Ceramic Primer Heat-Treatment Effect on Resin Cement/Y-TZP Bond Strength

2012 ◽  
Vol 37 (6) ◽  
pp. 634-640 ◽  
Author(s):  
LH Silva ◽  
AKF Costa ◽  
JRC Queiroz ◽  
MA Bottino ◽  
LF Valandro
Keyword(s):  
Heat Treatment ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Dihydrogen Phosphate ◽  
Gravimetric Analysis ◽  
Ceramic Surface ◽  
Aging Condition ◽  
Experimental Group

SUMMARY The purpose of this study was to evaluate the effect of different heat-treatment strategies for a ceramic primer on the shear bond strength of a 10-methacryloyloxydecyl-dihydrogen-phosphate (MDP)-based resin cement to a yttrium-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic. Specimens measuring 4.5 × 3.5 × 4.5 mm3 were produced from Y-TZP presintered cubes and embedded in polymethyl methacrylate (PMMA). Following finishing, the specimens were cleaned using an ultrasound device and distilled water and randomly divided into 10 experimental groups (n=14) according to the heat treatment of the ceramic primer and aging condition. The strategies used for the experimental groups were: GC (control), without primer; G20, primer application at ambient temperature (20°C); G45, primer application + heat treatment at 45°C; G79, primer application + heat treatment at 79°C; and G100, primer application + heat treatment at 100°C. The specimens from the aging groups were submitted to thermal cycling (6000 cycles, 5°C/55°C, 30 seconds per bath) after 24 hours. A cylinder of MDP-based resin cement (2.4 mm in diameter) was constructed on the ceramic surface of the specimens of each experimental group and stored for 24 hours at 37°C. The specimens were submitted to a shear bond strength test (n=14). Thermal gravimetric analysis was performed on the ceramic primer. The data obtained were statistically analyzed by two-way analysis of variance and the Tukey test (α=0.05). The experimental group G79 without aging (7.23 ± 2.87 MPa) presented a significantly higher mean than the other experimental groups without aging (GC: 2.81 ± 1.5 MPa; G20: 3.38 ± 2.21 MPa; G100: 3.96 ± 1.57 MPa), showing no difference from G45 only (G45: 6 ± 3.63 MPa). All specimens of the aging groups debonded during thermocycling and were considered to present zero bond strength for the statistical analyses. In conclusion, heat treatment of the metal/zirconia primer improved bond strength under the initial condition but did not promote stable bonding under the aging condition.

Bonding Polycrystalline Zirconia With 10-MDP–containing Adhesives

2017 ◽  
Vol 42 (3) ◽  
pp. 335-341 ◽  
Author(s):  
AE Llerena-Icochea ◽  
RM Costa ◽  
AFS Borges ◽  
JFS Bombonatti ◽  
AY Furuse
Keyword(s):  
Bisphenol A ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Dihydrogen Phosphate ◽  
Single Bond ◽  
Glycol Dimethacrylate ◽  
Significant Difference

SUMMARY Objective: The objective of this study was to evaluate the influence of adhesives with different 10-MDP concentrations on the shear bond strength of a resin cement to zirconia. Methods and Materials: Six experimental adhesives were prepared with the following composition: camphorquinone, 1,2-diaminobenzene, butylhydroxytoluene, diphenyliodonium hexafluorophosphate, 2-hydroxyethyl methacrylate triethylene glycol dimethacrylate, ethoxylated bisphenol A glycol dimethacrylate, urethane dimethacrylate, bisphenol A diglycidyl methacrylate, and ethanol. The 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) monomer was added at 0wt%, 3wt%, 6wt%, 9wt%, 12wt%, or 15wt%. Three commercially available adhesives were evaluated: Single Bond Universal, Single Bond 2, and Signum Zirconia Bond. Resin cement cylinders made with RelyX Ultimate were bonded to yttria-stabilized tetragonal zirconia polycrystal with one of the evaluated adhesives and were subjected to the shear bond strength evaluation. Failure modes were analyzed with a stereoscopic loupe. Statistical analyses were performed with one-way analysis of variance and the Tukey's Honestly Significant Difference test (α=0.05). Pearson's was used to correlate the percentage of 10-MDP in the experimental adhesives and shear bond strength. Results: There were significant differences between adhesives (p<0.00001). The highest shear bond strength values were obtained with the Signum Zirconia Bond and Single Bond Universal. Single Bond 2 showed the lowest values. There were no differences between experimental adhesives. All groups showed adhesives failures. A nonlinear correlation was found between bond strength and percentage of 10-MDP in experimental adhesives (r=0.872). Conclusions: The commercially available adhesives indicated for bonding to zirconia showed the highest bonding values.

