scholarly journals Ozone absorption in a mechanically stirred reactor

2007 ◽  
Vol 72 (8-9) ◽  
pp. 847-855 ◽  
Author(s):  
Ljiljana Takic ◽  
Vlada Veljkovic ◽  
Miodrag Lazic ◽  
Srdjan Pejanovic
Keyword(s):  
Mass Transfer ◽  
Liquid Phase ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Plug Flow ◽  
Operating Conditions ◽  
Volumetric Mass Transfer Coefficient ◽  
Pseudo First Order Reaction ◽  
Ozone Absorption ◽  
Stirred Reactor

Ozone absorption in water was investigated in a mechanically stirred reactor, using both the semi-batch and continuous mode of operation. A model for the precise determination of the volumetric mass transfer coefficient in open tanks without the necessity of the measurement the ozone concentration in the outlet gas was developed. It was found that slow ozone reactions in the liquid phase, including the decomposition of ozone, can be regarded as one pseudo-first order reaction. Under the examined operating conditions, the liquid phase was completely mixed, while mixing in a gas phase can be described as plug flow. The volumetric mass transfer coefficient was found to vary with the square of the impeller speed. .

scholarly journals Determination of the ozone volumetric mass transfer coefficient in bubble column with two-fluid nozzle gas distributor

2015 ◽  
Vol 69 (5) ◽  
pp. 553-559 ◽  
Author(s):  
Milica Djekovic-Sevic ◽  
Nevenka Boskovic-Vragolovic ◽  
Ljiljana Takic ◽  
Radmila Garic-Grulovic ◽  
Srdjan Pejanovic
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Bubble Column ◽  
Operating Conditions ◽  
Volumetric Mass Transfer Coefficient ◽  
Gas Distributor ◽  
Liquid Mass Transfer ◽  
Two Fluid

Experimental investigation of gas-liquid mass transfer of ozone in water, in bubble column with two-fluid nozzle gas distributor (BKDM), under different operating conditions, are presented in this work. The main objective was to determine the ozone volumetric mass transfer coefficient, kL a, in calm uniform section of the column, under different values of gas and liquid flow rates. Obtained values of these coefficients were compared with the values in countercurrent bubble column. The critical liquid flowrate, when gas hold up reaches its maximum, was experimentally determined. It was shown that the maximum value of the ozone volumetric mass transfer coefficient is obtained just when liquid flowrate is at its critical value.

Influence of Physical Properties of Phases on Hydrodynamics and Mass Transfer Characteristics of a Liquid-Liquid Circular Microchannel

2016 ◽  
Author(s):  
Mehdi Sattari-Najafabadi ◽  
Bengt Sundén ◽  
Zan Wu ◽  
Mohsen Nasr Esfahany
Keyword(s):  
Mass Transfer ◽  
Physical Properties ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Rate Ratio ◽  
Operating Conditions ◽  
Flow Rate Ratio ◽  
Internal Diameter ◽  
Volumetric Mass Transfer Coefficient

The influences of operating conditions and physical properties of the two phases on the hydrodynamics and mass transfer in a circular liquid-liquid microchannel have been investigated. The polytetrafluoroethylene (PTFE) microchannel has an internal diameter of 0.7 mm and a T-shaped mixing junction. Sodium hydroxide solution was used as the aqueous phase. N-hexane and toluene were employed as the organic phases to investigate the effect of physical properties. Regarding the results, at constant total flow rate, raising the flow rate ratio enhanced the overall volumetric mass transfer coefficient. Using toluene as the organic solvent enhanced the overall volumetric mass transfer coefficient in average by 64.7% and 100.27% comparing to n-hexane-water at flow rate ratio of 1 and 0.5, respectively. This increment resulted in a decrement in the required mass transfer time and length in the microchannel. The length of the slugs had no considerable variation as n-hexane was replaced with toluene. Thus, the significant improvement of the overall volumetric mass transfer coefficient was because of the increment of the overall mass transfer coefficient, not the specific interfacial area.

scholarly journals Effects of geometric parameters on volumetric mass transfer coefficient of non-Newtonian fluids in stirred tanks

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Haider Ali ◽  
Sofia Zhu ◽  
Jannike Solsvik
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Scale Up ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Volumetric Mass Transfer Coefficient ◽  
Transfer Coefficients ◽  
Stirred Tanks

Abstract Scaling up stirred tanks is a significant challenge because of the research gaps between laboratory and industrial-scale setups. It is necessary to understand the effects of scale-up on the mass transfer in stirred tanks, and this requires meticulous experimental analysis. The present study investigates the effects of tank size and aspect ratio ( H L T ${H}_{L}}{T}$ ) on the volumetric mass transfer coefficients of shear-thinning fluids. The experiments were conducted in three stirred tanks of different sizes (laboratory and pilot scale) and geometries (standard and nonstandard). H L T ${H}_{L}}{T}$ was 1 for the standard tanks and 3.5 for the nonstandard stirred tanks. Three sizes of stirred tanks were used: 11 L with H L T ${H}_{L}}{T}$ of 1, 40 L with H L T ${H}_{L}}{T}$ of 3.5, and 47 L with H L T ${H}_{L}}{T}$ of 1. Impeller stirring speeds and gas flow rates were in the range of 800–900 rev min−1 and 8–10 L min−1, respectively. The volumetric mass transfer coefficient was estimated based on the dissolved oxygen concentration in the fluids, and the effects of rheology and operating conditions on the volumetric mass transfer coefficient were observed. The volumetric mass transfer coefficient decreased as tank size increased and increased with an increase in operating conditions, but these effects were also clearly influenced by fluid rheology. The impacts of scale-up and operating conditions on the volumetric mass transfer coefficient decreased as liquid viscosity increased.

scholarly journals Mass Transfer Correlation and Optimization of Carbon Dioxide Capture in a Microchannel Contactor: A Case of CO2-Rich Gas

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5465
Author(s):  
Nattee Akkarawatkhoosith ◽  
Wannarak Nopcharoenkul ◽  
Amaraporn Kaewchada ◽  
Attasak Jaree
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Co2 Capture ◽  
Volumetric Flow Rate ◽  
Absorption Efficiency ◽  
Operating Conditions ◽  
Molar Ratio ◽  
Volumetric Mass Transfer Coefficient

This work focused on the application of a microchannel contactor for CO2 capture using water as absorbent, especially for the application of CO2-rich gas. The influence of operating conditions (temperature, volumetric flow rate of gas and liquid, and CO2 concentration) on the absorption efficiency and the overall liquid-side volumetric mass transfer coefficient was presented in terms of the main effects and interactions based on the factorial design of experiments. It was found that 70.9% of CO2 capture was achieved under the operating conditions as follows; temperature of 50 °C, CO2 inlet fraction of 53.7%, total gas volumetric flow rate of 150 mL min−1, and adsorbent volumetric flow rate of 1 mL min−1. Outstanding performance of CO2 capture was demonstrated with the overall liquid-side volumetric mass transfer coefficient of 0.26 s−1. Further enhancing the system by using 2.2 M of monoethanolamine in water (1:1 molar ratio of MEA-to-CO2) boosted the absorption efficiency up to 88%.

Sign in / Sign up

Export Citation Format

Share Document