Bond Strength Stability of Self-adhesive Resin Cement to Etched Vitrified Yttria-stabilized Tetragonal Zirconia Polycrystal Ceramic After Thermomechanical Cycling

2019 ◽  
Vol 44 (5) ◽  
pp. 545-555 ◽  
Author(s):  
EV Maroun ◽  
JGA Guimarães ◽  
WG de Miranda ◽  
LRC Netto ◽  
AB Elias ◽  
...  
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Adhesive Resin ◽  
Thermomechanical Cycling ◽  
Significant Difference ◽  
Ceramic Blocks ◽  
Adhesive Resin Cement ◽  
Tetragonal Zirconia Polycrystal

SUMMARY The purpose of this study was to evaluate the influence of thermomechanical cycling on the bond strength stability of self-adhesive resin cement to vitrified yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic. Y-TZP ceramic blocks were divided into four groups according to the surface treatments: AS, as sintered; SB, sandblasted with 50-μm Al2O3 particles; LG, vitrification with a low-fusing glaze and etching with 10% hydrofluoric acid; and HC, vitrification with a ceramic liner and etching with 10% hydrofluoric acid. Lithium disilicate ceramic blocks etched with 10% hydrofluoric acid for 20 seconds (EM) were also tested. Blocks of resin composite were cemented on the ceramic block surfaces using a self-adhesive resin cement. Half of the blocks from each group were cut into beams and submitted to microtensile bond strength (μTBS) testing after immersion in water at 37°C for 24 hours and the other half after mechanical (1,200,000 cycles, 98 N, 2.5 Hz) and thermal (10,000 cycles, 5-55°C, 30-second dwell time) cycling (TMC). Data were analyzed using one-way analysis of variance, Tukey's honest significant difference post hoc test, and Student t-test (α=0.05). After 24 hours, EM and LG presented similar and the highest μTBS, whereas AS showed the lowest μTBS (p<0.05). After TMC, EM presented the highest μTBS, followed by LG (p<0.05). Only EM and LG maintained the stability of μTBS after TMC (p>0.05). The bonding to Y-TZP ceramic vitrified with a low-fusing glaze withstood thermomechanical cycling.

The Effect of Sandblasting and Different Primers on Shear Bond Strength Between Yttria-tetragonal Zirconia Polycrystal Ceramic and a Self-adhesive Resin Cement

2015 ◽  
Vol 40 (1) ◽  
pp. 63-71 ◽  
Author(s):  
Y-A Yi ◽  
J-S Ahn ◽  
Y-J Park ◽  
S-H Jun ◽  
I-B Lee ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Xrd Analysis ◽  
Resin Cement ◽  
Air Abrasion ◽  
Adhesive Resin ◽  
Multiple Comparison Test ◽  
Adhesive Resin Cement ◽  
Tetragonal Zirconia Polycrystal

SUMMARY Purpose To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. Methods and Materials Y-TZP ceramic surfaces were ground flat with 600-grit silicon carbide paper and then divided into seven groups of 10 and treated as follows: untreated (control), Monobond Plus, Z-PRIME Plus, ESPE Sil with CoJet, air-abrasion, Monobond Plus with air-abrasion, and Z-PRIME Plus with air-abrasion. Self-adhesive resin cement was placed onto the treated Y-TZP specimens for each group. All specimens were thermocycled and subjected to a shear bond strength test. Scanning electron microscope images of the fractured areas and x-ray diffraction (XRD) analysis of the surface-treated Y-TZP specimens were performed. Data were statistically analyzed using one-way analysis of variance and the Student-Newman-Keuls multiple comparison test (p<0.05). Results The Z-PRIME Plus treatment in combination with air-abrasion produced the highest bond strength (16.50±2.26 MPa), followed by air-abrasion (10.56±3.32 MPa), and then Monobond Plus combined with air-abrasion (8.93±3.13 MPa), ESPE Sil after CoJet application (8.54±3.98 MPa), and the Z-PRIME Plus group (8.27±2.79 MPa). The control (3.91±0.72 MPa) and Monobond Plus (4.86±1.77 MPa) groups indicated the lowest results (p<0.05). The XRD results showed the peaks of the monoclinic phase for the air-abrasion and CoJet treatment groups compared with the Y-TZP control. Conclusion Z-PRIME Plus primer application after air-abrasion presented the best results for improving the bond strength between Y-TZP ceramic and self-adhesive resin cement.

