The Effect of Curing Units and Staining Solutions on the Color Stability of Resin Composites

10.2341/07-3 ◽  
2007 ◽  
Vol 32 (6) ◽  
pp. 616-622 ◽  
Author(s):  
A. R. Yazici ◽  
Ç Çelik ◽  
B. Dayangaç ◽  
G. Özgünaltay
Keyword(s):  
Clinical Relevance ◽  
Immersion Time ◽  
Resin Composite ◽  
Color Stability ◽  
Time Dependent ◽  
Resin Composites ◽  
Color Changes ◽  
Light Curing

Clinical Relevance The color stability of resin composites did not vary based on the type of light curing unit. The effect of staining solutions on color changes in resin composites was resin composite and immersion time-dependent.

Effect of Pre-heating Resin Composite on Restoration Microleakage

10.2341/07-41 ◽  
2008 ◽  
Vol 33 (1) ◽  
pp. 72-78 ◽  
Author(s):  
W. C. Wagner ◽  
M. N. Aksu ◽  
A. L. Neme ◽  
J. B. Linger ◽  
F. E. Pink ◽  
...  
Keyword(s):  
Clinical Relevance ◽  
Resin Composite ◽  
Resin Composites ◽  
Tooth Structure ◽  
Positive Effects ◽  
Light Curing

Clinical Relevance The results of this study indicate that preheating composites can improve adaptation of resin composites to tooth structure. This technique significantly reduced microleakage. However, delaying light curing of the preheated composite after placement appears to be counterproductive and diminishes the positive effects from the preheating treatment. Flowable liner was less effective than preheating the composite in reducing microleakage.

scholarly journals Effects of Commonly Consumed Beverages on Surface Roughness and Color Stability of the Nano, Microhybrid and Hybrid Composite Resins: An in vitro Study

2013 ◽  
Vol 14 (4) ◽  
pp. 718-723 ◽  
Author(s):  
P Sarveshwar Reddy ◽  
KL Sunil Tejaswi ◽  
Suneeth Shetty ◽  
BM Annapoorna ◽  
Sudarshan C Pujari ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Hybrid Composite ◽  
Color Change ◽  
Resin Composite ◽  
Color Stability ◽  
Composite Resins ◽  
Resin Composites ◽  
Hybrid Resin ◽  
Color Changes

ABSTRACT Background Consumption of certain beverages may affect the esthetic and physical properties of the resin composite, thereby undermining the quality of restorations. Aim To analyze the effect of three beverages (cola, coffee, tea) on color stability and surface roughness of three different types of resin composites at various time intervals in vitro. Materials and methods Nano, microhybrid and hybrid resin composites were used. Each material was randomly divided into four equal subgroups of 10 samples each according to the beverages used (cola, coffee, tea, distilled water). The samples were immersed in each beverage for 1, 15 and 30 days. Surface roughness and color changes measurements were noted at the baseline—the first, fifteenth and thirteenth day. Results It was found that nanoresin composite followed by microhybrid and hybrid showed least surface roughness and color change. The Coke beverage subgroup showed more surface roughness and the subgroup coffee has shown more color changes with respect to other subgroups. Conclusion All specimens showed discoloration after completion of the test period which was visually perceptible and clinically unacceptable. At the end of 30th day, among the materials, nanofilled composite resin showed comparatively less surface roughness and color change than microhybrid and hybrid composite resins. How to cite this article Reddy PS, Tejaswi KLS, Shetty S, Annapoorna BM, Pujari SC, Thippeswamy HM. Effects of Commonly Consumed Beverages on Surface Roughness and Color Stability of the Nano, Microhybrid and Hybrid Composite Resins: An in vitro Study. J Contemp Dent Pract 2013;14(4): 718-723.

Change of Color and Translucency by Light Curing in Resin Composites

2006 ◽  
Vol 31 (5) ◽  
pp. 598-603 ◽  
Author(s):  
S. K. Sidhu ◽  
T. Ikeda ◽  
Y. Omata ◽  
M. Fujita ◽  
H. Sano
Keyword(s):  
Composite Materials ◽  
Clinical Relevance ◽  
Color Change ◽  
Resin Composite ◽  
Resin Composites ◽  
Light Curing ◽  
Shade Matching

Clinical Relevance For the precise shade matching of resin composite materials, clinicians should always be aware of the color change caused by light curing.

