scholarly journals Quantitative characterization of mns inclusions in S355 steel regarding to solidification rate

2013 ◽  
Vol 67 (2) ◽  
pp. 331-336
Author(s):  
Aida Mahmutovic
Keyword(s):  
Chemical Composition ◽  
Special Interest ◽  
Electron Probe ◽  
Solidification Rate ◽  
Equilibrium Phase ◽  
Casting Surface ◽  
Electron Probe Microanalyzer ◽  
Metallic Inclusions ◽  
Thermo Calc Software ◽  
Liquidus Temperatures

A practice of special interest for metallurgical steelmaking is the relationship between redistribution of solute elements and dendrite microsegregation that occurs during solidification. These phenomena have a significant impact on the final properties of cast and forged products. In this paper, a calculation of the characteristic chemical phases in S355 steel using a software program Thermo-Calc is presented. Also, the paper presents experimental measurements of the dendrites size and non-metallic inclusions using optical and electron probe microanalyzer, as well as the calculation of the local solidification rate on the particular example. These phenomena are of special interest when it comes to thin castings and higher cooling rates. Thin castings require higher quality of casting surface, corresponding distribution, and character than those of non-metallic inclusions. Thermo-calc software was used for calculation of equilibrium phases, temperature ranges of solidification of tested material, and temperature range for developing characteristic equilibrium phase. It was found that during solidification and cooling processes manganese sulphide inclusions were formed. Additionally, accurate values for solidus and liquidus temperatures, which coincide with the values of solidus and liquidus temperatures obtained by the Thermo Calc, were calculated. Using optical and electron probe microanalyzer, the type of inclusions were confirmed, whereas chemical composition and size measurement of dendrites, and formed non-metallic inclusions were determined. Mapping and Linescan methods were used to examine the size and exact chemical composition of sulphides in atomic percents. Using secondary dendrites local solidification rate was calculated (for casting surface area solidification rate was 5 K/s). This paper gives contribution to better understanding the influence of cooling rate on casting microstructure formation and dendrites, which essentially determine the size of non-metallic inclusions and their redistribution.

Convenient analysis of chemical composition of clay fraction of sediment by electron probe microanalyzer

2017 ◽  
Vol 51 (6) ◽  
pp. 583-588 ◽  
Author(s):  
Youko Miyoshi ◽  
Kazuhiko Shimada ◽  
Hiroshi Sato ◽  
Seiichiro Uehara ◽  
Jun-ichiro Ishibashi
Keyword(s):  
Chemical Composition ◽  
Electron Probe ◽  
Clay Fraction ◽  
Electron Probe Microanalyzer

Application Of Electron Probe Analyses Of Minerals In Discussing The Relationship Between Ductile Deformation And Metamorphism

1990 ◽  
Vol 48 (2) ◽  
pp. 250-251
Author(s):  
Fan Guochuan ◽  
Sun Zhongshi
Keyword(s):  
Chemical Composition ◽  
Shear Deformation ◽  
Electron Probe ◽  
General Rule ◽  
Granulite Facies ◽  
Ductile Deformation ◽  
Higher Temperature ◽  
Ductile Shear ◽  
The Relationship ◽  
Ductile Shear Deformation

Under influence of ductile shear deformation, granulite facies mineral paragenesis underwent metamorphism and changes in chemical composition. The present paper discusses some changes in chemical composition of garnet in hypers thene_absent felsic gnesiss and of hypersthene in rock in early and late granulite facies undergone increasing ductile shear deformation .In garnet fetsic geniss, band structures were formed because of partial melting and resulted in zoning from massive⟶transitional⟶melanocrate zones in increasing deformed sequence. The electron-probe analyses for garnet in these zones are listed in table 1 . The Table shows that Mno, Cao contents in garnet decrease swiftly from slightly to intensely deformed zones.In slightly and moderately deformed zones, Mgo contents keep unchanged and Feo is slightly lower. In intensely deformed zone, Mgo contents increase, indicating a higher temperature. This is in accord with the general rule that Mgo contents in garnet increase with rising temperature.

Quantitative EPMA of nitrogen : A tricky element in the electron-probe microanalyzer

1992 ◽  
Vol 50 (2) ◽  
pp. 1622-1623
Author(s):  
G.F. Bastin ◽  
H.J.M. Heijligers
Keyword(s):  
Background Subtraction ◽  
Electron Probe ◽  
Detection System ◽  
Higher Order ◽  
Light Elements ◽  
Strong Suppression ◽  
Electron Probe Microanalyzer ◽  
Quantitative Epma ◽  
Peak Count ◽  
Lead Stearate

Among the ultra-light elements B, C, N, and O nitrogen is the most difficult element to deal with in the electron probe microanalyzer. This is mainly caused by the severe absorption that N-Kα radiation suffers in carbon which is abundantly present in the detection system (lead-stearate crystal, carbonaceous counter window). As a result the peak-to-background ratios for N-Kα measured with a conventional lead-stearate crystal can attain values well below unity in many binary nitrides . An additional complication can be caused by the presence of interfering higher-order reflections from the metal partner in the nitride specimen; notorious examples are elements such as Zr and Nb. In nitrides containing these elements is is virtually impossible to carry out an accurate background subtraction which becomes increasingly important with lower and lower peak-to-background ratios. The use of a synthetic multilayer crystal such as W/Si (2d-spacing 59.8 Å) can bring significant improvements in terms of both higher peak count rates as well as a strong suppression of higher-order reflections.