scholarly journals Effect of MDP-Based Primers on the Luting Agent Bond to Y-TZP Ceramic and to Dentin

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Sheila Butler ◽  
Bernie Linke ◽  
Ysidora Torrealba
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Silica Particles ◽  
Resin Cement ◽  
Ceramic Surface ◽  
Universal Adhesive ◽  
Luting Agent ◽  
Post Hoc ◽  
Application Protocols

Purpose. The aim of this study was to evaluate the influence of multimode MDP-based primers and different application protocols on the bond strength of a representative resin cement to an yttrium stabilized tetragonal zirconia (Y-TZP) ceramic.Materials and Methods. The occlusal dentin from 60 human molars was exposed. The teeth and zirconia cylinders (N = 60) (3 mm of diameter; 4 mm of height) were divided into six groups (n = 10) according to the ceramic surface conditioning: (1) air abraded with SiO2particles; (2) Z-Prime Plus; (3) air abraded with SiO2particles + Z-Prime Plus; (4) air abraded with SiO2particles + All-Bond Universal; (5) air abraded with SiO2particles + ScotchBond Universal Adhesive; and (6) untreated zirconia. The luting agent (Duo-Link cement) was applied on the treated dentin surface. Specimens were stored in water (37°C, 24 h) and tested in shear bond strength. Data were statistically analyzed using 2-way ANOVA and Post hoc Tukey tests (α= 0.05).Results. Significant effects of ceramic conditioning were found (p<0.0001). The specimens sandblasted with silica particles followed by the application of Z-Prime Plus or All-Bond Universal presented greater bond strength values. For the untreated zirconia, several specimens failed prematurely prior to testing.Conclusions. Sandblasting with silica particles combined with Z-Prime Plus increased the bond strength.

scholarly journals Novel Femto Laser Patterning of High Translucent Zirconia as an Alternative to Conventional Particle Abrasion

2021 ◽  
Vol 9 (2) ◽  
pp. 20
Author(s):  
Emmanouil-George C. Tzanakakis ◽  
Anastasia Beketova ◽  
Lambrini Papadopoulou ◽  
Eleana Kontonasaki ◽  
Ioannis G. Tzoutzas
Keyword(s):  
Femtosecond Laser ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Tetragonal Zirconia ◽  
Treated Group ◽  
Glass Beads ◽  
Surface Treatments ◽  
Dihydrogen Phosphate ◽  
Promising Alternative

Background: currently applied surface treatments for zirconia bonding may create undesired microcracks and surface flaws. The aim of the present study was to evaluate the efficacy of alternative surface treatments on the shear bond strength of high translucency zirconia to 10-Methacryloyloxydecyl dihydrogen phosphate (MDP)-containing resin-based cement. Methods: fifty disk-shaped specimens (10 mm × 5 mm) were fabricated from a commercial yttria-stabilized zirconia with 5 mole% yttrium oxide tetragonal zirconia polycrystal (5Y-TZP), and underwent air-abrasion with alumina particles (50 μm-AL50 and 90 μm-AL90), glass beads (GB 10–60 μm), and ablation with femtosecond laser (FEMTO). Shear bond strength was evaluated with a universal testing machine under a crosshead speed of 0.5 mm/min until fracture. Fracture type was evaluated with an optical stereomicroscope. Differences among groups were evaluated by one-way ANOVA and Bonferroni pairwise comparison tests (p < 0.05). Results: the highest shear bond strength values were presented by the laser treated group (23.97 ± 3.7 MPa). No statistically significant differences were found among the Cl, Al50, Al90 and FEMTO groups. The lowest mean value was presented by the glass-beads treated group (11.93 ± 2.88 MPa) which was significantly lower compared to all other groups (p < 0.001). Conclusions: under the limitations of this in vitro study, femtosecond laser treatment of High-translucent monolithic zirconia (HTZ) ceramics is a promising alternative method for the mechanical retention of resin cements.

