scholarly journals Enhancement of proton conductivity through Yb and Zn doping in BaCe0.5Zr0.35Y0.15O3-δ electrolyte for IT-SOFCs

2018 ◽  
Vol 12 (2) ◽  
pp. 180-188 ◽  
Author(s):  
Ahmed Afif ◽  
Nikdalila Radenahmad ◽  
Juliana Zaini ◽  
Mohamed Abdalla ◽  
Seikh Rahman ◽  
...  
Keyword(s):  
High Efficiency ◽  
Low Cost ◽  
Thermo Gravimetric Analysis ◽  
Energy System ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Cubic Crystal ◽  
Zn Doping ◽  
Long Term Stability

The new compositions of BaCe0.5Zr0.3Y0.15-xYbxZn0.05O3-? perovskite electrolytes (x = 0.1 and 0.15) were prepared by solid state synthesis and final sintering at 1500?C. The obtained ceramics were investigated using X-ray diffraction, scanning electron microscopy, thermo-gravimetric analysis and impedance spectroscopy. The refinement of XRD data confirmed cubic crystal structure with Pm3m space group for both samples. SEM morphology showed larger and compacted grains which enables obtaining of high density and high protonic conductivity. The relative densities of the samples were about 99% of the theoretical density after sintering at 1500?C. The protonic conductivities at 650?C were 2.8?10-4 S/cm and 4.2?10-3 S/cm for x = 0.1 and 0.15, respectively. The obtained results showed that higher Yb-content increases the ionic conductivity and both of these perovskites are promising electrolyte for intermediate temperature solid oxide fuel cells to get high efficiency, long-term stability and relatively low cost energy system.

scholarly journals Salt-Resistive Photothermal Materials and Microstructures for Interfacial Solar Desalination

2021 ◽  
Vol 9 ◽  
Author(s):  
Xiaoqiang Yu ◽  
Qian Zhang ◽  
Xin Liu ◽  
Ning Xu ◽  
Lin Zhou
Keyword(s):  
Energy Transfer ◽  
High Efficiency ◽  
Low Cost ◽  
High Energy ◽  
Current Status ◽  
Long Term Stability ◽  
Solar Desalination ◽  
Point Of Use ◽  
Art Research

Solar interfacial evaporation, featured by high energy transfer efficiency, low cost, and environmental compatibility, has been widely regarded as a promising technology for solar desalination. However, the interplay between energy transfer and water transport in the same channels suggests that the tradeoff between high efficiency and long-term stability inherently exists in conventional photothermal nanomaterials. We summarize state-of-the-art research on various anti-salt clogging photothermal microstructures as long-term stable interfacial solar evaporators for solar desalination. The review starts with an overview of the current status and the fundamental limit of photothermal materials for solar desalination. Four representative strategies are analyzed in detail with the most recent experimental demonstrations, including fluid convection enhancement, surface wettability engineering, energy-mass-path decoupling, and surface chemistry engineering. Finally, this article focuses on the challenges in anti-salt clogging solar interfacial evaporators and potential point-of-use applications in the future.

scholarly journals Semiconductor Photocatalyst of Tin Oxide Quantum Dots Prepared in Aqueous Solution for Degradation of Organic Pollutants in Contaminated Water

2021 ◽  
Author(s):  
Jianqiao LIU ◽  
Ye HONG ◽  
Xinyue TIAN ◽  
Xiangxu MENG ◽  
Ge GAO ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Quantum Dots ◽  
High Efficiency ◽  
Low Cost ◽  
Contaminated Water ◽  
Long Term Stability ◽  
High Concentrations ◽  
Average Size ◽  
Source Materials

Stannous chloride and thiourea are used as source materials to prepare SnO2 quantum dots in the aqueous solution by a facile hydrolysis-oxidation process. The quantum dots have an average size of 1.9 nm with good dispersibility as well as long-term stability, and are validated to be an effective photocatalyst for the degradation of organic oil pollutants in contaminated water. The pollutant is removed by the quantum dots exposed to ultraviolet-visible irradiation at room temperature. The optimized condition is concluded to be a solution with quantum dot concentration of 10-3 mol/L and the degradation speed reaches the maximum at the 12 th hour after irradiation. After 48 hours, 91.9 % of octane is removed, concluding a high degradation efficiency. The prepared SnO2 quantum dots are potentially applicable in the remediation of marine environment as they hold the advantages of high efficiency, low cost and being environmental-friendly. The promotion and inhibition mechanisms of the photocatalytic SnO2 QDs at low and high concentrations are discussed.

