scholarly journals Influence of different functionalization methods of multi-walled carbon nanotubes on the properties of poly(L-lactide) based nanocomposites

2019 ◽  
Vol 73 (3) ◽  
pp. 183-196 ◽  
Author(s):  
Nevena Vukic ◽  
Ivan Ristic ◽  
Milena Marinovic-Cincovic ◽  
Radmila Radicevic ◽  
Branka Pilic ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Ft Ir ◽  
Walled Carbon Nanotubes ◽  
Functionalized Mwcnts

This paper presents influence of the type of carbon nanotube functionalization on properties of poly(L-lactide) (PLLA) based nanocomposite materials. For this purpose surface modifications of multi-walled carbon nanotubes (MWCNTs) were performed by chemical and irradiation techniques, while thermo gravimetric analysis, UV-Visible and Fourier-transform infrared (FT-IR) spectroscopies confirmed successful covalent functionalization. Series of PLLA bionanocom-posites with different contents of functionalized MWCNTs (0.7; 1.6; 2.1 wt%), were synthesized via ring-opening solution polymerisation of L-lactide. FT-IR analysis confirmed that grafting of L-lactide, under controlled condition, is possible to perform starting from the surface of functionalized MWCNTs. From differential scanning calorimetry results it was concluded that even low contents of chemically and irradiation functionalized MWCNTs had a significant effect on thermal properties of the prepared nanocomposites, raising the values of melting and glass transition temperatures. Thermogravimetric analysis (TGA) has shown that the degradation onset temperature for composites with chemically functionalized MWCNTs, was much higher than that for the neat poly(L-lactide) sample and composites with irradiation functionalized MWCNTs. Morphology studies by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that poly(L-lactide) covered surfaces and separated functionalized MWCNTs. Good dispersion of carbon nanotubes in polymer matrix enabled conductivity of synthesized materials, as determined by conductivity tests.

Ultrasound promoted green oxidation of alkenes with hydrogen peroxide in the presence of iron porphyrins supported on multi-walled carbon nanotubes

2015 ◽  
Vol 19 (04) ◽  
pp. 622-630 ◽  
Author(s):  
Saeed Rayati ◽  
Zahra Sheybanifard
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Hydrogen Peroxide ◽  
Heterogeneous Catalyst ◽  
Multi Wall Carbon Nanotubes ◽  
Mechanical Stirring ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Ft Ir ◽  
Walled Carbon Nanotubes

In the present work, oxidation of alkenes with hydrogen peroxide in the presence of meso-tetrakis(4-hydroxyphenyl)porphyrinatoiron(III) chloride supported onto surface of functionalized multi-wall carbon nanotubes (FMWCNT), [ Fe ( THPP ) Cl@MWCNT ], is reported. The simple heterogeneous catalyst was characterized by FT-IR spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and also thermal analysis. The amount of the catalyst loaded on the nanotubes was determined by atomic absorption spectroscopy. This heterogeneous catalyst proved to be an efficient and green catalyst and was successfully able to activate hydrogen peroxide without any additive toward the oxidation of alkenes in ethanol as a green solvent. Performance of the catalyst in oxidation of various alkenes was inspected under reflux, ultrasonic irradiation and mechanical stirring. Moreover, the catalyst can be reused several times under similar conditions.

Study on Preparation and Properties of Hyperbranched Polyurethane/Multi-Walled Carbon Nanotubes Composites

2013 ◽  
Vol 716 ◽  
pp. 103-108
Author(s):  
Ning Sun ◽  
Jun Chao Wang ◽  
Chun Yun Feng ◽  
Yi Biao Li ◽  
Shao Hua Jiang ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Hydroxyl Groups ◽  
Gravimetric Analysis ◽  
Test Results ◽  
Scanning Calorimetry ◽  
Hyperbranched Polyurethane ◽  
Multi Walled Carbon Nanotubes ◽  
Ft Ir ◽  
Walled Carbon Nanotubes ◽  
Better Than

With the Grafting to method, the hyperbranched polyurethane/multi-walled carbon nanotubes composites (MWNT-HBPU) was prepared. The reaction mechanism was covalently grafting hyperbranched polyurethane to multi-walled carbon nanotubes,through the reaction of the isocyanate groups of multi-walled carbon nanotubes (MWNT-NCO) and the hydroxyl groups of homemade hyperbranched polyurethane (HBPU). The structure and properties of the composites was studied by Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy (Raman), Thermal gravimetric analysis (TG) and Differential scanning calorimetry (DSC). The test results of FT-IR and TG showed that the prepared product was MWNT-HBPU; the DSC results demonstrated that the glass transition temperature of HBPU was significantly increased from 91.9°C to more than 99.7°C by the addition of MWNT-HBPU; the dispersion of the MWNT-HBPU was much better than the pure MWNT in solvents, such as N, N-dimethylformamide , Dimethyl sulfoxide etc.