scholarly journals Influence of Different Surface Pretreatments on Shear Bond Strength of an Adhesive Resin Cement to Various Zirconia Ceramics

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 652 ◽  
Author(s):  
Marco Colombo ◽  
Simone Gallo ◽  
Sara Padovan ◽  
Marco Chiesa ◽  
Claudio Poggio ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Zirconia Ceramic ◽  
Adhesive Resin ◽  
Surface Pretreatment ◽  
Significant Difference ◽  
Computer Aided ◽  
Adhesive Resin Cement

The aim of this in vitro study was to assess the influence of surface pretreatment on shear bond strength (SBS) of an adhesive resin cement (G-CEM Link Force TM, GC Corporation, Tokyo, Japan) to three different yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) ceramics: (1) Copran Zirconia Monolith HT, COP; (2) Katana ML Zirconia, KAT; and (3) Metoxit Z-CAD HTL Zirconia, MET. In total, 45 cylinders (5 mm in diameter, 1 mm height) for each type of zirconia ceramic were prepared used a computer-aided design and computer-aided manufacturing (CAD/CAM) machine (software CEREC 4.2). Each type of zirconia was subdivided into three groups and each group received a different surface pretreatment; 15 samples were not conditioned as control (groups COP 1, KAT 1, MET 1), 15 samples were air-borne particle abraded with aluminum dioxide particles of 50-μm size at 0.3 MPa for 20 s (groups COP 2, KAT 2, MET 2), and 15 samples were hot-etched with a solution of hydrochloric acid and ferric chloride (groups COP 3, KAT 3, MET 3). After specimen fabrication, the adhesive cement–ceramic interface was analyzed using an SBS test. Subsequently, the adhesive remnant index (ARI) was measured. Data were submitted to statistical analysis. Air-borne particle abraded specimens showed the highest SBS values for COP and KAT groups. For MET, no significant difference was reported between air-borne particle abraded specimens and untreated controls. The lowest values were detected for acid-etched groups. A higher frequency of ARI = “1” and ARI = “2” was reported in control and air-borne particle abraded groups, whereas ARI = “3” was detected in hot-etched groups. No correlation was found between ARI score and shear bond strength. Air-borne particle abrasion is considered the best treatment for Zirconia Copran and Zirconia Katana ML, if it is followed by using dual-curing resin cement.

Development of a Cavity Disinfectant Containing Antibacterial Monomer MDPB

2016 ◽  
Vol 95 (13) ◽  
pp. 1487-1493 ◽  
Author(s):  
N. Hirose ◽  
R. Kitagawa ◽  
H. Kitagawa ◽  
H. Maezono ◽  
A. Mine ◽  
...  
Keyword(s):  
Antibacterial Activity ◽  
Bond Strength ◽  
Bacterial Species ◽  
Oral Bacteria ◽  
Resin Cement ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Significant Difference ◽  
Adhesive Resin Cement

