scholarly journals A high efficiency non-inverting multi device buck-boost DC-DC converter with reduced ripple current and wide bandwidth for fuel cell low voltage applications

2018 ◽  
Vol 15 (2) ◽  
pp. 165-186
Author(s):  
Naik Venkatesh ◽  
Paulson Samuel
Keyword(s):  
Steady State ◽  
Fuel Cell ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Prototype Model ◽  
Voltage Range ◽  
Operating Modes

The voltage produced by the fuel cell (FC) device is unregulated and varies from 0.4 V to 0.8 V on full load to no-load respectively. When these devices are used in low voltage applications and output voltage lies between higher and lower values of input voltage range, it is required to connect a DCDC buck-boost converter to get a fixed output voltage. In this paper, a new noninverting multi device buck boost converter (MDBBC) is proposed, in which the multi device buck and boost converters are connected in cascade and operate individually either in buck or boost operating modes. The paper also includes the steady state analysis of MDDBC based on the state space averaging technique. A prototype model of proposed converter compatible with FCS-1000 Horizon FC model with rating of 270 W, 36 V is designed and developed. The proposed converter is experimentally validated with the results obtained from the prototype model, and results show the superiority of the converter with higher efficiency and lesser ripple current observed under steady state operation of the converter.

scholarly journals High Efficiency Buck-Boost Converter with Three Modes Selection for HV Applications using 0.18 μm Technology

2020 ◽  
Vol 18 (2) ◽  
pp. 137-144
Author(s):  
Fouad Farah ◽  
Mustapha El Alaoui ◽  
Abdelali El Boutahiri ◽  
Mounir Ouremchi ◽  
Karim El Khadiri ◽  
...  
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
High Efficiency ◽  
Power Conversion ◽  
Boost Converter ◽  
Current Control ◽  
Voltage Range ◽  
Operating Modes ◽  
Soft Start

In this paper, we aim to make a detailed study on the evaluation and the characteristics of the non-inverting buck–boost converter. In order to improve the behaviour of the buck-boost converter for the three operating modes, we propose an architecture based on peak current-control. Using a three modes selection circuit and a soft start circuit, this converter is able to expand the power conversion efficiency and reduce inrush current at the feedback loop. The proposed converter is designed to operate with a variable output voltage. In addition, we use LDMOS transistors with low on-resistance, which are adequate for HV applications. The obtained results show that the proposed buck-boost converter perform perfectly compared to others architecture and it is successfully implemented using 0.18 μm CMOS TSMC technology, with an output voltage regulated to 12V and input voltage range of 4-20 V. The power conversion efficiency for the three operating modes buck, boost and buck-boost are 97.6%, 96.3% and 95.5% respectively at load current of 4A.

A Step Down Transformerless Single Switch Integerated Buck and Buck-Boost Converter

2016 ◽  
Vol 5 (3) ◽  
pp. 144
Author(s):  
P. Maithili ◽  
C. Tharani ◽  
J. Nivedha ◽  
D. Soundarrajan
Keyword(s):  
Output Voltage ◽  
Closed Loop ◽  
High Efficiency ◽  
Control Structure ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Application ◽  
Constant Output ◽  
Efficient Power

This paper presents about the designing of the controller for integrated Buck Buck-Boost converter for maintaining the constant DC output voltage. This constant output voltage can be used for low voltage application. The absence of transformer includes the advantages of losses is less, efficient power factor and high efficiency. It provides the simple control structure with the positive constant output voltage .It operates on the closed loop with the designing of the PI controller for a MOSFET switch to provide the gate pulse. Whatever may be the input voltage it will produce the constant output voltage. The converter is successfully done by using MAT Lab/Simulink and verified the error reducing to negligible values.

scholarly journals Quadratic Boost Converter

2021 ◽  
Vol 9 (VII) ◽  
pp. 2010-2014
Author(s):  
Mamidala Hemanth Reddy
Keyword(s):  
Output Voltage ◽  
Semiconductor Device ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Practical Utilization ◽  
Analysis And Design ◽  
Simulink Model ◽  
Grid Connection

The output voltage from the sustainable energy like photovoltaic (PV) arrays and fuel cells will be at less amount of level. This must be boost considerably for practical utilization or grid connection. A conventional boost converter will provides low voltage gain while Quadratic boost converter (QBC) provides high voltage gain. QBC is able to regulate the output voltage and the choice of second inductor can give its current as positive and whereas for boost increases in the voltage will not able to regulate the output voltage. It has low semiconductor device voltage stress and switch usage factor is high. Analysis and design modeling of Quadratic boost converter is proposed in this paper. A power with 50 W is developed with 18 V input voltage and yield 70 V output voltage and the outcomes are approved through recreation utilizing MATLAB/SIMULINK MODEL.

scholarly journals Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 V

2019 ◽  
Vol 9 (4) ◽  
pp. 2230
Author(s):  
Suwarno Suwarno ◽  
Tole Sutikno
Keyword(s):  
Power Electronics ◽  
Wind Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Stabilizer ◽  
Voltage Regulator ◽  
Output Current ◽  
Converter Design

<p>This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.</p>

scholarly journals Modified Multi Input Multilevel DC-DC Boost Converter for Hybrid Energy Systems

2020 ◽  
Vol 9 (4) ◽  
pp. 1067-1072
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Complex Structure ◽  
Energy Systems ◽  
Input Voltage ◽  
Boost Converter ◽  
Design Parameters ◽  
Hybrid Energy ◽  
Hybrid Energy Systems ◽  
Constant Output