The Effect of Sandblasting and Different Primers on Shear Bond Strength Between Yttria-tetragonal Zirconia Polycrystal Ceramic and a Self-adhesive Resin Cement

2015 ◽  
Vol 40 (1) ◽  
pp. 63-71 ◽  
Author(s):  
Y-A Yi ◽  
J-S Ahn ◽  
Y-J Park ◽  
S-H Jun ◽  
I-B Lee ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Xrd Analysis ◽  
Resin Cement ◽  
Air Abrasion ◽  
Adhesive Resin ◽  
Multiple Comparison Test ◽  
Adhesive Resin Cement ◽  
Tetragonal Zirconia Polycrystal

SUMMARY Purpose To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. Methods and Materials Y-TZP ceramic surfaces were ground flat with 600-grit silicon carbide paper and then divided into seven groups of 10 and treated as follows: untreated (control), Monobond Plus, Z-PRIME Plus, ESPE Sil with CoJet, air-abrasion, Monobond Plus with air-abrasion, and Z-PRIME Plus with air-abrasion. Self-adhesive resin cement was placed onto the treated Y-TZP specimens for each group. All specimens were thermocycled and subjected to a shear bond strength test. Scanning electron microscope images of the fractured areas and x-ray diffraction (XRD) analysis of the surface-treated Y-TZP specimens were performed. Data were statistically analyzed using one-way analysis of variance and the Student-Newman-Keuls multiple comparison test (p&lt;0.05). Results The Z-PRIME Plus treatment in combination with air-abrasion produced the highest bond strength (16.50±2.26 MPa), followed by air-abrasion (10.56±3.32 MPa), and then Monobond Plus combined with air-abrasion (8.93±3.13 MPa), ESPE Sil after CoJet application (8.54±3.98 MPa), and the Z-PRIME Plus group (8.27±2.79 MPa). The control (3.91±0.72 MPa) and Monobond Plus (4.86±1.77 MPa) groups indicated the lowest results (p&lt;0.05). The XRD results showed the peaks of the monoclinic phase for the air-abrasion and CoJet treatment groups compared with the Y-TZP control. Conclusion Z-PRIME Plus primer application after air-abrasion presented the best results for improving the bond strength between Y-TZP ceramic and self-adhesive resin cement.

scholarly journals The effect of surface treatment and thermocycling on the shear bond strength of porcelain laminate veneering material cemented with different luting cements

2019 ◽  
Vol 18 ◽  
pp. e191581
Author(s):  
Fawaz Alqahtani ◽  
Mohammed Alkhurays
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Resin Cement ◽  
Ceramic Surface ◽  
Resin Cements ◽  
Significant Difference ◽  
Acid Etch

Aim: The study aimed to evaluate and compare the effect of different surface treatment and thermocycling on the shear bond strength (SBS) of different dual-/light-cure cements bonding porcelain laminate veneers (PLV). Methods: One hundred and twenty A2 shade lithium disilicate discs were divided into three groups based on the resin cement used and on the pretreatment received and then divided into two subgroups: thermocycling and control. The surface treatment were either micro-etched with aluminium trioxide and 10% hydrofluoric acid or etched with 10% hydrofluoric acid only before cementation. Three dual-cure (Variolink Esthetic (I), RelyX Ultimate (II), and RelyX Unicem (III)) and three light-cure (Variolink Veneer (IV), Variolink Esthetic (V), RelyX Veneer (VI)) resin cements were used for cementation. The SBS of the samples was evaluated and analysed using three -way ANOVA with statistical significant set at α=0.05. Results: For all resin cements tested with different surface treatments, there was a statistically significant difference within resin cements per surface treatment (p<0.05). The shear bond strength in the micro-etch group was significant higher than the acid-etch group (p<0.05) There was statistically significant interaction observed between the surface treatment and thermocycling (p<0.05) as well as the cement and thermocycling(p<0.05). It was observed that the reduction in shear bond strength after thermocycling was more pronounced in the acid etch subgroup as compared to the microetch subgroup. However, the interaction between the three factors: surface treatments, thermocycling and resin cements did not demonstrate statistically significant differences between and within groups (p=0.087). Conclusions: Within the limitations of the present study, it acan be concluded that Dual cure resin cements showed a higher Shear bond strength as compared to light cure resin cements. Thermal cycling significantly decreased the shear bond strength for both ceramic surface treatments. After thermocycling, the specimens with 10% HF surface treatment showed lower shear bond strength values when compared to those treated by sandblasting with Al2O3 particles.

scholarly journals Shear bond strength of resin cement to an acid etched and a laser irradiated ceramic surface

