scholarly journals Electromagnetic characterization of microwave sintered Sr1-xCaxMnO3 (0.0 ≤ x ≤ 0.4) thick films

2013 ◽  
Vol 7 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Rani Pawar ◽  
Ninad Velhal ◽  
Vijaya Puri
Keyword(s):  
Impedance Matching ◽  
Calcium Content ◽  
Frequency Range ◽  
Absorption Loss ◽  
X Ray Diffraction ◽  
X Ray ◽  
X Band ◽  
Electromagnetic Characteristics ◽  
Ku Band

Electromagnetic characteristics of microwave sintered strontium calcium manganites thick film with variation in calcium content have been investigated. The X-ray diffraction analysis reveals tetragonal perovskite structure for all the compositions. The grain size increases with the increase in calcium content. The microwave absorption, complex permittivity, permeability and conductivity are reported in the frequency range of 8.2-18 GHz. The absorption loss is larger in Ku band while insertion loss is larger in X band. The permittivity, permeability and microwave conductivity decreases from X-band to Ku-band. The almost identical values of real part of permittivity and permeability indicate possible application as materials for impedance matching.

Characterization of BaM and PaNi-Based Radar Absorbency (RAM) Behavior with Multilayer Geometry Structure for X-Band Absorption

2019 ◽  
Vol 966 ◽  
pp. 54-59 ◽  
Author(s):  
Mochamad Zainuri ◽  
Dina Andryani
Keyword(s):  
Reflection Loss ◽  
Soft Magnetic Materials ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
Band Frequency ◽  
X Ray ◽  
X Band ◽  
Band Absorption ◽  
Radar Wave

Behavioral characterization of radar absorbent material consisting of Polyaniline (PaNi) and Barium M-Hexaferrite (BaM) has been successfully synthesized by solid state method. Polyaniline conductive material was synthesized using the polymerization method with DBSA dopant. A Radar Absorbing Materials (RAM) is characterized by X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD), Fourier Transform Infrared (FTIR), Four Point Probe (FPP), Scanning Electron Microscope (SEM) and Vector Network Analyzer (VNA). The ion Zn 2+ is dopping into the BAM structure, where Zn 2+ ions replace Fe2+ ions in Hexaferrite barium so that the phase becomes soft magnetic materials . RAM and PANi particles are combined with ship paint to form radar wave absorbent coatings. The layer is coated with multilayer geometry on AH 36 type A steel, with thicknesses of 2.4 mm, 3.6 mm, 4.8 mm and 6 mm respectively. The X-band wave absorption was identified by VNA testing, where the maximum reflection loss value was found at 6mm thickness with a reflection loss value - 32.6 dB at 8.4 GHz frequency. Reflection loss values of multilayer variations with a thickness of 2.4 mm, 3.6mm and 4.8mm each have reflection loss values of -8.02 dB, -19.13 dB and -28.9 dB respectively in the x band frequency range.

Structural, dielectric, ferroelectric and impedance spectroscopic studies on Ba1−xSrxTiO3(0.15 ≤ x ≤ 0.35)

2019 ◽  
Vol 33 (17) ◽  
pp. 1950193 ◽  
Author(s):  
Shukdev Pandey ◽  
Om Parkash ◽  
Devendra Kumar
Keyword(s):  
Equivalent Circuit Model ◽  
Solid State Reaction Method ◽  
Spectroscopic Studies ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
X Band ◽  
Xrd Patterns ◽  
Diffuse Phase

Compositions with x = 0.15, 0.20, 0.25, 0.30 and 0.35 were synthesized in the system [Formula: see text] using conventional solid state reaction method and characterized by X-Ray Diffraction (XRD), Raman spectroscopy and Scanning Electron Microscopy (SEM). Tetragonal phase was confirmed in all the samples using Rietveld refinement of the XRD patterns and observation of their Raman spectra. Dielectric and impedance measurements were carried out in the temperature range 300–723 K in the frequency range 1 Hz to 1 MHz. The samples exhibit diffuse phase transition (DPT). Equivalent circuit model involving combination of Constant Phase angle Elements (CPE) and resistances (R) was developed which represents the data well. Expressions for the values of resistances (R) were established in terms of composition and temperature empirically. P-E loops indicated normal ferroelectric behavior for all the samples. Dielectric constant was also measured in the frequency range 8–12 GHz in the X band of microwaves.