DC-DC converters are playing an important role in designing of Electric Vehicles, integration of solar cells and other DC applications. Contemporary high power applications use multilevel converters that have multi stage outputs for integrating low voltage sources. Conventional DC-DC converters use single source and have complex structure while using for Hybrid Energy Systems. This paper proposes a multi-input, multi-output DC-DC converter to produce constant output voltage at different input voltage conditions. This topology is best suitable for hybrid power systems where the output voltage is variable due to environmental conditions. It reduces the requirement of magnetic components in the circuit and also reduces the switching losses. The proposed topology has two parts namely multi-input boost converter and level-balancing circuit. Boost converter increases the input voltage and Level Balancing Circuit produce Multi output. Equal values of capacitors are used in Level Balancing Circuit to ensure the constant output voltage at all output stages. The operating modes of each part are given and the design parameters of each part are calculated. Performance of the proposed topology is verified using MATLAB/Simulink simulation which shows the correctness of the analytical approach. Hardware is also presented to evaluate the simulation results.

scholarly journals A dual inverter combine boost converter qSBI for open-end winding induction motor

2021 ◽  
pp. 1-5
Author(s):  
To Thanh Loi To
Keyword(s):  
Fuel Cell ◽  
Induction Motor ◽  
Output Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Turn On ◽  
Time Simulation ◽  
Low Energies ◽  
Power Switches ◽  
Open End Winding

A Dual boost inverter for open-end winding induction motor has been used to improve the power of the induction motor and reduce the number of power switches. However, this configuration still has many disadvantages: the ac output voltage is less than dc input voltage and switches on the same leg turn on at the same time must be avoided. To solve this problem, this paper presents a dual inverter combine boost converter qSBI for open-end winding induction motor configuration that is used for low energies such as solar energy, fuel cell, and battery. With the proposed configuration, the ac output is higher than the dc input without a DC-DC converter and the switches on the same leg can turn on at the same time. Simulation and experimental results will be presented to demonstrate the new features.

scholarly journals High-efficiency Bidirectional Buck–Boost Converter for Residential Energy Storage System

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3786 ◽  
Author(s):  
Seok-Hyeong Ham ◽  
Yoon-Geol Choi ◽  
Hyeon-Seok Lee ◽  
Sang-Won Lee ◽  
Su-Chang Lee ◽  
...  
Keyword(s):  
Energy Storage ◽  
Output Voltage ◽  
High Efficiency ◽  
Storage System ◽  
Core Loss ◽  
Input Voltage ◽  
Switching Frequency ◽  
Input Output ◽  
Voltage Range ◽  
Output Filter

This paper proposes a bidirectional dc–dc converter for residential micro-grid applications. The proposed converter can operate over an input voltage range that overlaps the output voltage range. This converter uses two snubber capacitors to reduce the switch turn-off losses, a dc-blocking capacitor to reduce the input/output filter size, and a 1:1 transformer to reduce core loss. The windings of the transformer are connected in parallel and in reverse-coupled configuration to suppress magnetic flux swing in the core. Zero-voltage turn-on of the switch is achieved by operating the converter in discontinuous conduction mode. The experimental converter was designed to operate at a switching frequency of 40–210 kHz, an input voltage of 48 V, an output voltage of 36–60 V, and an output power of 50–500 W. The power conversion efficiency for boost conversion to 60 V was ≥98.3% in the entire power range. The efficiency for buck conversion to 36 V was ≥98.4% in the entire power range. The output voltage ripple at full load was <3.59 Vp.p for boost conversion (60 V) and 1.35 Vp.p for buck conversion (36 V) with the reduced input/output filter. The experimental results indicate that the proposed converter is well-suited to smart-grid energy storage systems that require high efficiency, small size, and overlapping input and output voltage ranges.

scholarly journals Design of Control Secheme and Performance Improvement for Multilevel Dc Link Inverter Fed PMBLDC Motor Drive

2013 ◽  
pp. 248-254
Author(s):  
Sagar. M. Lanjewar ◽  
K. Ramsha
Keyword(s):  
Output Voltage ◽  
Permanent Magnets ◽  
High Efficiency ◽  
Input Voltage ◽  
Boost Converter ◽  
Asynchronous Motors ◽  
Bridge Rectifier ◽  
Speed Level ◽  
And Performance ◽  
Copper Losses

PMBLDC motors are gaining a lot of popularity due to their high efficiency as the Permanent Magnets do not carry current which results in negligible copper losses as compared to asynchronous motors. This paper introduces a design for speed control of the PMBLDC motor using multilevel dc link inverter fed by a Boost Converter. The multilevel dc link inverter consist of five level voltage sources, which are controlled by switches. The motor can be driven at different speed level as per its load requirement by making use of five level MLDC Link Inverter. In case of traditional inverter which is only a one level inverter the speed cannot be controlled as per the load requirement. The MLDC link inverter provides the output voltage waveform in step shape form. Thus as the number of cells (n) increases output voltage touches the fundamental component. The input voltage is low, thus to increase the input voltage given to the MLDC link inverter the (Boost Converter) has been designed. The Boost Converter is placed in between (DBR)Diode Bridge Rectifier and (MLDCLI). Both the design and results of Single level inverter and Multilevel Dc Link Inverter are obtained and compared by using the MATLAB Software along with the use of Simulink and Simpower system Tools.

Sign in / Sign up

Export Citation Format

Share Document