In-situ stabilization of silver nanoparticles in polymer hydrogels for enhanced catalytic reduction of macro and micro pollutants

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Luqman Ali Shah ◽  
Rida Javed ◽  
Mohammad Siddiq ◽  
Iram BiBi ◽  
Ishrat Jamil ◽  
...  
Keyword(s):  
Catalytic Reduction ◽  
Thermo Gravimetric Analysis ◽  
Activation Parameters ◽  
Reduction Reaction ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
In Situ Stabilization ◽  
Hybrid Hydrogels ◽  
Kinetics Of

AbstractThe in-situ stabilization of Ag nanoparticles is carried out by the use of reducing agent and synthesized three different types of hydrogen (anionic, cationic, and neutral) template. The morphology, constitution and thermal stability of the synthesized pure and Ag-entrapped hybrid hydrogels were efficiently confirmed using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and thermo gravimetric analysis (TGA). The prepared hybrid hydrogels were used in the decolorization of methylene blue (MB) and azo dyes congo red (CR), methyl Orange (MO), and reduction of 4-nitrophenol (4-NP) and nitrobenzene (NB) by an electron donor NaBH4. The kinetics of the reduction reaction was also assessed to determine the activation parameters. The hybrid hydrogen catalysts were recovered by filtration and used continuously up to six times with 98% conversion of pollutants without substantial loss in catalytic activity. It was observed that these types of hydrogel systems can be used for the conversion of pollutants from waste water into useful products.

scholarly journals Wittichenite semiconductor of Cu3BiS3 films for efficient hydrogen evolution from solar driven photoelectrochemical water splitting

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Dingwang Huang ◽  
Lintao Li ◽  
Kang Wang ◽  
Yan Li ◽  
Kuang Feng ◽  
...  
Keyword(s):  
Hydrogen Evolution ◽  
Water Splitting ◽  
Low Cost ◽  
Solar Hydrogen ◽  
Onset Potential ◽  
Term Stability ◽  
Long Term Stability ◽  
Solar Water Splitting ◽  
Current Densities

AbstractA highly efficient, low-cost and environmentally friendly photocathode with long-term stability is the goal of practical solar hydrogen evolution applications. Here, we found that the Cu3BiS3 film-based photocathode meets the abovementioned requirements. The Cu3BiS3-based photocathode presents a remarkable onset potential over 0.9 VRHE with excellent photoelectrochemical current densities (~7 mA/cm2 under 0 VRHE) and appreciable 10-hour long-term stability in neutral water solutions. This high onset potential of the Cu3BiS3-based photocathode directly results in a good unbiased operating photocurrent of ~1.6 mA/cm2 assisted by the BiVO4 photoanode. A tandem device of Cu3BiS3-BiVO4 with an unbiased solar-to-hydrogen conversion efficiency of 2.04% is presented. This tandem device also presents high stability over 20 hours. Ultimately, a 5 × 5 cm2 large Cu3BiS3-BiVO4 tandem device module is fabricated for standalone overall solar water splitting with a long-term stability of 60 hours.

scholarly journals Rapid four-component synthesis of dihydropyrano[2,3-c]pyrazoles using nano-eggshell/Ti(IV) as a highly compatible natural based catalyst

BMC Chemistry ◽  
2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Arefeh Dehghani Tafti ◽  
Bi Bi Fatemeh Mirjalili ◽  
Abdolhamid Bamoniri ◽  
Naeimeh Salehi
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Reaction Times ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solvent Free Conditions ◽  
High Yields ◽  
Work Up

AbstractNano-eggshell/Ti(IV) as a novel naturally based catalyst was prepared, characterized and applied for the synthesis of dihydropyrano[2,3-c]pyrazole derivatives. The characterization of nano-eggshell/Ti(IV) was performed using Fourier Transform Infrared spectroscopy, X-ray Diffraction, Field Emission Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, and Thermo Gravimetric Analysis. Dihydropyrano[2,3-c]pyrazoles were synthesized in the presence of nano-eggshell/Ti(IV) via a four component reaction of aldehydes, ethyl acetoacetate, malononitrile and hydrazine hydrate at room temperature under solvent free conditions. The principal affairs of this procedure are mild condition, short reaction times, easy work-up, high yields, reusability of the catalyst and the absence of toxic organic solvents.

