scholarly journals Non-Isothermal Simulation of Warm Circular Cup Deep Drawing Processing of an AZ31 Magnesium Alloy Sheet

2008 ◽  
Vol 49 (5) ◽  
pp. 1120-1123 ◽  
Author(s):  
Myeong Han Lee ◽  
Heon Young Kim ◽  
Heung Kyu Kim ◽  
Gi Deuck Kim ◽  
Soo Ik Oh
Keyword(s):  
Magnesium Alloy ◽  
Deep Drawing ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet

Numerical Simulation of Warm Deep Drawing of AZ31 Magnesium Alloy Sheet with Variable Blank Holder Force

2007 ◽  
Vol 340-341 ◽  
pp. 639-644 ◽  
Author(s):  
Ying Hong Peng ◽  
Qun Feng Chang ◽  
Da Yong Li ◽  
Hu Jie ◽  
Xiao Qin Zeng
Keyword(s):  
Numerical Simulation ◽  
Magnesium Alloy ◽  
Deep Drawing ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Blank Holder Force ◽  
Blank Holder ◽  
Magnesium Alloy Sheet ◽  
Variable Blank Holder Force ◽  
Az31 Magnesium Alloy Sheet

Blank holder force (BHF) plays an important role in sheet metal forming. Previous studies demonstrated that variable blank holder forces can improve the cold formability of steel blank, but the research on the application of variable blank holder force in warm forming of magnesium sheet forming has not been well investigated. In this study, the mechanical property of AZ31 magnesium alloy sheet is measured through some uniaxial tensile tests. In order to obtain the variational rule of the BHF, a mathematical model of BHF is deduced based on the energy theory. The variational rule of the BHF over the punch stroke is analyzed. Finally, three profiles of the BHF curve are designed, and the numerical simulation of warm deep drawing process of magnesium alloy sheet is also performed. A suitable variable blank holder force scheme is obtained through comparison among three results of simulation. The simulation indicates that the limiting drawing ratio of AZ31 magnesium alloy sheet can be improved from 3.0 to 3.5 with the suitable blank holder force varied by an inverted V curve.

Research on the Warm Deep Drawing of AZ31 Magnesium Alloy Sheet Based on DYNAFORM

2011 ◽  
Vol 138-139 ◽  
pp. 754-758
Author(s):  
X.Q. Cao ◽  
J.W. Wang ◽  
Y. Liu ◽  
Cheng Zhong Chi ◽  
L.C. Li ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Magnesium Alloy ◽  
Deep Drawing ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet ◽  
Different Temperatures ◽  
Forming Temperature ◽  
Simulation Results

The effect of forming temperature on the deep drawability (limit drawing ratio (LDR)) of AZ31 magnesium alloy sheet was studied both numerically and experimentally by the use of finite element analysis software DYNAFORM and specially designed warm deep drawing die set. The simulation model was built by SolidWorks 2009, 3-Parameter_Barlat model with BT shell unit was adopted as material model. The constitutive relation of the material was provided by uniaxial isothermal tension tests at different temperatures. After being set, all parameters were referred to famous explicit dynamic solver LS-DYNA. The simulation results showed that the LDR of the AZ31 magnesium alloy sheet is increased with the increase of the temperature initially, but after the temperature reached 423K, the LDR reached the maximum, and then decrease with the increase of temperature in the temperature range studied (room temperature-673K). PTEF was used as lubricant in the experiment. Experimental results showed same trend as numerical simulation results in the studied range of temperature, and LDR reached the maximum of 3.0 at 423K. It is shown that the results of numerical simulation have a good agreement with that of the experiment. By analyzing the microstructure of the drawn-cup walls at different temperatures, it is found that grains were stretched along the direction of tension at temperatures lower than 423K. And there appeared a large number of fine recrystallized grains when forming temperature is 423K showing that dynamic recrystallization occurred during forming process. Dynamic recrystallization conducted completely when forming temperature increased higher than 423K, but the material softening would aggravate with the increase of temperature and on the contrary would do harm to the deep drawing of AZ31 magnesium alloy sheet, resulting the decrease of LDR.

Investigation into AZ31 Sheet Metal Deep Drawing Process at Elevated Temperature

2010 ◽  
Vol 154-155 ◽  
pp. 1244-1250
Author(s):  
Peng Cheng Wang ◽  
Pei Wu ◽  
Zhi Yong Yue
Keyword(s):  
Elevated Temperature ◽  
Magnesium Alloy ◽  
Sheet Metal ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet ◽  
Az31 Sheet

In this paper, mechanical properties of unidirectional hot tensile tests of 3mm thick AZ31 magnesium alloy sheet metal are researched at elevated temperatures and under different tensile speeds. In this basis, thermal deep drawing of cylinders tests for 3mm thick AZ31 magnesium alloy sheet are investigated at elevated drawing temperatures, different drawing speeds and so on. Thermal deep drawing performance showed that set pieces better when elevated temperature and drawing speed range are appropriate to deep drawing.

scholarly journals Dry circular cup deep-drawing of AZ31 magnesium alloy sheet with DLC coating

2010 ◽  
Vol 60 (9) ◽  
pp. 438-443 ◽  
Author(s):  
Shunsuke Tsuda ◽  
Shoichiro Yoshihara ◽  
Yoshitaka Tsuji ◽  
Yu Iriyama
Keyword(s):  
Magnesium Alloy ◽  
Deep Drawing ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Dlc Coating ◽  
Az31 Magnesium Alloy Sheet
Sign in / Sign up

Export Citation Format

Share Document