An experimental cavity disinfectant (ACC) that is intended to be used for various direct and indirect restorations was prepared by adding an antibacterial monomer 12-methacryloyloxydodecylpyridinum bromide (MDPB) at 5% into 80% ethanol. The antibacterial effectiveness of ACC and its influences on the bonding abilities of resin cements were investigated. To examine the antibacterial activity of unpolymerized MDPB, the minimum inhibitory and bactericidal concentrations (MIC and MBC) were determined for Streptococcus mutans, Lactobacillus casei, Actinomyces naeslundii, Parvimonas micra, Enterococcus faecalis, Fusobacterium nucleatum, and Porphyromonas gingivalis. Antibacterial activities of ACC and the commercial cavity disinfectant containing 2% chlorhexidine and ethanol (CPS) were evaluated by agar disk diffusion tests through 7 bacterial species and by MIC and MBC measurement for S. mutans. The effects of ACC and CPS to kill bacteria in dentinal tubules were compared with an S. mutans–infected dentin model. Shear bond strength tests were used to examine the influences of ACC on the dentin-bonding abilities of a self-adhesive resin cement and a dual-cure resin cement used with a primer. Unpolymerized MDPB showed strong antibacterial activity against 7 oral bacteria. ACC produced inhibition zones against all bacterial species similar to CPS. For ACC and CPS, the MIC value for S. mutans was identical, and the MBC was similar with only a 1-step dilution difference (1:2). Treatment of infected dentin with ACC resulted in significantly greater bactericidal effects than CPS ( P < 0.05, analysis of variance and Tukey’s honest significant difference test). ACC showed no negative influences on the bonding abilities to dentin for both resin cements, while CPS reduced the bond strength of the self-adhesive resin cement ( P < 0.05). This study clarified that the experimental cavity disinfectant containing 5% MDPB is more effective in vitro than the commercially available chlorhexidine solution to eradicate bacteria in dentin, without causing any adverse influences on the bonding abilities of resinous luting cements.

The Effect of Aging and Surface treatments on Micro-shear Bond Strength of Resin Nano-Ceramic Material Using Two Resin Cements

2020 ◽  
Author(s):  
Ayman Mohammed Said
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Resin Cement ◽  
Acid Etching ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Mean Values ◽  
Adhesive Resin Cement

Purpose: To evaluate the effect of aging and different surface treatments on micro-shear bond strength of two resin cements to resin nano-ceramic composite blocks using an in-vitro study. Materials and methods: Blocks of resin nano-ceramic (Lava Ultimate, 3M, St Paul, Minnesota, USA) were used to prepare eight plates having the following dimensions: (14mm × 12mm × 2mm). After plates preparation they were assigned to two main groups according to the surface treatment applied, either hydrofluoric acid etching and silane or sandblasting and silane. Scanning electron microscope (SEM) was used to analyze the surface topography of the Lava-Ultimate plates before and after application of surface treatments. Two resin cements were used; dual cured adhesive resin cement (Bifix QM, VOCO, Cuxhafen, Germany) and dual cured self-adhesive resin cement (Bifix SE, VOCO, Cuxhafen, Germany) to create a five resin micro-cylinders received on each lava ultimate plate. Ten specimens from each subgroup were tested after 24 hours and the other ten specimens were tested after aging in saline for 6 months. Micro-shear bond strength test was applied until failure. . Multi-factorial ANOVA test and One-way ANOVA followed by pair-wise Tukey’s post-hoc tests were used to analyze the data. Results: Both resin cements showed statistically significant decrease on bond strength after aging. Before aging, both surface treatments with adhesive resin cement showed statistically significant higher micro-shear bond strength mean values than with self-adhesive resin cement. After aging sandblasting showed a statistically significant higher micro-shear bond strength mean values with adhesive resin cement, while hydrofluoric acid etching revealed a statistically non-significant higher values with adhesive resin cement than self-adhesive resin cement. Conclusion: For both surface treatments and resin cements aging had a detrimental effect on micro- shear bond strength.