scholarly journals SYNTHESIS AND CHARACTERIZATION OF FEED GRADE MONOCALCIUM PHOSPHATE, Ca(H2PO4)2·H2O IN AQUEOUS MEDIUM

2018 ◽  
Vol 54 (4A) ◽  
pp. 7
Author(s):  
Nguyen Quang Bac
Keyword(s):  
Thermal Analysis ◽  
Aqueous Solution ◽  
Infrared Spectroscopy ◽  
Elevated Temperature ◽  
Calcium Content ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Monocalcium Phosphate ◽  
X Ray

The feed grade monocalcium phosphate monohydrate, Ca(H2PO4)2·H2O was prepared by the reaction of CaCO3 and H3PO4 at elevated temperature in aqueous solution. The obtained precipitates were characterized by powder X-ray diffraction, infrared spectroscopy (FTIR), and thermal analysis (TG, DTA) techniques. The chemical composition of final products was evaluated by analysing the phosphorus and calcium content in the samples.

How Fe60Co40 and Fe72Al28 Nano-Alloys Produced by Mechanical Alloying Behave when Exposed to Microwaves

2008 ◽  
Vol 584-586 ◽  
pp. 977-981 ◽  
Author(s):  
Fadhela Otmane ◽  
S. Bergheul ◽  
Z. Hamlati ◽  
M. Azzaz
Keyword(s):  
Solid Solution ◽  
Mechanical Alloying ◽  
Reflection Loss ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
X Band ◽  
Average Grain Size ◽  
Xrd Patterns

Fe60Co40 and Fe72Al28 nano-alloys were synthesized from elemental powders via highenergy mechanical alloying. The prepared samples were characterized using X-ray diffraction, scanning electron microscopy and X-band waveguide to measure the reflection loss in a frequency range of 9-10 GHz. The XRD patterns show that disordered Fe60Co40 solid solution with a bodycentred cubic structure is formed for milling times longer than 12 h, and after 4h milling, the solid solution Fe72Al28 has been largely formed. Morphological studies indicate an average grain size of 10 to 15 nm. The microwave- absorbing characteristic reveal good performance for Fe60Co40 compared to Fe72Al28, the maximum reflection loss is about -12 dB for the absorber.

scholarly journals Sintesis Ferroelektrik BaZrxTi1-xO3 Dengan Variasi Zirkonium Terhadap Struktur Kristal dan Konstanta Dielektrik

2021 ◽  
Vol 9 (1) ◽  
pp. 47-54
Author(s):  
Yunita Subarwanti ◽  
◽  
Erni Mariana ◽  
Keyword(s):  
Crystal Structure ◽  
Dielectric Constant ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Dielectric Constant ◽  
Die Pressing

This study aims to determine influence addition Zr against the crystal structure and dielectric constant; and to know the influence of variations temperature sintering on addition mole Zr. Barium Zirconium Titanate (BaZrxTi1-xO3) have been made with variation zirconium (Zr) 1%, 5%, 10%, and 20% by solid state reaction method, that is blanded BaTiO3, TiO2 and ZrO2 powder. BaZrxTi1-xO3 powder is printed with die pressing and press hidrolik, then the samples were sintered by furnace at 900oC and 1000oC with holding time 2 hours. Characterization of samples use X-Ray Diffraction and Resistance Capacitance Inductance (RCL meter). Based on result obtained, the larger Zr content cause dielectric constant decreasing because crystal structure have been change from tetragonal (Zr = 1% and 5%) to cubic (Zr = 10% and 20%). The result from X-Ray Diffraction already match with data base ICDD no#360019. Measurement of dielectric constant (K) performed in the frequency range 1 kHz to 100 kHz and the highest value at Zr content 1%, because The dielectric constant decreasing with the larger Zr content. The maximum dielectric constant is obtained at mol Zr 5% and sintering temperature 1000oC, that is 150. The minimum dielectric constant is obtained at mol Zr 20% and sintering temperature 900oC, that is 62.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

High Resolution Replication of Organoclay Surfaces

1982 ◽  
Vol 40 ◽  
pp. 576-577
Author(s):  
W. W. Barker ◽  
W. E. Rigsby ◽  
V. J. Hurst ◽  
W. J. Humphreys
Keyword(s):  
Clay Mineral ◽  
Organic Molecule ◽  
Organic Molecules ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Naturally Occurring ◽  
Silicate Layers ◽  
Mineral Identification

Experimental clay mineral-organic molecule complexes long have been known and some of them have been extensively studied by X-ray diffraction methods. The organic molecules are adsorbed onto the surfaces of the clay minerals, or intercalated between the silicate layers. Natural organo-clays also are widely recognized but generally have not been well characterized. Widely used techniques for clay mineral identification involve treatment of the sample with H2 O2 or other oxidant to destroy any associated organics. This generally simplifies and intensifies the XRD pattern of the clay residue, but helps little with the characterization of the original organoclay. Adequate techniques for the direct observation of synthetic and naturally occurring organoclays are yet to be developed.