Reinforcing Effects of Poly(D-Lactide)-g-Multiwall Carbon Nanotubes on Polylactide Nanocomposites

2015 ◽  
Vol 15 (10) ◽  
pp. 8086-8092 ◽  
Author(s):  
Jeong Hee Yang ◽  
Jae Yun Lee ◽  
In-Joo Chin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Testing Machine ◽  
Multiwall Carbon Nanotubes ◽  
Hydroxyl Groups ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Polylactide (PLA) nanocomposites with multi-walled carbon nanotubes (MWNTs) grafted with poly(L-lactide) or poly(D-lactide) were prepared by solution casting, and their thermal and mechanical properties were evaluated. MWNTs containing hydroxyl groups were treated by ring-opening polymerization of either L-lactide or D-lactide. Fourier transform infrared spectroscopy confirmed that the MWNT surfaces had been modified by the PLLA or PDLA chains. The thermal properties were measured by differential scanning calorimetry and thermogravimetric analysis. The mechanical properties were examined using a universal testing machine. The morphology of the fractured surfaces of the PLA nanocomposites was observed by scanning electron microscopy and transmission electron microscopy. PDLA-g-MWNTs were dispersed more uniformly compared to PLLA-g-MWNTs in the PLA matrix. The incorporation of PDLA-g-MWNTs greatly improved the tensile strength of the nanocomposites regardless of the contents. Thermal analysis revealed different characteristics at specific composites depending on the type of modification.

MANUFACTURING AND CHARACTERIZATION OF CARBON NANOTUBE/POLYETHYLENE COMPOSITES

2005 ◽  
Vol 04 (01) ◽  
pp. 55-72 ◽  
Author(s):  
HASSAN MAHFUZ ◽  
ASHFAQ ADNAN ◽  
VIJAYA K. RANGARI ◽  
SHAIK JEELANI
Keyword(s):  
Carbon Nanotubes ◽  
Thermo Gravimetric Analysis ◽  
Extrusion Direction ◽  
Extrusion Process ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Neat Polymer ◽  
Single Screw Extrusion ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

The present study describes a method to fabricate polymer matrix nanocomposites by reinforcing multi-walled carbon nanotubes through an extrusion process. Linear low density polyethylene (LLDPE) powder and multi-walled carbon nanotubes (CNTs) are first dry mixed and extruded in the form of filaments by a single screw extrusion process. After extrusion, the filament is partially cooled by chilled air, dried, and continuously wound in a spool. The filaments are then laid in roving, stacked in a unidirectional fashion, and consolidated in a compression molding machine to come up with laminated composites. Thermo gravimetric analysis (TGA) has been performed to compare the thermal stability of as-fabricated composites with the neat polymer. The TGA result shows that the extruded composites are thermally more stable than their neat counterparts. The crystalline nature of CNTs and of as-fabricated composites were identified by X-ray diffraction (XRD) studies. The XRD results indicate that the nanocomposite materials are more crystalline than the neat systems, and the differential scanning calorimetry studies also confirmed the same trend. The scanning electron microscopy result showed that the sizes of extruded neat and nanophased filaments were about 117 and 73 μm, respectively. Tensile coupons from the consolidated panels were then extracted both in longitudinal (0°) and in transverse (90°) directions and tested in a Minimat Tester. It was found that with the addition of 2% by weight of CNTs in LLDPE, the tensile strength and modulus of the composite has increased by about 34 and 38%, respectively. The (0°) and (90°) coupons have also demonstrated that there are directional effects in the tensile response, which is believed to have been caused by the alignment of CNTs during the extrusion process. It is our understanding that such improvement in properties is because of the increase in crystallinity of the polymer due to CNT infusion, and also due to the alignment of CNTs in the extrusion direction in the nanocomposites. Details of the fabrication procedures, synthesis of composites, and mechanical testing are included in the paper.

scholarly journals Purification for Carbon Nanotubes Synthesized by Flame Fragments Deposition via Hydrogen Peroxide and Acetone