Color Stability Behavior of Methacrylate-based Resin Composites Polymerized with Light-emitting Diodes and Quartz-Tungsten-Halogen

2015 ◽  
Vol 40 (3) ◽  
pp. 271-281 ◽  
Author(s):  
C Sabatini
Keyword(s):  
Light Emitting Diodes ◽  
Color Change ◽  
Resin Composite ◽  
Filler Particle ◽  
Color Stability ◽  
Resin Composites ◽  
Light Emitting ◽  
Color Changes ◽  
Quartz Tungsten Halogen ◽  
Before And After

SUMMARY Despite significant developments in improving the optical properties of resin composite materials, their color stability remains a challenge. This study aimed to evaluate the shade stability of light-polymerized, methacrylate-based resin composites with different filler particle composition (microfill, minifill, nanohybrids, and microhybrids) polymerized with quartz-tungsten-halogen (QTH) and light-emitting diodes (LED). Methods and Materials Composite discs were fabricated from Tetric EvoCeram, Premise, Artiste, and Beautifil II (nanohybrids); Filtek Supreme Plus and Vit-l-escence (microhybrids); Heliomolar (microfill); and Estelite Sigma Quick (minifill) using a Teflon mold. The specimens were irradiated either with QTH (Elipar 2500; 600 mW/cm2) for 40 seconds or with LED (Bluephase G2; 1200 mW/cm2) for 20 seconds. Color parameters were measured with a colorimeter before and after polymerization and at 24 hours, one week, one month, and three months. Color change was calculated among the different storage periods. Results There was a significant effect of the composite, time, and their interaction (p<0.001) but no effect of the polymerization unit on the color stability. Color changes immediately after polymerization and at 24 hours (4.22 and 3.88 for LED; and 4.08 and 3.82 for QTH) were not significantly different from each other but were both significantly higher than changes after one week (0.96 and 0.78), one month (1.12 and 1.02), and three months (1.27 and 1.11) for LED and QTH, respectively (p<0.001). Conclusions Color changes were observed for all the materials that were dependent on the type of composite but not on the polymerization unit. These color shifts took place primarily immediately after polymerization and after 24 hours and were additive in nature.

scholarly journals Color Stability and Gloss of Esthetic Restorative Materials after Chemical Challenges

2019 ◽  
Vol 30 (1) ◽  
pp. 52-57 ◽  
Author(s):  
Eduardo Haruki Ozera ◽  
Fernanda Miori Pascon ◽  
Américo Bortolazzo Correr ◽  
Regina Maria Puppin-Rontani ◽  
Aline Rogéria de Castilho ◽  
...  
Keyword(s):  
Color Change ◽  
Artificial Saliva ◽  
Color Stability ◽  
Initial Surface ◽  
Resin Composites ◽  
Cranberry Juice ◽  
Color Changes ◽  
Restorative Materials ◽  
Post Hoc ◽  
Acidic Beverages

Abstract This study evaluated gloss and color changes of esthetic restorative materials subjected to different acidic beverages. Specimens of resin composites (Z350XT (Z350), IPS Empress Direct (ED), Charisma Diamond (CD)) were prepared and the initial surface gloss and color (ΔE) were measured (n=10). Then, the specimens were immersed in 4 mL of each of the different beverages (cranberry juice; Coca-Cola; coffee or artificial saliva) during 15 min, 3x/day for 14 days and new gloss and color readings were obtained. Color change was evaluated with the ΔE formula and gloss change values were obtained by the formula: (final gloss - initial gloss). Data was submitted to two-way ANOVA followed by Tukey’s post hoc test (a=0.05). CD showed the lowest color change among resin composites. The highest ΔE values were obtained after immersion in coffee and cranberry juice. Coffee promoted the highest gloss change (worst gloss retention), followed by cranberry juice, Coca-cola and artificial saliva (p<0.05). The type of beverage significantly influenced the gloss of resin composites. Coca-cola reduced gloss of the three resin composites in a similar manner. Coffee affected the ED gloss more than that of Z350 and CD, while cranberry juice affected Z350 more than ED and CD. Saliva had a more pronounced effect on the gloss retention of CD than ED. The beverages used in this study influenced the optical surface properties of the composites studied.