Synthesis and characterization of TiN / Ti / AISI 410 coatings

2018 ◽  
Vol 2 (1) ◽  
pp. 7
Author(s):  
S Chirino ◽  
Jaime Diaz ◽  
N Monteblanco ◽  
E Valderrama
Keyword(s):  
Synthesis And Characterization ◽  
Photoemission Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Columnar Grains ◽  
Tin Thin Films ◽  
Steel Aisi ◽  
Interacting Surfaces ◽  
Stainless Steel Aisi

The synthesis and characterization of Ti and TiN thin films of different thicknesses was carried out on a martensitic stainless steel AISI 410 substrate used for tool manufacturing. The mechanical parameters between the interacting surfaces such as thickness, adhesion and hardness were measured. By means of the scanning electron microscope (SEM) the superficial morphology of the Ti/TiN interface was observed, finding that the growth was of columnar grains and by means of EDAX the existence of titanium was verified.  Using X-ray diffraction (XRD) it was possible to observe the presence of residual stresses (~ -3.1 GPa) due to the different crystalline phases in the coating. Under X-ray photoemission spectroscopy (XPS) it was possible to observe the molecular chemical composition of the coating surface, being Ti-N, Ti-N-O and Ti-O the predominant ones.

Studies on the Preparation, Characterization and Solubility of -Cyclodextrin-Roxythromycin Inclusion Complexes

2009 ◽  
Vol 2 (2) ◽  
pp. 523-530
Author(s):  
D. Nagasamy Venkatesh ◽  
S. Karthick ◽  
M. Umesh ◽  
G. Vivek ◽  
R.M. Valliappan ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Inclusion Complexes ◽  
Phase Solubility ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ir Studies ◽  
Poorly Soluble ◽  
Poorly Soluble Drug

Roxythromycin/ β-cyclodextrin (Roxy/ β-CD) dispersions were prepared with a view to study the influence of β-CD on the solubility and dissolution rate of this poorly soluble drug. Phase-solubility profile indicated that the solubility of roxythromycin was significantly increased in the presence of β-cyclodextrin and was classified as AL-type, indicating the 1:1 stoichiometric inclusion complexes. Physical characterization of the prepared systems was carried out by differential scanning calorimetry (DSC), X-ray diffraction studies (XRD) and IR studies. Solid state characterization of the drug β-CD binary system using XRD, FTIR and DSC revealed distinct loss of drug crystallinity in the formulation, ostensibly accounting for enhancement of dissolution rate.

New Coordination Compounds of Fe(III) with Organic Ligands

2009 ◽  
Vol 59 (12) ◽  
Author(s):  
Mihaela Flondor ◽  
Ioan Rosca ◽  
Doina Sibiescu ◽  
Mihaela-Aurelia Vizitiu ◽  
Daniel-Mircea Sutiman ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Complex Compounds ◽  
Organic Ligands ◽  
X Ray Diffraction ◽  
X Ray ◽  
Elemental Chemical Analysis ◽  
Structural Formulae ◽  
Paramagnetic Properties

In this paper the synthesis and the study of some complex compounds of Fe(III) with ligands derived from: 2-(4-chloro-phenylsulfanyl)-1-(2-hydroxy-3,5-diiodo-phenyl)-ethanone (HL1), 1-(3,5-dibromo-2-hydroxy-phenyl)-2-phenylsulfanyl-ethanone(HL2), and 2-(4-chloro-phenylsulfanyl)-1-(3,5-dibromo-2-hydroxy-phenyl)-ethanone (HL3) is presented. The characterization of these complexes is based on method as: the elemental chemical analysis, IR and ESR spectroscopy, M�ssbauer, the thermogravimetric analysis and X-ray diffraction. Study of the IR and chemical analysis has evidenced that the precipitates form are a complexes and the combination ratio of M:L is 1:2. The central atoms of Fe(III) presented paramagnetic properties and a octaedric hybridization. Starting from this precipitation reactions, a method for the gravimetric determination of Fe(III) with this organic ligands has been possible. Based on the experimental data on literature indications, the structural formulae of the complex compounds are assigned.

Sign in / Sign up

Export Citation Format

Share Document