liquid aluminum, morphology instability and nonequilibrium partition behavior. The bimodal distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically symmetrical about the weld pool centerline in (001) and [100] welding configuration. The distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically asymmetrical throughout the weld pool in (001) and [110] welding configuration. Optimum low heat input (low laser power and high welding speed) with (001) and [100] welding configuration is more favored to predominantly promote epitaxial [001] dendrite growth to reduce the metallurgical factors for solidification cracking than that of high heat input (high laser power and slow welding speed) with (001) and [110] welding configuration. The lower the heat input is used, the lower supersaturation of liquid aluminum is imposed, and the smaller size of vulnerable [100] dendrite growth region is incurred to ameliorate solidification cracking susceptibility and vice versa. The overall supersaturation of liquid aluminum in (001) and [100] welding configuration is beneficially smaller than that of (001) and [110] welding configuration regardless of heat input, and is not thermodynamically relieved by gamma prime γˊ phase. (001) and [110] welding configuration is detrimental to weldability and deteriorates the solidification cracking susceptibility because of unfavorable crystallographic orientations and alloying aluminum enrichment. The mechanism of asymmetrical solidification cracking because of crystallography-dependent supersaturation of liquid aluminum is proposed. The eligible solidification cracking location is particularly confined in [100] dendrite growth region. Moreover, the theoretical predictions agree well with the experiment results. The useful modeling is also applicable to other single-crystal superalloys with similar metallurgical properties for laser welding or laser cladding. The thorough numerical analyses facilitate the understanding of weld pool solidification behavior, microstructure development and solidification cracking phenomena in the primary γ phase, and thereby optimize the welding conditions (laser power, welding speed and welding configuration) for successful crack-free laser welding.

scholarly journals Effect of Heat Input on Porosity Defects in a Fiber Laser Welded Socket-Joint Made of Powder Metallurgy Molybdenum Alloy

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1433 ◽  
Author(s):  
Miao-Xia Xie ◽  
Yan-Xin Li ◽  
Xiang-Tao Shang ◽  
Xue-Wu Wang ◽  
Jun-Yu Pei
Keyword(s):  
Computed Tomography ◽  
Powder Metallurgy ◽  
Laser Welding ◽  
Fiber Laser ◽  
Heat Input ◽  
Dominant Role ◽  
Fusion Welding ◽  
Fiber Laser Welding ◽  
Welding Heat Input ◽  
Porosity Defects

Porosity defects are still a challenging issue in the fusion welding of molybdenum and its alloys due to the pre-existing interior defects associated with the powder metallurgy process. Fiber laser welding of end plug and cladding tube made of nanostructured high-strength molybdenum (NS-Mo) alloy was performed in this work with an emphasis on the role of welding heat input. The distribution and morphology of porosity defects in the welded joints were examined by computed tomography (CT) and scanning electron microscopy (SEM). Preliminary results showed that laser welding of NS-Mo under low heat input significantly reduced the porosity defects in the fusion zone. The results of computed tomography (CT) showed that when the welding heat input decreased from 3600 J/cm (i.e., 1200 W, 0.2 m/min) to 250 J/cm (i.e., 2500 W, 6 m/min), the porosity ratio of the NS-Mo joints declined from 10.7% to 2.1%. Notable porosity defects under high heat input were related to the instability of the keyhole, expansion and the merging of bubbles in the molten pool, among which the instability of the keyhole played the dominant role. The porous defects at low heat input were generated as bubbles released from the powder metallurgy base metal (BM) did not have enough time to overflow and escape.

scholarly journals Wire-Feeding Laser Welding of Copper/Stainless Steel Using Different Filler Metals

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2122
Author(s):  
Xiaoyan Gu ◽  
Ziwei Cui ◽  
Xiaopeng Gu ◽  
Jiaxu Shao
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Laser Welding ◽  
Large Deformation ◽  
Grain Refinement ◽  
Filler Metal ◽  
Weld Interface ◽  
Grain Sizes ◽  
Filled Joint ◽  
Wire Feeding

Ni-based filler metal and Ni-Cu-based filler metal were used to obtain copper/stainless steel (Cu/SS) joints through wire-feeding laser welding. Along the SS/weld interface, there exist different grain sizes (from coarse columnar grains to fine equiaxed grains). The heat affected zone (HAZ) on the copper side consisted of two areas with different grain sizes and the size of the grain in the Cu-HAZ of the Ni-Cu-based filled joint was much smaller than that of the Ni-based filled joint. Our results showed that grain refinement at the copper/weld (Cu/weld) interface of the Ni-Cu-based filled joint was observed through high-resolution electron backscattered diffraction (EBSD). There was a hardness elevation at the Cu/weld interface of the Ni-Cu-based filled joint due to the grain refinement on the weld of the copper side. The maximum tensile strength of the Ni-Cu-based filled joint was obtained and reached 91.2% of the tensile strength of the copper base metal (Cu-BM). Joints in this study were observed to fracture in a ductile mode. Furthermore, the Ni-Cu-based filled joint exhibited a higher plastic deformation, which was primarily caused by the large deformation of the weld zone and the large deformation of the Cu-BM due to the high plasticity of the weld, which alleviated the stress concentration, as indicated by 2D-digital image correlation (DIC) test results.

Sign in / Sign up

Export Citation Format

Share Document