Effect of Silanization on Microtensile Bond Strength of Different Resin Cements to a Lithium Disilicate Glass Ceramic

2016 ◽  
Vol 17 (2) ◽  
pp. 149-153 ◽  
Author(s):  
Cristina Parise Gré ◽  
Renan C de Ré Silveira ◽  
Shizuma Shibata ◽  
Carlo TR Lago ◽  
Luiz CC Vieira
Keyword(s):  
Bond Strength ◽  
Glass Ceramic ◽  
Hydrofluoric Acid ◽  
Lithium Disilicate ◽  
Resin Cement ◽  
Microtensile Bond Strength ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Silane Coupling ◽  
Adhesive Resin Cement

ABSTRACT Aim This study evaluated the influence of a silane-coupling agent on the bond strength of a self-adhesive cement and a conventional resin cement to a lithium disilicate glass ceramic. Materials and methods A total of eight ceramic blocks were fabricated and divided into four groups (n = 2). In groups 1 and 3, ceramic surfaces were etched with hydrofluoric acid 10% for 20 seconds, rinsed for 30 seconds, and air-dried. One layer of a silane agent was applied onto all ceramic specimens and air-dried for 30 seconds. In groups 2 and 4, ceramic surfaces were etched with hydrofluoric acid, rinsed, and air-dried without application of the silane-coupling agent. The ceramic blocks were bonded to a block of composite with a self-adhesive resin cement or with a conventional resin cement, according to the manufacturer's instructions. After 24 hours in distilled water at 37°C, the specimens were sectioned perpendicular to the bonding interface area to obtain beams with a bonding area of 0.8 mm2 and submitted to a microtensile bond strength test at a crosshead speed of 0.5 mm/min. Data were statistically analyzed with one-way analysis of variance and the Games–Howell post hoc test (p = 0.05). Fractured specimens were examined under optical microscopy at 40× magnification. Results Silanization resulted in higher microtensile bond strength compared to groups without silane. No significant differences were found between the conventional resin cement and the self-adhesive resin cement with silane agent (p = 0.983), and without silane agent (p = 0.877). Conclusion Silanization appears to be crucial for resin bonding to a lithium disilicate-based ceramic, regardless of the resin cement used. The self-adhesive resin cement performed as well as the conventional resin cement. Clinical significance Applying one layer of a silane-coupling agent after etching the ceramic surface with hydrofluoric acid 10% enhanced the bond strength between resin cements and a glass ceramic. How to cite this article Gré CP, de Ré Silveira RC, Shibata S, Lago CTR, Vieira LCC. Effect of Silanization on Microtensile Bond Strength of Different Resin Cements to a Lithium Disilicate Glass Ceramic. J Contemp Dent Pract 2016;17(2):149-153.

scholarly journals COMPARATIVE EVALUATION OF PUSH-OUT BOND STRENGTH AND FAILURE MODES OF FIBER POST CEMENTED WITH DIFFERENT ADHESIVE RESIN CEMENTS: AN IN-VITRO STUDY

2020 ◽  
pp. 1-3
Author(s):  
Sonali Bansod ◽  
Ashwini Gaikwad ◽  
Abhijit Jadhav
Keyword(s):  
Bond Strength ◽  
Resin Cement ◽  
Fiber Post ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Significant Difference ◽  
Group 3 ◽  
Adhesive Resin Cement ◽  
Group 2 ◽  
Push Out

Aim: To compare the push-out bond strength and modes of failure of fiber post cemented with different adhesive resin cements. Materials and Method: Forty five single rooted teeth were randomly divided into three groups as, group 1- Fluorocore 2+, group 2- Rely-X U200 and group 3-G-Cem, according to the adhesive resin cement used. The roots were subjected to chemo-mechanical preparation and cemented with adhesive resin cement. The teeth were sectioned into slices of the different root thirds and tested for bond strength (push out). Results were analysed using Chi square, Mann Whitney U and Kruskal Wallis test was used to find the significance of study parameters between three or more groups, with p = 0.05 for statistical significance. Result: Push out bond strength of Fluorocore 2+ is significantly higher at coronal level than apical level. No significant difference observed between coronal, middle and apical levels in group 2 and in group 3. Conclusion: Fluorocore 2+ adhesive resin cement is best to use for luting the fibre post. Fluorocore 2+ forms better bonding with post as well as dentin proving its better efficiency clinically.