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2342 ◽  
Author(s):  
Asmaa H. Hammadi ◽  
Ahmed M. Jasim ◽  
Firas H. Abdulrazzak ◽  
Abdulkareem M. A. Al-Sammarraie ◽  
Yacine Cherifi ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Hydrogen Peroxide ◽  
Polyaromatic Hydrocarbons ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
Liquefied Petroleum Gas ◽  
Force Microscopy ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Carbon nanotubes (CNTs) are synthesized by the flame fragment deposition (FFD) technique using Iraqi liquefied petroleum gas (LPG) as a source of carbon in a hand-made reactor at a low temperature (160 °C) without using a catalyst. Purification of the multi-walled carbon nanotubes (MWCNTs) is carried out using a two-step process consisting of sonication in 30 wt.% hydrogen peroxide (H2O2) solution at room temperature to remove amorphous impurities adhering to the walls of the CNTs and carbon nanoparticles (CNPs), followed by sonication in an acetone bath to remove the polyaromatic hydrocarbons (PAH) formed during the LPG gas burning. Comprehensive characterizations such as X-ray diffraction (XRD), atomic force microscopy (AFM), thermo-gravimetric analysis (TGA), and transmission electron microscopy (TEM) were conducted to verify the efficiency of the purification process. The results clearly demonstrated that this process is promising for the purification of the synthesized CNTs.

scholarly journals Biocompatibility Characteristics of Titanium Coated with Multi Walled Carbon Nanotubes—Hydroxyapatite Nanocomposites

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 224 ◽  
Author(s):  
Jung-Eun Park ◽  
Yong-Seok Jang ◽  
Tae-Sung Bae ◽  
Min-Ho Lee
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Sol Gel ◽  
Pure Titanium ◽  
Cell Proliferation And Differentiation ◽  
Transmission Electron ◽  
Proliferation And Differentiation ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Multi walled carbon nanotubes-hydroxyapatite (MWCNTs-HA) with various contents of MWCNTs was synthesized using the sol-gel method. MWCNTs-HA composites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). HA particles were generated on the surface of MWCNT. Produced MWCNTs-HA nanocomposites were coated on pure titanium (PT). Characteristic of the titanium coated MWCNTs-HA was evaluated by field-emission scanning electron microscopy (FE-SEM) and XRD. The results show that the titanium surface was covered with MWCNTs-HA nanoparticles and MWCNTs help form the crystalized hydroxyapatite. Furthermore, the MWCNTs-HA coated titanium was investigated for in vitro cellular responses. Cell proliferation and differentiation were improved on the surface of MWCNT-HA coated titanium.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

scholarly journals Carbon Nanofibers from Carbon Nanotubes by 1.2 keVAr+Sputtering at Room Temperature

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Shuang-Xi Xue ◽  
Qin-Tao Li ◽  
Xian-Rui Zhao ◽  
Qin-Yi Shi ◽  
Zhi-Gang Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Carbon Nanofibers ◽  
Carbon Nanoparticles ◽  
Room Temperature ◽  
Ion Irradiation ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Carbon Nanowires

Multi-walled carbon nanotubes (MWCNTs) were irradiated by 1.2 keV Ar ion beams for 15–60 min at room temperature with current density of 60 µA/cm2. The morphology and microstructure are investigated by scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The results show that carbon nanofibers are achieved after 60 min ion irradiation and the formation of carbon nanofibers proceeds through four periods, carbon nanotubes—amorphous carbon nanowires—carbon nanoparticles along the tube axis—conical protrusions on the nanoparticles surface—carbon nanofibers from the conical protrusions.

Biosynthesis and Characterization of Copper Nanoparticles Using a Bioflocculant Extracted from Alcaligenis faecalis HCB2

2019 ◽  
Vol 11 (11) ◽  
pp. 1064-1070 ◽  
Author(s):  
Nkosinathi G. Dlamini ◽  
Albertus K. Basson ◽  
V. S. R. Rajasekhar Pullabhotla
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Copper Nanoparticles ◽  
Average Particle Size ◽  
Thermo Gravimetric Analysis ◽  
Average Particle ◽  
Gravimetric Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir

Bioflocculant from Alcaligenis faecalis HCB2 was used in the eco-friendly synthesis of the copper nanoparticles. Nanoparticles were characterized using a scanning electron microscope (SEM), transmission electron microscopy (TEM), UV-visible spectroscopy, thermo gravimetric analysis (TGA) and Fourier Transform Infrared Spectroscopy (FT-IR). The transmission electron microscopy images showed close to spherical shapes with an average particle size of ∼53 nm. Energy-dispersive X-ray spectroscopy analysis confirmed the presence of the Cu nanopartilces and also the other elements such as O, C, P, Ca, Cl, Na, K, Mg, and S originated from the bioflocculant. FT-IR results showed the presence of the –OH and –NH2 groups, aliphatic bonds, amide and Cu–O bonds. Powder X-ray diffraction peaks confirmed the presence of (111) and (220) planes of fcc structure at 2 of 33° and 47° respectively with no other impurity peaks.

Sign in / Sign up

Export Citation Format

Share Document