Measurement And Simulation Of X-Ray Emission From Multilayered Structures In Electron Probe Microanalysis.

1999 ◽  
Vol 5 (S2) ◽  
pp. 78-79
Author(s):  
C. Merlet ◽  
X. Llovet ◽  
F. Salvat
Keyword(s):  
Electron Probe ◽  
Numerical Models ◽  
Carbon Layer ◽  
Single Element ◽  
Surface Ionization ◽  
Copper Films ◽  
Multilayered Structures ◽  
X Ray ◽  
Electron Probe Microanalyzer ◽  
Quantitative Epma

Studies of x-ray emission from thin films on substrates using an electron probe microanalyzer (EPMA) provide useful information on the characteristics of x-ray generation by electron beams. In this study, EPMA measurements of multilayered samples were performed in order to test and improve analytical and numerical models used for quantitative EPMA. These models provide relatively accurate results for samples consisting of layers with similar average atomic numbers, because of their similar properties regarding electron transport and x-ray generation. On the contrary, these models find difficulties to describe the process when the various layers have very different atomic numbers. In a previous work, we studied the surface ionization of thin copper films of various thicknesses deposited on substrates with very different atomic numbers. In the present communication, the study is extended to the case of multilayered specimens.The studied specimens consisted of thin copper films deposited on a carbon layer which, in turn, was placed on a variety of single-element substrates, ranging from Be to Bi.

Thermodynamic and Kinetic Calculation of Non-Equilibrium Microstructure Design of TRIP Steel

2014 ◽  
Vol 783-786 ◽  
pp. 766-770
Author(s):  
Yan Lin He ◽  
Na Qiong Zhu ◽  
Wei Sen Zheng ◽  
Xiao Gang Lu ◽  
Lin Li
Keyword(s):  
Trip Steel ◽  
Equilibrium Phase ◽  
Microstructure Design ◽  
Kinetic Calculation ◽  
Software Comparison ◽  
Thermo Calc Software ◽  
Curve Determination ◽  
Equilibrium Microstructure ◽  
The Relationship ◽  
Non Equilibrium

The non-equilibrium microstructure of Fe-C-Mn-Si TRIP steel is designed bythermodynamic and kinetic calculation. The upper limit of bainitic transformation temperature iscalculated and compared to that characterized by CCT curve determination. s M temperature isdetermined based on thermodynamics of martensitic transformation and sublattice model. Thecalculation is conducted via TQ6-patch in Thermo-Calc software. Comparison between thecalculations and experiments reveals the relationship between non-equilibrium phase compositionand heat treatment parameters which can be utilized to achieve the elaborate design of alloy and heattreatment for super TRIP steel.

scholarly journals Modification of Non-Metallic Inclusions by Rare-Earth Elements in Microalloyed Steels

2012 ◽  
Vol 12 (2) ◽  
pp. 129-134 ◽  
Author(s):  
M. Opiela ◽  
A. Grajcar
Keyword(s):  
Rare Earth ◽  
Chemical Composition ◽  
Rare Earth Elements ◽  
Mechanical Treatment ◽  
Induction Furnace ◽  
Microalloyed Steels ◽  
Metallurgical Process ◽  
Metallic Inclusions ◽  
Mean Size ◽  
Thermo Mechanical Treatment

Modification of Non-Metallic Inclusions by Rare-Earth Elements in Microalloyed Steels The modification of the chemical composition of non-metallic inclusions by rare-earth elements in the new-developed microalloyed steels was discussed in the paper. The investigated steels are assigned to production of forged elements by thermo-mechanical treatment. The steels were melted in a vaccum induction furnace and modification of non-metallic inclusions was carried out by the michmetal in the amount of 2.0 g per 1 kg of steel. It was found that using material charge of high purity and a realization of metallurgical process in vacuous conditions result in a low concentration of sulfur (0.004%), phosphorus (from 0.006 to 0.008%) and oxygen (6 ppm). The high metallurgical purity is confirmed by a small fraction of non-metallic inclusions averaging 0.075%. A large majority of non-metallic inclusions are fine, globular oxide-sulfide or sulfide particles with a mean size 17 μm2. The chemical composition and morphology of non-metallic inclusions was modified by Ce, La and Nd, what results a small deformability of non-metallic inclusions during hot-working.

Sign in / Sign up

Export Citation Format

Share Document