scholarly journals Influence of Surface Treatment and Resin Cements on the Bond Strength between the Y-TZP Zirconia and Composite Resin Interface

2019 ◽  
Vol 21 (5) ◽  
pp. 477-482
Author(s):  
Lucas Campagnaro Maciel ◽  
Amanda Pádua Proeza ◽  
Hélyda Coelho Guimarães Balbino ◽  
Marcela Moráo Corteletti ◽  
Ricardo Huver De Jesus ◽  
...  
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Composite Resin ◽  
Surface Treatments ◽  
Resin Cement ◽  
The Self ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Significant Difference ◽  
Adhesive Resin Cement

AbstractThe evolution of dental materials and the improvement of ceramic systems stimulated the increased use of Y-TZP zirconia-based ceramics. Despite the excellent mechanical performance, this material has low adhesion potential. The objective of this work was to evaluate the surface treatments and resin cements influence on bond strength between Y-TZP zirconia and composite resin interface. A total of 60 blocks of Y-TZP zirconia (3x8x8mm) were prepared and divided into 3 groups according to the surface treatments: (C) control - extra fine diamond bur, (J) sandblasting with Al2O3 and (JP) sandblasting with Al2O3 + ceramic primer. Each group was subdivided into two groups according to type of resin cement used for cementing composite resin discs (2mm thick x 5mm diameter): self-adhesive and conventional (n=10). The samples were stored in distilled water for 24 hours at 37±1°C in a incubator and subsequently submitted to the shear bond test to determine the bond strength (RU). There was no significant difference in RU among the  surface treatments when using conventional resin cement. For the self-adhesive resin cement, Al2O3 blasting and Al2O3 + primer blasting increased the RU but did not present significant differences between them (p<0.05). Comparing the cements, it was observed that regardless of the surface treatment, the highest values were for the self-adhesive resin cement (p<0.05). Application of the primer after blasting with Al2O3 did not increase RU. Keywords: Dental Prosthesis. Ceramics. Dental cements. Shear Strength.  ResumoA evolução dos materiais odontológicos e o aprimoramento dos sistemas cerâmicos impulsionaram o aumento da utilização da cerâmica a base de zircônia Y-TZP. Apesar do excelente desempenho mecânico, este material apresenta baixo potencial de adesão. O objetivo deste trabalho foi avaliar a influência dos tratamentos de superfícies e dos cimentos resinosos na resistência de união entre a interface zircônia Y-TZP e resina composta. Foram confeccionados 60 blocos de zircônia Y-TZP (3x8x8 mm) e divididos em 03 grupos de acordo com os tratamentos de superfícies que receberam: (C) controle - ponta diamantada extrafina, (J) jateamento com Al2O3 e (JP) jateamento com Al2O3 + primer cerâmico. Cada grupo foi subdividido em dois novos grupos de acordo com tipo de cimento resinoso utilizado para cimentação de discos de resina composta (2mm de espessura x 5mm de diâmetro): autoadesivo e resinoso convencional (n=10). As amostras foram armazenadas em água destilada por 24 horas a 37±1°C em estufa e posteriormente submetidas ao teste de cisalhamento para averiguar a resistência de união (RU). Não houve diferença significativa na RU entre os tratamentos de superfície quando utilizado o cimento resinoso convencional. Para o cimento resinoso autoadesivo o jateamento com Al2O3 e o jateamento de Al2O3 + primer aumentaram a RU porém não apresentaram diferenças significativas entre si (p<0,05). Comparando os cimentos observou-se que, independente do tratamento de superfície, os maiores valores foram para o cimento resinoso autoadesivo (p<0,05). A aplicação do primer após o jateamento com Al2O3 não proporcionou aumento da RU. Palavras-chave: Prótese Dentária. Cerâmica. Cimentos Dentários. Resistência ao Cisalhamento.