The Effect of Energy Application Sequence on the Microtensile Bond Strength of Different C-factor Cavity Preparations

10.2341/06-30 ◽  
2007 ◽  
Vol 32 (2) ◽  
pp. 124-132 ◽  
Author(s):  
G. Maghaireh ◽  
M. R. Bouschlicher ◽  
F. Qian ◽  
S. R. Armstrong
Keyword(s):  
Bond Strength ◽  
Clinical Relevance ◽  
High Irradiance ◽  
Resin Composites ◽  
Microtensile Bond Strength ◽  
Light Curing ◽  
Bond Strengths ◽  
Energy Application

Clinical Relevance Light curing of resin composites in high C-factor cavity preparations using a high irradiance energy application sequence may lead to decreased bond strength. However, the high irradiance energy application sequence did not result in lower bond strengths in lower C-factor cavity preparations.

Does Layering Minimize Shrinkage Stresses in Composite Restorations?

2003 ◽  
Vol 82 (12) ◽  
pp. 967-971 ◽  
Author(s):  
R.H. Kuijs ◽  
W.M.M. Fennis ◽  
C.M. Kreulen ◽  
M. Barink ◽  
N. Verdonschot
Keyword(s):  
Dynamic Process ◽  
Apparent Viscosity ◽  
Poisson Ratio ◽  
Resin Composite ◽  
Time Dependent ◽  
Polymerization Process ◽  
Fe Model ◽  
Resin Composites ◽  
Polymerization Shrinkage ◽  
Simulated Time

Polymerization shrinkage of resin composites may impair restoration longevity. It is hypothesized that layering, rather than bulk, techniques result in less stress in the tooth-restoration complex. The aim of this study was to compare shrinkage stresses for different restorative techniques used for cusp-replacing restorations with direct resin composite. In a 3-D FE model, the dynamic process of shrinkage during polymerization was simulated. Time-dependent parameters (shrinkage, apparent viscosity, Young’s modulus, Poisson ratio, and resulting creep), which change during the polymerization process, were implemented. Six different restorative procedures were simulated: a chemically cured bulk technique, a light-cured bulk technique, and 4 light-cured layering techniques. When polymerization shrinkage is considered, a chemically cured composite shows the least resulting stress. The differences seen among various layering build-up techniques were smaller than expected. The results indicate that the stress-bearing locations are the interface and the cervical part of the remaining cusp.

scholarly journals Effect of Brushing Time and Dentifrice Abrasiveness on Color Change and Surface Roughness of Resin Composites

2015 ◽  
Vol 26 (5) ◽  
pp. 507-513 ◽  
Author(s):  
Lourenço de Moraes Rego Roselino ◽  
Michelle Alexandra Chinelatti ◽  
Carla Cecilia Alandia-Román ◽  
Fernanda de Carvalho Panzeri Pires-de-Souza
Keyword(s):  
Surface Roughness ◽  
Healthy Individual ◽  
Repeated Measures ◽  
Color Change ◽  
Resin Composite ◽  
Color Stability ◽  
Resin Composites ◽  
Repeated Measures Anova ◽  
Bonferroni Test ◽  
Initial Color

