Laser cutting of carbon fiber-reinforced plastic with an absorber transparent for visible spectrum

2015 ◽  
Vol 27 (3) ◽  
pp. 032003 ◽  
Author(s):  
M. Canisius ◽  
D. Herzog ◽  
M. Schmidt-Lehr ◽  
M. Oberlander ◽  
J. Direnga ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Laser Cutting ◽  
Visible Spectrum ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

Laser cutting of carbon fiber reinforced plastic using a 30 kW fiber laser

2015 ◽  
Vol 27 (S2) ◽  
pp. S28001 ◽  
Author(s):  
Dirk Herzog ◽  
Matthias Schmidt-Lehr ◽  
Marten Canisius ◽  
Max Oberlander ◽  
Jan-Philipp Tasche ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Laser ◽  
Laser Cutting ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

scholarly journals Stressing State Analysis of Reinforced Concrete Beam Strengthened by CFRP Sheet with Anchoring Device

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 576
Author(s):  
Liang Luo ◽  
Jie Lai ◽  
Jun Shi ◽  
Guorui Sun ◽  
Jie Huang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Strain Distribution ◽  
Carbon Fiber Reinforced Plastic ◽  
Rc Beams ◽  
Fiber Reinforced ◽  
Strain Distribution Pattern ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Cfrp Sheet ◽  
Carbon Fiber Reinforced

This paper investigates the working performance of reinforcement concrete (RC) beams strengthened by Carbon-Fiber-Reinforced Plastic (CFRP) with different anchoring under bending moment, based on the structural stressing state theory. The measured strain values of concrete and Carbon-Fiber-Reinforced Plastic (CFRP) sheet are modeled as generalized strain energy density (GSED), to characterize the RC beams’ stressing state. Then the Mann–Kendall (M–K) criterion is applied to distinguish the characteristic loads of structural stressing state from the curve, updating the definition of structural failure load. In addition, for tested specimens with middle anchorage and end anchorage, the torsion applied on the anchoring device and the deformation width of anchoring device are respectively set parameters to analyze their effects on the reinforcement performance of CFRP sheet through comparing the strain distribution pattern of CFRP. Finally, in order to further explore the strain distribution of the cross-section and analyze the stressing-state characteristics of the RC beam, the numerical shape function (NSF) method is proposed to reasonably expand the limited strain data. The research results provide a new angle of view to conduct structural analysis and a reference to the improvement of reinforcement effect of CFRP.

Study on the mechanism of inhomogeneous microdamage in short-pulse laser processing of carbon fiber reinforced plastic

2021 ◽  
pp. 073168442098359
Author(s):  
Luyao Xu ◽  
Jiuru Lu ◽  
Kangmei Li ◽  
Jun Hu
Keyword(s):  
Carbon Fiber ◽  
Pulse Energy ◽  
Short Pulse ◽  
Heterogeneous Material ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Processing Efficiency ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

In this article, a micro-heterogeneous material simulation model with carbon fiber and resin phase about laser ablation on carbon fiber reinforced plastic (CFRP) is established by Ansys. The ablation process of CFRP by nanosecond ultraviolet laser is simulated, and the mechanism of pulse energy and spot spacing on the heat-affected zone (HAZ) is studied, then the process parameters are optimized with the goal of HAZ size and processing efficiency, and finally the validity of the model is verified by experiments. It is found that the residual gradient and the width of the radial HAZ increase with the increase of the spot spacing, and the width of the axial HAZ decreases slightly with the increase of the spot spacing, which indicates the existence of the optimal spot spacing. Second, the ablation depth increases with the increase of the pulse energy, and the carbon fiber retains a relatively complete degree of exposure when the pulse energy is low, which has a certain guiding significance for the cleaning and bonding of CFRP.

Sign in / Sign up

Export Citation Format

Share Document