2013 ◽  
Vol 5 (2) ◽  
pp. 98 ◽  
Author(s):  
Pinar Kursoglu ◽  
Pelin Fatma Karagoz Motro ◽  
Haktan Yurdaguven
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Cement ◽  
Ceramic Surface

scholarly journals Bonding of Y-TZP to Dentin: Effects of Y-TZP Surface Conditioning, Resin Cement Type, and Aging

2014 ◽  
Vol 39 (3) ◽  
pp. 291-300 ◽  
Author(s):  
MA Bottino ◽  
C Bergoli ◽  
EG Lima ◽  
SMS Marocho ◽  
RO Souza ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Acrylic Resin ◽  
Surface Treatments ◽  
Resin Cement ◽  
Occlusal Plane ◽  
Resin Cements ◽  
And Storage ◽  
Tetragonal Zirconia Polycrystal

SUMMARY Purpose To evaluate the effects of two surface treatments, aging, and two resin cements on shear bond strength between dentin and yttrium-stabilized tetragonal zirconia polycrystal ceramic (Y-TZP). Materials and Methods Eighty human molars were embedded in acrylic resin and sectioned 3 mm below the occlusal plane. These teeth and 80 cylindrical Y-TZP specimens (height, 4 mm; diameter, 3.4 mm) were divided into eight groups (n=10) using the following factors: Y-TZP surface treatment (Vi: low-fusing porcelain [vitrification] + hydrofluoric acid etching + silanization or Si: tribochemical silicatization); cementation strategies (PF: Panavia or CC: Clearfil); and storage (nonaging or aging). Bonding surfaces of 40 Y-TZP specimens received Vi treatment, and the rest received Si treatment. Half of the ceramic-tooth assemblies were cemented with Panavia, the rest with Clearfil. Shear tests were executed using 0.4-mm–thick wire at 0.5 mm/min. Data were analyzed by three-way analysis of variance and Tukey test (α=0.05). Fractures were analyzed. Results Y-TZP surface treatments did not affect bond strength (p=0.762, Vi = Si), while resin cements (p&lt;0.001, Panavia &gt; Clearfil) and aging (p=0.006, nonaging &gt; aging) showed a significant effect. Most failures were in adhesive at dentin-cement interfaces; no failure occurred between zirconia and cement. Conclusion When Y-TZP ceramic is bonded to dentin, the weakest interface is that between dentin and resin cement. The resin cement/Y-TZP interface was less susceptible to failures, owing to Y-TZP surface treatments.

scholarly journals Shear Bond Strength of MDP-Containing Self-Adhesive Resin Cement and Y-TZP Ceramics: Effect of Phosphate Monomer-Containing Primers

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Jin-Soo Ahn ◽  
Young-Ah Yi ◽  
Yoon Lee ◽  
Deog-Gyu Seo
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Tetragonal Zirconia ◽  
Resin Cement ◽  
Control Group ◽  
Air Abrasion ◽  
Adhesive Resin ◽  
Multiple Comparison Test ◽  
Ceramic Surfaces ◽  
Adhesive Resin Cement

Purpose. This study was conducted to evaluate the effects of different phosphate monomer-containing primers on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramics and MDP-containing self-adhesive resin cement.Materials and Methods. Y-TZP ceramic surfaces were ground flat with #600-grit SiC paper and divided into six groups (n=10). They were treated as follows: untreated (control), Metal/Zirconia Primer, Z-PRIME Plus, air abrasion, Metal/Zirconia Primer with air abrasion, and Z-PRIME Plus with air abrasion. MDP-containing self-adhesive resin cement was applied to the surface-treated Y-TZP specimens. After thermocycling, a shear bond strength test was performed. The surfaces of the Y-TZP specimens were analyzed under a scanning electron microscope. The bond strength values were statistically analyzed using one-way analysis of variance and the Student–Newman–Keuls multiple comparison test (P<0.05).Results. The Z-PRIME Plus treatment combined with air abrasion produced the highest bond strength, followed by Z-PRIME Plus application, Metal/Zirconia Primer combined with air abrasion, air abrasion alone, and, lastly, Metal/Zirconia Primer application. The control group yielded the lowest results (P<0.05).Conclusion. The application of MDP-containing primer resulted in increased bond strength between Y-TZP ceramics and MDP-containing self-adhesive resin cements.

Sign in / Sign up

Export Citation Format

Share Document