Abstract: Dentifrice abrasiveness and brushing time may increase color change (∆E) and surface roughness (∆Ra) of resin composites. This study aimed to evaluate the effect of mechanical brushing time of dentifrices with different abrasiveness on ∆E and ∆Ra of nanofilled (Z350, 3M ESPE) and nanohybrid (Tetric N-Ceram, Ivoclar Vivadent) resin composites. Sixteen specimens (12 mm diameter x 2 mm thick) were fabricated using a white Teflon matrix of each resin composite and a ceramic (IPS e.max Ceram, Ivoclar Vivadent), used as control. After initial color readouts on white backgrounds (Spectrophotometer PCB 6807, Byk Gardner), with D65 standard illuminant, and surface roughness (Rugosimeter Surfcorder SE 1700, Kosalab) with cut-off=0.8 mm and speed=0.25 mm/s, specimens were assigned (n=8) according to the abrasiveness of the dentifrices: RDA* 68 (Colgate) and RDA* 180 (Colgate Total Plus Whitening). Specimens were submitted to mechanical brushing (58,400 cycles) and after every 14,600 cycles (1 year of brushing by a healthy individual), new color and surface roughness readouts were taken. Color stability was calculated by CIEDE2000. Data were analyzed by 3-way repeated measures ANOVA and Bonferroni test (p<0.05), and demonstrated that the dentifrice abrasiveness (p=0.02) and brushing time (p<0.0001) affected the ∆E of nanofilled resin composite. There was no difference on surface roughness of materials (p=0.6752) or brushing time (p=0.7997). In conclusion, the longer the brushing time and dentifrice abrasiveness, the greater the color change of the nanofilled resin composite. The surface roughness was not influenced by dentifrice abrasiveness.

scholarly journals Effect of Staining Solutions on the Color Stability of Conventional and Bulk Fill Nanohybrid Resin Composites: A Spectrophotometric Analysis

2017 ◽  
Vol 2 (1) ◽  
pp. 1-5 ◽  
Author(s):  
Jayaprakash Thumu ◽  
Anirudh Kadiyala ◽  
Indira Priyadarshini Bollu ◽  
Srinidhi Vishnu Ballullaya ◽  
Srihari Devalla
Keyword(s):  
Color Change ◽  
Color Stability ◽  
Spectrophotometric Analysis ◽  
Resin Composites ◽  
Water Control ◽  
Group Iii ◽  
Color Changes ◽  
Group I ◽  
Immersion Period ◽  
Friedman's Test

ABSTRACT Aim This study is aimed to evaluate the effect of staining solutions on the color stability of bulk fill and conventional nanohybrid resin composites (RCs) when subjected to various immersion periods. Materials and methods A total of 120 cylindrical Teflon molds (4 × 4 mm) were obtained and divided into four groups of 30 each. Molds of groups I and II were filled with Tetric N Ceram Bulk Fill (Ivoclar Vivadent, Schaan, Liechtenstein) and Filtek Bulk Fill (3M ESPE, St. Paul, MN, USA). Molds of groups III and IV were filled with Tetric N Ceram (Ivoclar Vivadent) and Filtek Z250 XTE (3M ESPE) incremental fill RC. Photo-activation was performed and specimens were incubated. Spectrophotometer analysis was done according to Commission Internationale d'Eclairage Lab color scale. After taking the baseline measurements, 10 samples from each group were immersed in distilled water (control, subgroup a), tea (subgroup b), and coffee (subgroup c) respectively, for 1, 7, and 30 days. The color values of each specimen were remeasured and color change value (E*ab) was calculated after 1, 7, and 30 days. Data were analyzed by Friedman's test and Mann–Whitney U-test; p < 0.05 is considered to be statistically significant. Results Group III specimens showed perceptible color changes at 30-day immersion period in coffee and tea. In group I specimens, color changes were perceptible at 7- and 30-day immersion periods in coffee and only 30-day immersion period in tea. Groups II and IV specimens showed perceptible color changes after all immersion periods in coffee and after 30 days in tea. Conclusion It can be concluded that Tetric N Ceram has less color change than the other nanohybrid RCs investigated when immersed in coffee and tea after various immersion periods. How to cite this article Thumu J, Kadiyala A, Bollu IP, Ballullaya SV, Devalla S. Effect of Staining Solutions on the Color Stability of Conventional and Bulk Fill Nanohybrid Resin Composites: A Spectrophotometric Analysis. J Oper Dent Endod 2017;2(1):1-5.

Sign in / Sign up

Export Citation Format

Share Document