scholarly journals Novel Preparation of Noncovalent Modified GO Using RAFT Polymerization to Reinforce the Performance of Waterborne Epoxy Coatings

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 348 ◽  
Author(s):  
Baolei Liu ◽  
Mingqian Wang ◽  
Ying Liang ◽  
Zhicheng Zhang ◽  
Guohong Ren ◽  
...  
Keyword(s):  
Raft Polymerization ◽  
Salt Spray ◽  
Thermo Gravimetric Analysis ◽  
Analytical Techniques ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Block Polymer ◽  
Reversible Addition ◽  
Waterborne Epoxy ◽  
And Performance

This work launches the first-ever report on the fabrication of waterborne epoxy-graphene oxide (GO) coatings (WEGC) using a block polymer as a dispersant of GO, wherein the block polymer was synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization of acrylic acid and oligo(ethylene glycol) methyl ether methacrylate A number of analytical techniques, such as Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), thermo gravimetric analysis (TGA), and salt spray tests, were utilized to explore the morphology and performance of the WEGC. It was confirmed that POEGMA950-b-PAA attached to the GO nanosheets, increasing the integral space of the sheets. Modified GO (MGO) layers were well-dispersed in the epoxy matrix through the formation of a GO-dispersant-epoxy ternary molecular structure. Furthermore, the presence of MGO substantially influenced the thermal properties, mechanical properties, and anticorrosion performance of the WEGC. TGA, salt spray tests, and pull-off testsshowed that 0.5 wt.% MGO content achieved the greatest improvement in the evaluated properties.

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

Structural and electrochemical properties of Ti–Ru–Fe–O alloys prepared by high energy ball-milling

1998 ◽  
Vol 13 (5) ◽  
pp. 1171-1176 ◽  
Author(s):  
S-H. Yip ◽  
D. Guay ◽  
S. Jin ◽  
E. Ghali ◽  
A. Van Neste ◽  
...  
Keyword(s):  
Electrochemical Properties ◽  
High Energy ◽  
X Ray Diffraction ◽  
Long Term Stability ◽  
Ternary Metal ◽  
Oxide Phases ◽  
Energy Ball ◽  
Diffraction Patterns ◽  
B2 Structure

The structural and electrochemical properties of the Ti–Ru–Fe–O system have been studied over the whole ternary metal compositional range, keeping constant the oxygen content at 30 at.%. The phase diagram was explored systematically by varying the composition of the material along one of the following axes: (i) constant Ru content of 16 at. %; (ii) constant Ti/Ru ratio of 2; (iii) constant Ti/Fe ratio of 1.6. For O/Ti ratios equal or below unity, the most prominent peaks observed in the x-ray diffraction patterns belong to a B2 structure. For O/Ti ratio larger than unity, stable titanium oxide phases are formed, which coexist with a cubic Fe-like or hcp-Ru like phases depending on the Fe/Ru ratio. Powder compositions with stoichiometry close to Ti2RuFeO2 are of interest due to good electrocatalytic properties, long-term stability, and low Ru content.

Investigations on Cu2+-substituted Ni–Zn ferrite nanoparticles

2016 ◽  
Vol 30 (32n33) ◽  
pp. 1650347
Author(s):  
Amarjeet ◽  
Vinod Kumar
Keyword(s):  
Spinel Phase ◽  
Thermo Gravimetric Analysis ◽  
Peak Position ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Zn Ferrite

[Formula: see text] ([Formula: see text] = 0.1, 0.3 and 0.5) nanoparticles were prepared by chemical co-precipitation method. The developed nanoparticles were characterized for structural properties by powder X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. Peak position in the X-ray diffraction pattern confirmed the single spinel phase of the developed particles. Infrared (IR) spectroscopy in mid-IR range showed the presence of characteristic absorption bands corresponding to octahedral and tetrahedral bonds in the spinel structure of prepared samples. Thermo-gravimetric analysis (TGA) measurements showed a considerable weight loss in the developed samples above 700[Formula: see text]C. Frequency dependence of the electrical properties of the developed material pellets was studied in the frequency range of 1 kHz–5 MHz. Temperature dependence of the dielectric constant of [Formula: see text] was studied at different temperatures, i.e. at 425, 450 and 475 K, in the frequency range of 1 kHz–5 MHz. It was found that the electrical conductivity decreases with increasing Cu[Formula: see text] ion content while it increases with the increase in temperature.

Sign in / Sign up

Export Citation Format

Share Document