scholarly journals Shear Bond Strength of MDP-Containing Self-Adhesive Resin Cement and Y-TZP Ceramics: Effect of Phosphate Monomer-Containing Primers

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Jin-Soo Ahn ◽  
Young-Ah Yi ◽  
Yoon Lee ◽  
Deog-Gyu Seo
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Control Group ◽  
Air Abrasion ◽  
Adhesive Resin ◽  
Multiple Comparison Test ◽  
Ceramic Surfaces ◽  
Adhesive Resin Cement

Purpose. This study was conducted to evaluate the effects of different phosphate monomer-containing primers on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramics and MDP-containing self-adhesive resin cement.Materials and Methods. Y-TZP ceramic surfaces were ground flat with #600-grit SiC paper and divided into six groups (n=10). They were treated as follows: untreated (control), Metal/Zirconia Primer, Z-PRIME Plus, air abrasion, Metal/Zirconia Primer with air abrasion, and Z-PRIME Plus with air abrasion. MDP-containing self-adhesive resin cement was applied to the surface-treated Y-TZP specimens. After thermocycling, a shear bond strength test was performed. The surfaces of the Y-TZP specimens were analyzed under a scanning electron microscope. The bond strength values were statistically analyzed using one-way analysis of variance and the Student–Newman–Keuls multiple comparison test (P<0.05).Results. The Z-PRIME Plus treatment combined with air abrasion produced the highest bond strength, followed by Z-PRIME Plus application, Metal/Zirconia Primer combined with air abrasion, air abrasion alone, and, lastly, Metal/Zirconia Primer application. The control group yielded the lowest results (P<0.05).Conclusion. The application of MDP-containing primer resulted in increased bond strength between Y-TZP ceramics and MDP-containing self-adhesive resin cements.

scholarly journals Changes in Bond Strength and Topography for Y-TZP Etched with Hydrofluoric Acid Depending on Concentration and Temperature Conditions

Medicina ◽  
2020 ◽  
Vol 56 (11) ◽  
pp. 568
Author(s):  
Hyo-Eun Kim ◽  
Myung-Jin Lim ◽  
Mi-Kyung Yu ◽  
Kwang-Won Lee
Keyword(s):  
Surface Roughness ◽  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Room Temperature ◽  
High Surface ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Grain Structure ◽  
Temperature Conditions ◽  
Significant Difference

Background and objectives: This study aimed to investigate the change in bond strength between resin cement and tetragonal zirconia polycrystalline stabilized with 3 to 8 mol% yttrium oxide (Y-TZP) and observe the topographical change of the Y-TZP surface when etched with hydrofluoric acid (HF) solution under different concentration and temperature conditions. Materials and Methods: Non-etched sintered Y-TZP specimens under two different temperature conditions (room temperature and 70–80 °C, respectively), were used as a control, while experimental groups were etched with 5%, 10%, 20%, and 40% HF solutions for 10 min. After zirconia primer and MDP-containing resin cement were applied to the Y-TZP surface, the shear bond strength (SBS) of each experimental group was measured. Results: Under room temperature conditions, the highest SBS value was measured in the 40% HF etching group, representing a significant deviation from the other groups (p < 0.05). In the 70–80 °C tests, the 40% HF etching group also had the highest SBS value, but there was no significant difference when compared to the 20% HF etching group (p > 0.05). From SEM and AFM observations, the HF solution increasingly dissolved the Y-TZP surface grain structure as the concentration and application temperature rose, resulting in high surface roughness and irregularities. Conclusions: Pretreating with either 20% HF solution at 70–80 °C or 40% HF solution at room temperature and 70–80 °C effectively acid etched the Y-TZP surface, resulting in more surface roughness and irregularities. Accounting for the concentration and temperature conditions of the HF solution, using 40% HF solution at room temperature will result in improvements in adhesion between resin cement and Y-TZP.

Sign in / Sign up

Export Citation Format

Share Document